Metrologic MS7120 Series Manual de usuario
METROLOGIC INSTRUMENTS, INC.
MS7120 Series Fixed Projection
Laser Scanner
Installation and User’s Guide
MLPN 2408
Printed in USA
December 1998
ii
Locations
USA Corporate Headquarters Europe
Metrologic Instruments, Inc. Metrologic Instruments GmbH
90 Coles Road Dornierstrasse 2
Blackwood, NJ 08012 82178 Puchheim b.
Customer Service: 1-800-ID-METRO Munich, Germany
Tel: 609-228-8100 Tel: 49-89-89018-0
Fax: 609-228-6673 Fax: 49-89-89019-200
www.metrologic.com
ASIA
South America Metrologic Asia (PTE) Ltd.
Metrologic Instruments 31, Khaki Bukit Road 3
Rua Flórida, 1.821-5°Andar-Brooklin #05-08 Techlink
CEP 04571-090, São Paulo-SP, Brasil Singapore 417818
Outside Brazil: Tel: 65-842-7155
Tel: 55-11-5505-6568 Fax: 65-842-7166
In Brazil:
Tel: 55-11-5505-2396
Fax: 55-11-5507-2301
Copyright
© 1998 by Metrologic Instruments, Inc. All rights reserved. No part of this work may
®
be reproduced, transmitted, or stored in any form or by any means without prior written
consent, except by reviewer, who may quote brief passages in a review, or provided for
in the Copyright Act of 1976.
Products and brand names mentioned in this document are trademarks of their
respective companies.
iii
Table of Contents
Introduction ................................................... 1
Scanner and Accessories ......................................... 2
Quick Start .................................................... 3
Operational Test ............................................... 4
Scanner Installation: Powered by External Power Supply ............... 5
Scanner Installation: Powered by the Host Device ..................... 6
Scanner Installation: to the PC for the Scanner with built-in
PC Keyboard Wedge Interface .................................... 7
Scanner Parts .................................................. 8
Audible Indicators ............................................. 9
Failure Modes ......................................... 10
Visual Indicators .............................................. 11
Labels ....................................................... 12
Depth of Field Specifications .................................... 13
Optimal Low Density Depth of Field ...................... 13
Optimal High Density Depth of Field ...................... 13
Close Depth of Field .................................... 14
Normal Depth of Field .................................. 14
Far Depth of Field ...................................... 15
Minimum Bar Code Element From Scanner Face .................... 16
Optimal Low Density Depth of Field ....................... 16
Optimal High Density Depth of Field ...................... 17
Close Depth of Field .................................... 18
Normal Depth of Field .................................. 19
Far Depth of Field ...................................... 20
Maintenance .................................................. 21
Troubleshooting Guide ...................................... 22-26
RS-232 Demonstration Program .................................. 27
Application and Protocols ....................................... 28
iv
Table of Contents (continued)
Appendix A
Design Specifications 29, 30
Appendix B
Default Settings 31-35
Appendix C
Pin Assignments 36-38
Appendix D
Warranty and Disclaimer 39, 40
Appendix E
Notices 41, 42
Index 43, 44
1
Introduction
Orbit™ is an aggressive, omnidirectional laser bar code scanner. Light-weight
and rugged, Orbit is small in size, but BIG in performance. Designed for
applications where counter space is limited, Orbit is the ideal presentation
scanner for retail, convenience, liquor and specialty stores. In addition, Orbit’s
unique, contoured shape allows it to be picked-up and used as a hand-held
scanner when scanning large or bulky items.
Engineered with a large, easy-to-find optimal scan area, Orbit increases the
first pass read rate for maximum productivity. The scanning head can be tilted
vertically a full 30 for added flexibility when scanning various sized objects.
o
These features increase the scanning throughput without increasing the
scanner size.
SCANNER INTERFACE
7120-41 Full RS-232C and Light Pen Emulation
7120-47 Keyboard Wedge, Stand-Alone Keyboard and
RS-232 Transmit/Receive
7120-9 OCIA and RS-232 Transmit/Receive
7120-11 IBM 46XX/RS-232C
7120-67 Full RS-232C and Light Pen Emulation
Orbit offers a great deal of features to the consumer:
‚Fully automatic scanning operation
‚PowerLink compatible
‚Data editing
‚7 beeper tones
‚Programmable depth of field
‚Easy programming
2
Scanner and Accessories
The following is a list of the parts included in the MS7100 kit.
!MS7120 Laser Scanner - Refer to page 28 for available
communication protocols
!Power Transformer AC in 120V, 220V- 240V Continental
European or 220V- 240V UK. DC in regulates 5.2V@650mA
(MLPN45593/45591/45592)
RS-232, Light Pen, OCIA and 46xx scanners:
!PowerLink cable with built in power jack:
Standard - MLPN 54xxx* - 2.1m (7') straight cord, short strain relief
or
Optional - MLPN 53xxx* - 2.7m (9') coiled cord, long strain relief
*xxx specifies connection to the host
Keyboard Wedge Scanners:
!Keyboard Wedge PowerLink Cable with a 5-pin
DIN female connector and a 6-pin mini DIN male
connector (MLPN 19763)
!Adapter Cable with a 5-pin DIN male
connector and a 6-pin mini DIN female
connector (MLPN 19716)
Available on the Metrologic Website (www.metrologic.com):
!MetroSelect Programming Guide (MLPN 2407)
!MS7120 User’s and Installation Guide (MLPN 2408)
Options
!Counter/Wall Mount Kit (MLPN 45619)
Other items may be ordered for the specific protocol being used. To order additional
items, contact the dealer, distributor or call Metrologic’s Customer Service Depart-
ment at 1-800-ID-METRO or 1-800-436-3876.
