METREL A 1740 Manual de usuario

METREL test and measurement accessories:

Calibration Box 5kV

A 1740

Instruction manual

Version 1.1.1, Code no. 20 753 135

Distributor:

Manufacturer:

METREL d.d.

Ljubljanska cesta 77

1354 Horjul

Slovenia

web site: http://www.metrel.si

e-mail: metrel@metrel.si

No part of this publication may be reproduced or utilized in any form or by any means

without permission in writing from METREL.

A 1740 Calibration Box 5kV Table of contents

Table of contents

1Preface ...................................................................................................4

2Safety and operational considerations...............................................4

2.1 Warnings and notes..............................................................................................4

2.2 Markings on the A 1740........................................................................................4

2.3 Standards applied.................................................................................................5

3A 1740 Description................................................................................5

4A 1740 Application................................................................................5

5Maintenance...........................................................................................6

5.1 Cleaning................................................................................................................6

5.2 Service..................................................................................................................6

6Technical specifications.......................................................................6

A 1740 Calibration Box 5kV Preface / Safety and operational considerations

1 Preface

It is essential that all measurement instruments are regularly calibrated. For occasional

daily use we recommend an annual calibration to be carried out. When the instrument is

used continuously every day, shorter periodical calibration of the instrument is

recommended.

A 1740 Calibration Box 5kV is optional accessory intended for time-to-time verification

of insulation resistance measurement of the Metrel instruments. This unit contains four

high ohm resistors enclosed in plastic package.

2 Safety and operational considerations

2.1 Warnings and notes

In order to reach high level of operator’s safety as well as to keep the accessory and

equipment undamaged, it is necessary to consider the following general warnings:

Warning on the A 1740 means »Read the Instruction manual with

special care to safety operation«. The symbol requires an action!

If the A 1740 is used in a manner not specified in this Instruction manual or

the manual of target test equipment, the protection provided by the A 1740

and equipment may be impaired!

Read this Instruction manual carefully, otherwise use of the A 1740 may be

dangerous for the operator, for test equipment or for the tested object!

Do not use the A 1740 if any damage is noticed!

Consider all generally known precautions in order to avoid risk of electric

shock while dealing with hazardous voltages!

Service intervention is allowed to be carried out only by a competent

authorized person!

The A 1740 is intended to be applied with Metrel insulation testers!

2.2 Markings on the A 1740

Symbol

Description

Read the Instruction manual with special care to safety operation«.

The symbol requires an action!

The symbol on the Calibration Box 5kV means “Hazardous voltage may

be present at the test terminals!”.

Mark on your equipment certifies that it meets requirements of all

subjected EU regulations.

This equipment should be recycled as electronic waste.

A 1740 Calibration Box 5kV A 1740 Description / A 1740 Application

2.3 Standards applied

A 1740 Calibration Box 5kV is manufactured and tested according to the following

regulations, listed below.

Safety

EN 61010 - 1

Safety requirements for electrical equipment for measurement,

control, and laboratory use –Part 1: General requirements

3 A 1740 Description

Outlook of calibration unit

Figure 3.1: Calibration Box 5kV (A 1740)

Legend:

1......................................10 Mconnection stub, (intended for connection of +Rx)

2......................................100 Mconnection stub, (intended for connection of +Rx)

3......................................1 Gconnection stub, (intended for connection of +Rx)

4......................................10 Gconnection stub, (intended for connection of +Rx)

5......................................COMMON connection stub, (intended for connection of –Rx)

4 A 1740 Application

Procedure:

Connect –RX to COMMON connection stub and +Rx to 10 Mconnection

stub.

Set test voltage, press START / STOP key on the instrument and wait until

result becomes stable, then verify indication.

Press START / STOP key again to stop the measurement.

Repeat the same procedure with the rest test values.

The instrument does not require any adjustment if indications are inside the stated

limits.

A 1740 Calibration Box 5kV Maintenance / Technical specifications

Warning:

Do not touch Calibration Box 5 kV (A 1740) during measurement! Risk of

electric shock!

Notes:

Pay attention on humidity condition and dirt of the instrument, test leads and

calibration unit due to their high influence on results especially when very high

resistances are measured. It should take an hour or more to adopt the instrument

and calibration unit on new environmental condition.

Keep calibration unit in bubble package when it is not used. Dirt on surface of

calibration unit can significantly reduce the value of reference resistors.

5 Maintenance

Unauthorized person is not allowed to open the A 1740. There are no user replaceable

components inside the calibration unit.

5.1 Cleaning

No special maintenance is required for the housing.

Use soft patch moisten by water or alcohol, and leave the calibration unit to dry totally

after the cleaning.

Warnings:

Do not use liquids based on petrol or hydrocarbons!

Do not spill cleaning liquid over the calibration unit!

5.2 Service

For repairs under warranty, or at any other time, please contact your distributor.

6 Technical specifications

Reference resistors:

Nominal resistance value

Temperature

coefficient

Voltage coefficient

Ratings

10 M

± 200 ppm / °C

< 10 ppm / V

2500 V

100 M

5000 V

1 G

5000 V

10 G

5000 V

General:

Calibration accuracy......................... 1 %

Nominal value accuracy.................... 2 %

Pollution degree................................ 2

Dimensions (W x H x L).................... 113 mm x 39 mm x 62 mm

Case................................................. plastic

Altitude.............................................. 2000 m

Reference temperature range........... 10 C … 30 C

Reference humidity range................. 40 % RH … 60 % RH

Mass................................................. 120 g

Operation.......................................... Indoor use

Tabla de contenidos

Otros manuales de Instrumento de medición de METREL

METREL

METREL DELTAPAT 3309 Manual de servicio

METREL

METREL MI 3102 Manual

METREL

METREL MD 126 Manual de usuario

METREL

METREL EurotestDL Manual de usuario

METREL

METREL TeraOhmXA 10 kV Manual de usuario

METREL

METREL MicroOhm 2A MI 3242 Manual de usuario

METREL

METREL MI 3103 Manual de usuario

METREL

METREL MD 9235 Manual de usuario

METREL

METREL MD 9250 Manual de usuario

METREL

METREL MI 3295 Manual de usuario

METREL

METREL A 1588 Manual de usuario

METREL

METREL EurotestPV Lite MI 3109 Manual de usuario

METREL

METREL eMobility A 1632 Manual de usuario

METREL

METREL MD 9273 Manual de usuario

METREL

METREL MI 3321 MultiservicerXA Manual de usuario

METREL

METREL EurotestAT MI 3101 Manual de usuario

METREL

METREL A 1501 Manual de usuario

METREL

METREL MD 9272 Manual de usuario

METREL

METREL A 1445 Manual de usuario

METREL

METREL EurotestCOMBO MI 3125 Manual de usuario

METREL

METREL Instaltest 61557 MI 2087 Manual de usuario

METREL

METREL EurotestAT MI 3101 Manual

METREL

METREL A1199 Manual de usuario

METREL

METREL MD 9273 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario