Metra Electronics AT-807HD Manual de usuario

REV. 10/15/2015 INST-99-7898

Installation instructions for part 99-7898

CAUTION!

Metra recommends disconnecting the negative bat

tery terminal before beginning any installation, unless the vehicle

manufacturer recommends against so. Please check with your local

Dealership for more information. All accessories, switches, climate

controls panels, and especially air bag indicator lights must be con

nected before reconnecting the battery or cycling the ignition. Also,

do not remove the factory radio with the key in the on position, or the

vehicle running. It would be best to remove the key from the ignition

and then wait a few seconds before removing the factory radio.

• DIN radio provision with pocket

• ISO DIN radio provision with pocket

• Pocket holds (2) jewel cases

• A) Radio housing • B) Faceplate • C) ISO trimming • D) ISO spacers • E) ISO brackets

• F) Mounting brackets • G) Rear support bracket (R1) • H) Rear support bracket (R2)

• I) (2) #8 x 3/4” Phillips screws • J) (6) #8 x 3/8” Phillips screws

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness:

• 70-1720

• 70-1721

Antenna Adapter:

• Not required

• Phillips screwdriver • Cutting tool

TOOLS REQUIRED

Acura/Honda/Isuzu 1990-2006

99-7898

AT-807HD, IBR-807HD, CF-807HD, AW-807HD

See application list inside

B EC DA F G

H I J

Applications

99-7898

Table of Contents

Acura

CL ................................... 1997-1999

Integra............................. 1990-2001

Legend ............................ 1990-1995

RSX ................................. 2002-2006

TL.................................... 1996-1998

Vigor................................ 1992-1994

Honda

Accord............................. 1990-2002

Civic ................................ 1996-2000

Civic SE ........................... 2005 (only)

CRV ................................. 1997-2006

Odyssey........................... 1995-1998

Odyssey (without NAV)..... 1999-2004

Prelude............................ 1989-2001

Isuzu

Oasis ............................... 1996-1999

Dash Disassembly

- Acura CL 1997-1999 .......................................... 3

- Acura Integra 1990-1993.................................... 3

- Acura Integra 1994-2001.................................3-4

- Acura Legend 1990-1995 ................................... 4

- Acura RSX 2002-2006 ........................................ 5

- Acura TL 1996-1998........................................... 5

- Acura Vigor 1992-1994....................................... 6

- Honda Accord 1990-1993 ................................... 6

- Honda Accord 1994-1997 ................................... 7

- Honda Accord 1998-2002 ................................... 7

- Honda Civic 1996-1998 ...................................... 8

- Honda Civic 1999-2000 ...................................8-9

- Honda Civic SE 2005 (only) .................................. 9

- Honda CRV 1997-2001 ..................................... 10

- Honda CRV 2002-2006 ..................................... 10

- Honda Odyssey 1995-1998............................... 11

- Honda Odyssey 1999-2004 (without NAV)......... 11

- Honda Prelude 1989-1991................................ 12

- Honda Prelude 1992-1996................................ 12

- Honda Prelude 1997-2001................................ 13

- Isuzu Oasis 1996-1999..................................... 11

Kit Assembly

- DIN radio provision

(Honda Civic 1996-1998 only) ......................... 13

- DIN radio provision with pocket......................... 14

- ISO DIN radio provision with pocket................... 15

99-7898

1. Remove (3) screws

from each side of the

center console and

remove the console.

2. Remove (2) screws

securing the factory

radio to the sub-dash

support bracket. Slide

the radio/pocket

assembly out and

disconnect the wiring.

(Figure A)

3. Cut and remove all

of the mounting clips

on the radio housing

EXCEPT clips “C” and

“H” (the clips can

be identified by the

stamped letter on the

back of the housing,

near each clip).

(Figure B)

Continue to kit assembly

Acura Integra 1990-1993

Dash Disassembly

1. Unclip the radio trim

bezel and disconnect

the clock and climate

control wiring.

(Figure A)

2. Remove (2) 8mm

hex head screws

securing the factory

radio and disconnect the

wiring.

3. Cut and remove all

of the mounting clips

on the radio housing

EXCEPT clips “A” and

“H” (the clips can

be identified by the

stamped letter on the

back of the housing,

near each clip).

(Figure B)

4. Mount the rear support

bracket (R1) to the back

of the radio housing with

(2) #8 x 3/8” Phillips pan

head screws supplied. (Figure B)

Continue to kit assembly

Acura CL 1997-1999

(Figure B)

(Figure A)

“H”

“A”

(Figure B)

(Figure A)

“H”

“C”

1. Remove the cover cap located under the

emergency brake and remove (2) screws exposed.

2. Remove (2) screws from the rear corners of the

lower dash trim bezel and remove.

3. Remove the ashtray and (2) screws exposed.

4. Unsnap the ashtray housing and disconnect the

cigarette lighter harness.

5. Remove the gear shifter knob and unsnap the

shifter trim.

Continue on next page

Acura Integra 1994-2001

(Figure A)

99-7898

Dash Disassembly

6. Remove (2) screws below the radio opening and

remove the upper dash trim bezel. (Figure A)

7. Remove (2) 8mm screws securing the factory radio

and disconnect the wiring.

8. Cut and remove all of the mounting clips on the

radio housing EXCEPT clips “C” and “H” (the clips

can be identified by the stamped letter on the back

of the housing, near each clip). (Figure B)

Continue to kit assembly

Acura Integra 1994-2001

(Figure B)

“H”

“C”

1. Remove (2) screws below the ashtray. (Figure A)

2. Unclip the dash trim bezel.

3. Disconnect the cigarette lighter wiring and remove the bezel.

4. Remove (2) bolts securing the rear of the factory radio and

disconnect the wiring.

5. Cut and remove all of the mounting clips on the radio housing

EXCEPT clips “E” and “J” (the clips can be identified by the

stamped letter near each clip). (Figure B)

Continue to kit assembly

Acura Legend 1990-1995

(Figure B)

(Figure A)

“J”

“E”

(Figure B)

“J”

1. Using a small screwdriver, unclip the

perimeter of the radio trim bezel.

(Figure A)

2. Disconnect the climate control

and rear defroster wiring and

remove the bezel.

3. Remove (4) Phillips screws securing

the factory radio/trim bezel

assembly. (Figure A)

4. Loosen (2) Phillips screws securing

the back of the radio to the metal

housing and slide the radio out (it is

not necessary to remove the screws

securing the metal).

5. Disconnect the wiring.

6. Cut and remove all of the mounting

clips on the radio housing EXCEPT

clips “B” and “K” (the clips can be

identified by the stamped letter near

each clip). (Figure B)

Continue to kit assembly

(Figure A) (Figure B)

“K”

“B”

(Figure A)

1. Unclip the lower dash panel (containing the power outlet) and remove the panel.

Reach into the opening and remove (2) Phillips screws from the base of the factory radio.

3. Slide the factory radio (with bracket assembly) from the dash and disconnect

the wiring. (Figure A)

4. Remove (4) Phillips screws securing the factory radio to the bracket assembly

and remove the radio (if a factory pocket is present, remove (4) Phillips screws

securing the pocket to the bracket assembly and remove). (Figure A)

5. Cut and remove the all mounting clips on the radio housing EXCEPT clips “J”

(the clips can be identified by the stamped letter near each clip). (Figure B)

6. Mount the rear support bracket (R2) to the back of the radio housing with (2) #8

x 3/8” Phillips pan head screws supplied.

Continue to kit assembly

Acura RSX 2002-2006 (except “S” model)

Dash Disassembly

Acura TL 1996-1998

99-7898

1. Remove the access cap from the

climate control cluster and (1) screw

exposed. (Figure A)

2. Unclip the cluster and remove (2)

screws exposed. (Figure A)

3. Remove the ashtray and (2) Phillips

screws exposed.

4. Remove the cover caps from each

front corner of the center console

and the screws exposed.

5. Open the storage compartment,

lift up the carpet and remove (2)

screws exposed.

6. Lift up on the center console and

remove. Unclip the radio trim bezel

and disconnect the wiring.

Remove (2) bolts from the back of the

factory radio and disconnect the wiring

8. Cut and remove all of the mounting

clips on the radio housing EXCEPT

clips “A” and “H” (the clips can be

identified by the stamped letter on

the back of the housing, near each

clip). (Figure B)

Continue to kit assembly

Acura Vigor 1992-1994

(Figure B)(Figure A)

“H”

“A”

“H”

“C”

1. Remove (4) screws from the lower

portion of the center console.

(Figure A)

2. Remove the gear shifter knob and

lift the console out. Remove the

ashtray and ashtray bracket.

3. Remove (2) screws from the

bottom of the radio support,

slide the radio out and disconnect

the wiring.

4. Cut and remove all of the mounting

clips on the radio housing EXCEPT

clips “C” and “H” (the clips can be

identified by the stamped letter on

the back of the housing, near each

clip). (Figure B)

Continue to kit assembly

Honda Accord 1990-1993

(Figure B)

(Figure A)

99-7898

Dash Disassembly

1. Remove the ashtray and (1) 3/4” #8

Phillips screw exposed. Open the

storage compartment and remove

(2) #8 Phillips screws exposed.

2. Remove the cup holder tray and (3)

#8 Phillips screws inside.

3. Lift the center console out and

remove (2) Phillips screws exposed

at the base of the dash trim bezel.

4. Unclip the bezel and remove.

5. Remove (2) hex head screws

securing the factory radio and

disconnect the wiring. (Figure A)

6. Cut and remove all of the mounting

clips on the radio housing EXCEPT

clips “A” and “H” (the clips can be

identified by the stamped letter on

the back of the housing, near each

clip). (Figure B)

7. Mount the rear support bracket (R1)

to the back of the radio housing

with (2) #8 x 3/8” Phillips pan head

screws supplied.

Continue to kit assembly

Honda Accord 1994-1997 Honda Accord 1998-2002

(Figure B)(Figure A)

1. Unsnap the clock panel, disconnect

the wiring and remove. (Figure A)

2. Remove (1) Phillips screw exposed

in the clock cavity.

3. Remove (2) Phillips screws below

the factory radio.

4. Unclip the radio trim bezel and

disconnect the wiring. (Figure A)

5. Remove (4) Phillips screws securing

the factory radio assembly and

disconnect the wiring.

6. Remove (2) screws securing the

factory pocket to the assembly.

7. Cut and remove the mounting clips

from the radio housing.

8. From the mounting brackets cut and

remove tabs “B” (the clips can be

identified by the stamped letter on

the back of the housing, near each

clip). (Figure B)

9. Secure the brackets to the

housing with (4) #8 x 3/8” Phillips

pan head screws.

Continue to kit assembly

(Figure B)(Figure A)

“B”

“H”

“A”

99-7898

Dash Disassembly

Honda Civic 1999-2000

1. Remove (2) Phillips screws

from the bottom edge of

the glove box door and

remove the door.

2. Remove (3) Phillips screws

from the lower steering

column panel.

3. Pull straight down

on the lower steering

column panel and remove

the panel.

4. Remove (2) Phillips screws

under the climate controls.

5. Remove (4) Phillips screws

from the lower dash

location. (Figure A)

6. Remove (4) Phillips screws

securing the bottom of

the dash trim bezel/radio

assembly and pull the

assembly out as far as

possible.

(Figure A) (Figure B)

“H”

“B”

1. Remove (2) Phillips screws from the

bottom edge of the glove box door and

remove the door.

2. Remove (3) Phillips screws from the lower

steering column panel.

3. Pull straight down on the lower steering

column panel and remove the panel.

4. Remove (2) Phillips screws under the

climate control panel. (Figure A)

5. Remove (4) Phillips screws from the lower

dash location.

6. Remove (2) 8mm hex head screws securing

the bottom-rear of the factory radio and

disconnect the wiring.

7. Locate the faceplate. (Figure B)

Continue to kit assembly

Honda Civic 1996-1998

(Figure B)

(Figure A)

99-7898

Dash Disassembly

Honda Civic SE 2005 (only)

1. Unsnap and remove the trim ring from

around floor shifter.

2. Unsnap and remove larger trim around

floor console shifter.

3. Remove (2) Phillips screws from in

between cup holder and shifter.

(Figure A)

4. Unsnap sides of console (2 snaps per

side) and remove with power

outlet assembly.

5. Remove (2) Phillips screws from under

radio assembly, facing up. (Figure A)

6. Remove (3) screws securing the climate

control pod to the back of the dash trim

bezel and remove the pod. (Figure B)

7. Remove (4) Phillips screws from each

side securing the factory head radio to the

bracket assembly and remove the radio.

8. Cut and remove all mounting clips on

the radio housing, EXCEPT clips “B”

and “H” (the clips can be identified by

the stamped letter on the back of the

housing, near each clip). (Figure C)

Continue to kit assembly

(Figure A) (Figure B) (Figure C)

“H”

“B”

Honda Civic

1999-2000

7. Cut the zip ties securing

the radio and climate

control wires, slide the

dash trim bezel/radio

assembly from the dash

cavity and disconnect the

wiring.

8. Cut and remove all of the

mounting clips on the

radio housing EXCEPT

clips “B” and “H” (the

clips can be identified by

the stamped letter on the

back of the housing, near

each clip).

(Figure B)

Continue to kit assembly

99-7898

Dash Disassembly

1. Remove (2) Phillips screws

from the bottom edge of the radio

trim bezel. (Figure A)

2. Unclip the trim bezel and remove.

3. Remove (4) Phillips screws

securing the factory radio and

disconnect the wiring.

4. Cut and remove all of the mounting

clips on the radio housing EXCEPT

clips “A” and “H” (the clips can be

identified by the stamped letter on

the back of the housing, near each

clip). (Figure B)

Continue to kit assembly

Honda CR-V 2002-2006

(Figure B)

(Figure A)

“H”

1. Open the glove box, squeeze

the retaining clips and remove

the stoppers.

2. Lower the glove box and remove (2)

Phillips screws from the left edge.

3. Remove (2) Phillips screws

from the lower steering column

panel and remove.

4. Unclip the lower console cover (below

the ashtray and pocket) and remove.

5. Remove (2) Phillips screws from the

base of the center console, open

the console pocket and remove the

(4) outer screws exposed.

6. Unclip the center console and remove.

7. Remove (2) Phillips screws securing

the radio trim bezel, disconnect the

wiring, and remove the trim bezel/

radio assembly. (Figure A)

8. Remove (4) Phillips screws securing

the radio to the bezel and remove.

9. Cut and remove all of the mounting

clips on the radio housing EXCEPT

clips “B” and “H” (the clips can be

identified by the stamped letter on

the back of the housing, near each

clip). (Figure B)

Continue to kit assembly

Honda CR-V 1997-2001

(Figure A) (Figure B)

“H”

“B”

99-7898

“A”

Dash Disassembly

Otros manuales para AT-807HD

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Receptor de coche de Metra Electronics

Metra Electronics

Metra Electronics 99-5722 Manual de usuario

Metra Electronics

Metra Electronics 95-7510 Manual de usuario

Metra Electronics

Metra Electronics 99-5700 Manual de usuario

Metra Electronics

Metra Electronics 99-8907HG Manual de usuario

Metra Electronics

Metra Electronics 99-2003 Manual de usuario

Metra Electronics

Metra Electronics 99-5815 Manual de usuario

Metra Electronics

Metra Electronics 99-3010S Manual de usuario

Metra Electronics

Metra Electronics 99-5815 Manual de usuario

Metra Electronics

Metra Electronics Ford F-150 2009-up Manual de usuario

Metra Electronics

Metra Electronics 99-7313 Manual de usuario

Metra Electronics

Metra Electronics 95-7882B Manual de usuario

Metra Electronics

Metra Electronics 99-5839CH Manual de usuario

Metra Electronics

Metra Electronics 99-6504 Manual de usuario

Metra Electronics

Metra Electronics 99-7427 Manual de usuario

Metra Electronics

Metra Electronics 99-6544B Manual de usuario

Metra Electronics

Metra Electronics 99-5025 Manual de usuario

Metra Electronics

Metra Electronics 95-8210 Manual de usuario

Metra Electronics

Metra Electronics 95-2005B Manual de usuario

Metra Electronics

Metra Electronics 99-2020 Manual de usuario

Metra Electronics

Metra Electronics 99-7809B Manual de usuario

Metra Electronics

Metra Electronics 99-5810 Manual de lista de piezas

Metra Electronics

Metra Electronics BUICK Lacrosse 2005-2009 Manual de usuario

Metra Electronics

Metra Electronics 99-6527B Manual de usuario

Metra Electronics

Metra Electronics 99-7509 Manual de usuario

Manuales populares de Receptor de coche de otras marcas

Motorola

Motorola VWA63 Manual de usuario

Nextar

Nextar D3201 Manual de usuario

Alpine

Alpine CDE-163BT Manual de usuario

Pioneer

Pioneer DEH-P645R Manual de usuario

Axxera

Axxera XDMA7600 Instrucciones de funcionamiento

XM OnyX Manual de usuario

Sound Storm

Sound Storm STM93R Manual de usuario

Soundstream

Soundstream VIR-5000 Manual de usuario

Avson

Avson MKT Platform Manual de usuario

Sony

Sony MEX-1HD - Audio Library System Manual de usuario

Pioneer

Pioneer DVH-P500UB Manual de usuario

JVC

JVC KD-AHD69 Manual de usuario

Blaupunkt

Blaupunkt SANTIAGO CR 87 Manual de usuario

Sony

Sony CDX-4160 - Cd Receiver Manual de usuario

XFIRE AUDIO

XFIRE AUDIO BMW42S Manual de usuario

VDO

VDO CD 2253 Manual de usuario

Volvo

Volvo 13 84 580 Manual de usuario

ZENEC

ZENEC ZE-160DVD Manual de usuario