3
Quick Start
1.) Plug in the scanner. When the MS7120 is ready to scan,
the green LED will turn on, then the red LED will flash
and the scanner will beep once. (the red LED will
remain on for the duration of the beep).
2.) The scanner is shipped from the factory programmed with
default settings. To configure the MS7120 scanner to
meet the host system’s specific needs, refer to the Metro-
Select Programming Guide (MLPN 2407) for instructions
on how to enter the program mode and to select the
appropriate bar codes.
4
Operational Test
Metrologic recommends using the external power supply provided with the
scanner when operating the MS7120. When using power supplied by the host,
the host system should supply a minimum of 250 mA of current @ 5VDC.
Keyboard Wedge Scanners:
1. Connect the 10-pin modular plug of the PowerLink cable into the
scanner jack. Connect the other end of the PowerLink Y-type cable
to the PC. Connect the 5-pin female DIN side of the Y-type cable
into the keyboard connector on the PC and connect the 6-pin male
mini-DIN side into the PC.
2. Check the AC input requirements of the power supply to make sure the
voltage matches the AC outlet. Connect AC power to the transformer.
3. Listen for a single beep that indicates the scanner is ready for use.
(steady green LED and the red LED will flash once)
RS-232, Light Pen, OCIA and 46xx scanners:
1. Connect the 10-pin modular plug of the PowerLink cable into the scanner
jack. Connect the other end of the PowerLink cable (the 9-pin D-type
connector) to the PC.
2. Check the AC input requirements of the power supply to make sure the
voltage matches the AC outlet. Connect AC power to the transformer.
3. Listen for a single beep that indicates the scanner is ready for use.
(steady green LED and the red LED will flash once)
5
Scanner Installation: Powered by External Power Supply
To maintain compliance with applicable standards, all circuits connected to the
scanner must meet the requirements for SELV (Safety Extra Low Voltage)
according to EN 60950.
1. Turn off the host system.
2. Make the necessary PowerLink cable connections to the scanner and
the host.
3. Connect the external transformer into the power jack on the Power Link
cable.
4. Check the AC input requirements of the power supply to make sure the
voltage matches the AC outlet. (the socket-outlet shall be installed near
the equipment and shall be easily accessible.) Connect AC power to the
transformer.
5. Turn on the host system.
NOTE:
a. When the scanner first receives power, the green LED will
turn on. Then the scanner will beep once and the red LED
will flash simultaneously.
b. Plugging the scanner into the serial port of the PC does not
guarantee that scanned information will appear at the PC. A
software driver and correct configuration setting are also
required for proper communication to occur.
6
Scanner Installation: Powered by Host Device
The MS7120 scanner interfaces terminate to a 10-pin modular jack. Connect
the 10-pin modular plug of the PowerLink cable into the jack then connect the
other end of the PowerLink cable to the host. Refer to Appendix C page 36 for
pin assignments.
1. Turn off the host system.
2. Make the necessary PowerLink cable connections to the scanner and the
host.
3. Turn on the host system.
NOTE:
a.When the scanner first receives power, the green LED will turn
on. Then the scanner will beep once and the red LED will
flash simultaneously.
b.Plugging the scanner into the serial port of the PC does not
guarantee that scanned information will appear at the PC. A
software driver and correct configuration setting are also
required for proper communication to occur.
Tabla de contenidos
Otros manuales de Lector de código de barras de Metrologic
Metrologic
Metrologic IS421X ScanGlove Manual de usuario
Metrologic
Metrologic MLPN 2159 Manual de usuario
Metrologic
Metrologic ScanQuest IS4110 Manual de usuario
Metrologic
Metrologic IS4910 Series Manual de operación y mantenimiento
Metrologic
Metrologic MS9500 Voyager Series Manual de usuario
Metrologic
Metrologic Tire and Rubber Guía del usuario
Metrologic
Metrologic MS7600 Manual de usuario
Metrologic
Metrologic MS863 Manual de usuario
Metrologic
Metrologic MS9590 VOYAGERGS series Manual de usuario
Metrologic
Metrologic IS3480 QuantumE Manual de usuario
Metrologic
Metrologic IS1000 Series Manual de usuario
Metrologic
Metrologic FocusE IS1650 Manual de usuario
Metrologic
Metrologic MS5100 Eclipse Series Manual de usuario
Metrologic
Metrologic MS 1690 Focus Series Manual de usuario
Metrologic
Metrologic Stratos MS2x20 Series Instrucciones de instalación y funcionamiento
Metrologic
Metrologic MS9530 Series Manual de usuario
Metrologic
Metrologic MS 1690 Focus Series Manual de usuario
Metrologic
Metrologic MS1633 FocusBT Manual de usuario
Metrologic
Metrologic MH941 Manual de usuario
Metrologic
Metrologic MK1690-61A38 Manual de usuario
