MEWOI MEWOI8100E Manual de usuario

MEWOI8100E

Super Large Caliber AC/DC Clamp Meter

User Manual

www.mewoi.com

CONTENT

I. Safety Precautions And Procedures ............................................... 2

1. Preliminary Instructions............................................................... 3

2. During Use................................................................................... 3

3. After Use ...................................................................................... 4

II. Introduction........................................................................................ 4

III. Model................................................................................................. 4

IV. Electrical Symbols ........................................................................... 5

V. Technical Specification..................................................................... 5

VI. Instrument Structure........................................................................ 7

VIII. Method of Operation..................................................................... 8

1. Switch On/Off.......................................................................... 8

3. Peak Value Holding.................................................................. 9

4. Data Hold/Cancel/Storage/Consult/Delete............................. 10

5. Data Upload ............................................................................... 10

VII. Battery Replacement....................................................................11

VIII.Accessories...................................................................................11

-1-

Warning

Thanks for your purchase of MEWOI8100E Super Large Caliber AC/DC

Clamp Meter of our company. For better use of the product, please make

sure:

---To read this user manual in details.

---To abide by the safety regulations and precautions strictly.

♦Under any circumstance, it shall pay special attention on safety in use of this

tester.

♦Pay attention to words and symbols stick on the Tester.

♦Be careful while the measured line voltage is Exceed 60VDC or 30VAC.

♦Measured wire should at approximately the geometric center of the clamp,

The location deviation would increasing the measure error.

♦Please don’t place and store the instrument at the place with high

temperature, humidity, moisture condensation and straight sunlight for a long

time.

♦Replace battery in time when the battery voltage is low.

♦Take note of the polarity when replace the battery.

♦The operation, demolition, calibration and maintenance of the instrument

must be carried out by qualified personnel authorized to do so.

♦The meter should be stopped from being used immediately and sealed if

danger is brought up in case of continued use; only a competent body can be

authorized to deal with it.

♦“ ” in the manual is the safety warning sign, the contents of this manual

must be followed for safe operation.

♦“ ” and other safety signs, the contents of this manual must be followed

for safe operation.

-2-

I. Safety Precautions And Procedures

This instrument was designed in compliance with IEC1010-1& IEC1010-2-032

safety guideline relative to electronic equipment.

For your own safety and to avoid damaging the instrument you are

recommended to follow the procedures described in this manual and read

carefully all instructions preceded by this symbol

Before and during measurements keep to the following instructions:

●Do not take current measurements in wet places

●Do not take the measurements in the presence of explosive gas and

combustibles or in dusty places

●Avoid any contact with the circuit under test even though you are not

taking any measurement

●Avoid any contact with exposed metal parts, unused measuring terminals,

circuits etc. Do not take any measurement whenever anomalous conditions

occur such as deformations, breaks, leakages, blind display etc

The herewith symbols are used in this manual and on the meter

CAUTION: refer to the instruction manual. An improper use may

damage the instrument or its components as well as endanger the user.

High voltage danger: risk of electric shock

-3-

1. Preliminary Instructions

●This instrument has been designer for use in environments with pollution

degree 2

●It can be used for voltage and current measurements on electrical

installations with overvoltage CAT III 600V

●You are recommended to respect the usual safety regulations aimed at

protecting you against dangerous current and protecting the instrument

against improper use

●Only the original accessories supplied along with the instrument guarantee

compliance with the safety standards in force. They must be in a good

conditions and, if necessary, replaced with identical ones

●Do not test nor connect to any circuit exceeding the specified overload

protection

●Do not take measurements under environmental conditions exceeding the

limits indicated in this manual

●Make sure that batteries are correctly installed

2. During Use

You are recommended to read carefully the following instructions:

CAUTION

Failure to comply with warnings and instructions may damage the

instrument and/or its components as well as injure the operator

●Do not measure in the presence of external voltages. Although the

instrument is protected, an excessive voltage may cause malfunction

●Avoid submitting the instrument to voltage while measuring (i.e. a test lead

slipping off the measuring point accidentally touching an energized point)

CAUTION

-4-

If the “low battery”symbol is displayed during use

interrupt testing, switch off the instrument and replace batteries.

(Take note of the polarity when replace the battery.)

3. After Use

●Turn off the instrument pressing ON/OFF key after using it

●If you expect not to use the instrument for a long time remove batteries

II. Introduction

MEWOI8100E Super Large Caliber AC/DC Clamp Meter is well designed and

manufactured for measuring AC/DC current below 600V line Measure, it

adopt the latest CT technology and digital integrated technology. No exposed

metal conductor in the Clamp and no-contact measure model mean current

measure operation more safer and quicker. Super large Caliber is

particularly suitable for thick wire current measure. This meter is widely used

in electric power, communication, meteorology, railway, oil field, architecture,

measuring, teaching research unit, industrial mining enterprises, etc.

The instrument with current peak value holding, data holding, data storage

and other function. Equipped

With USB interface, communication line and supervision software, this meter

could achieve current online monitoring, show the real time current condition

via computer, with consult historical data, saving, print and other functions.

III. Model

Model

Range

Resolution

Note

MEWOI 8100E

DC:0.0A- 2000A

AC:0.0A~1000A

0.1A

Measure current

-5-

IV. Electrical Symbols

Extremely dangerous! The operator must strictly abide by the safety

rules; otherwise there is risk of electric shock, resulting in bodily

injury or fatalities.

Dangerous! The operator must strictly abide by safety rules;

otherwise there is risk of electric shock, resulting in bodily injury or

fatalities.

Warning! Safety rules must be strictly abided by, otherwise personal

injury or equipment damage may be caused.

Alternate Current（AC）

Direct Current（DC）

V. Technical Specification

Function

Measure AC/DC current, Current peak value holding, Online

current supervision

Power

6V DC(LR6×4 alkaline dry batteries)

Test Mode

Clamp CT, Non-contact Test mode

Clamp Size

108mm×148mm (can clamp electric cable of 108mm

diameter, or 160mm×4mm flat cable and steel earth wires)

Measurement

Range

DC:0.0A~2000A, AC:0.0A~1000A

Resolution

0.1A AC/DC

Measurement

Accuracy

(Reference

condition )

0.0mA~999A ±2%±5dgt

1000A~1499A ±3%±5dgt

1500A~2000A ±4%±5dgt

Reference

condition

23°C ±3°C , below 75%RH, measured wire at the center of

the clamp

Frequency

AC:45Hz~400Hz

-6-

response

Sample Rate

About 2 seconds per time

Measured

Wire Position

Measured wire at approximately the geometric center of the

clamp,the location deviation could increasing the

measurement error(maximum2%)

Display Mode

4 digitals LCD display

Dimension

L×W×H:350×180×55(mm)

LCD

Dimension

L×W:47×28.5(mm)

Polarity

Indication

Automatic recognize in AC test model ,display “-”

Gear Shift

Automatic shift

Line Voltage

Below 600V Line Measure

Software

Available, The stored data in instrument would upload to

computer via software.

USB interface

With USB interface ,upload data to computer ,software

supervision.

USB Line

1.5m

Data Storage

99 sets, “FULL”symbol indicate the memory is full

Peak Holding

Measure and Maintain the peak value, Press HOLD

and not let it go would show the peak value in test model .

Data Hold

“HOLD”symbol appears

Overflow

“OL”symbol appears

Automatic

Shutdown

Automatically shutdown about 5 minutes after power on t

o reduce battery consumption

Voltage

Detection

Low battery symbol “ " appears to remind the replac

ement of battery when the battery voltage drops below 4.

6V.

Weight of

Meter

1.5kg (with batteries)

Weight of

Package

2.6kg (with accessories)

Reference

Power

About 17mW

Working

Temperature

and Humidity

-10°C ~ 40°C ; 80%rh

Storage

-10°C ~ 60°C ; below 70%rh

-7-

Temperature

and Humidity

Insulation

strength

AC 3700kV/rms(between core and shell)

Safety

Specifications

IEC1010-1, IEC1010-2-032, 2 class of pollution, CAT III 600V

VI. Instrument Structure

1. Clamp (108mm×148mm)

2. Lock switch (after lock, the clamp can’t be open)

3. AC/DC Switch Key(Combination Key)

4. HOLD key (Combination Key) 5. READ display (Combination

Key)

6. LCD Display 7.USB Interface

8. Opening lever(Operate the clamp) 9. POWER key

10. ZERO key(DC Adjust zero key)

11. Battery cover 12. Battery cover screw

13. Up and down cover connecting screws (6 pieces)

-8-

VIII. Method of Operation

1. Switch On/Off

Press POWER key to switch on, LCD display, in test mode, press

POWER key to switch off. The meter LCD will twinkling 30 seconds after

booting 5 minutes later,then automatically power off. While the LCD is

Twinkling, Press POWER ,HOLD or READ ,the meter will keep working

for 5 minutes. If LCD display is darker, maybe the battery voltage is too low,

please replace batteries.

2. Current Measure

High voltage, very dangerous！Only qualified personnel

after training could conduct operation on it. The operator

should obey safety regulations; Otherwise there will be the

danger of electric shock resulting in personal injury or

casualty.

Dangerous! Can not be used to test voltage higher than

600V. Otherwise there will be the danger of electric shock

resulting in personal injury or casualty.

(1).Power

(2). Press / key to choose the kind of measurement. Adjust zero

before DC measure, the DC positive direction should toward the meter

front cover.

(3).In Current measure procedure, Measured wire should at

approximately the geometric center of the

clamp(location:”A”)(Attention:Measured wire in Location”B”will make

error increasing +2%, and in location”C”would make error increasing

-2%)

(4).Read the LCD display data, In case ”OL A”symbol was displayed, it

means that current of measured line is beyond the maximum limit of this

Meter; with this case, please choose Meter with much higher range limit.

Tabla de contenidos

Otros manuales de Instrumento de medición de MEWOI

MEWOI

MEWOI MEWOI9000G Manual de usuario

MEWOI

MEWOI MEWOI1200 Manual de usuario

MEWOI

MEWOI MEWOI8000B Manual de usuario

MEWOI

MEWOI 7800 Manual de usuario

MEWOI

MEWOI MEWOI1000 Manual de usuario

MEWOI

MEWOI MEWOI-JY218 Manual de usuario

MEWOI

MEWOI WBGT2019A Manual de usuario

MEWOI

MEWOI MEWOI1310B Manual de usuario

MEWOI

MEWOI 8000 Manual de usuario

MEWOI

MEWOI MEWOI1330B Manual de usuario

MEWOI

MEWOI MEWOI9000 Manual de usuario

MEWOI

MEWOI MEWOI7300E Manual de usuario

MEWOI

MEWOI MEWOI7900 Manual de usuario

MEWOI

MEWOI MEWOI-HY128 Series Manual de usuario

MEWOI

MEWOI MEWO1000T Manual de usuario

MEWOI

MEWOI MEWOI400 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario