Metra Electronics 99-8163 Manual de usuario
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 11/30/18 INST99-8163
INSTALLATION INSTRUCTIONS
99-8163
Attention! Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
KIT FEATURES
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• Painted two-tone gray and black
• Touchscreen display for the climate control
• Passenger seatbelt and airbag indicator
Note: The kit will not retain the factory amplifier
KIT COMPONENTS
• A) Radio trim panel with touchscreen display • B) Radio brackets • C) Pocket • D) (8) #8 x 3/8” Phillips screws
• E) Axxess interface and harnesses (not shown)
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 10mm socket wrench
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Assembly
–ISO DIN radio provision with pocket ..................3
–ISO DDIN radio provision .....................................4
Axxess Interface Installation .................................5
WIRING & ANTENNA CONNECTIONS
Wiring Harness: Axxess touch screen interface
and wiring harnesses included
Antenna Adapter:
Included with kit
Amp Bypass Harness: Included with kit
A B C D
Lexus IS 250/350* - 2006-2013
Lexus IS 250C/350C* - 2006-2015
* U.S. models only
1.800.221.0932
|
MetraOnline.com
2
1. Unclip and remove the (2) small trim
panels from the top of the center
console next to the cigarette lighter
pocket. (Figure A)
2. Rotate the a/c vents down so they are
facing the floor, release the (4) tabs
inside the top edge of the panel, then
unclip and remove the a/c vents from
the dash. (Figure B, C)
3. Remove (4) 10mm bolts securing the
factory radio/climate control assembly,
then unplug all harnesses and remove
the assembly. (Figure D)
4. Behind the radio/climate control panel
is a module. This module will need
to be relocated to allow room for the
aftermarket radio.
Continue to Kit Preparation
(Figure B) (Figure D)
(Figure A) (Figure C)
DASH DISASSEMBLY
REV. 11/30/2018 INST99-8163 3
KIT ASSEMBLY
ISO DIN radio provision with pocket
1. Attach the
radio brackets
to the
radio
trim panel with touchscreen
using the
(4) #8 x 3/8”
Phillips screws
supplied.
(Figure A)
2. Attach the
pocket
to the
radio brackets
using the (4) #8 x 3/8”
Phillips screws
supplied. (Figure B)
3. Remove the metal DIN sleeve and trim
ring from the aftermarket radio.
4. Slide the radio into the radio bracket
assembly and secure with screws
supplied with the radio. (Figure C)
Continue to Axxess Interface
Installation
(Figure A) (Figure B) (Figure C)
1.800.221.0932
|
MetraOnline.com
4
(Figure A) (Figure B)
KIT ASSEMBLY
ISO DDIN radio provision
1. Attach the
radio brackets
to the
radio
trim panel with touchscreen
using the
(4) #8 x 3/8”
Phillips screws
supplied.
(Figure A)
2. Attach the
radio brackets
to the radio
using the screws supplied with the
radio. (Figure B)
Continue to Axxess Interface
Installation
REV. 11/30/2018 INST99-8163 5
AXXESS INTERFACE INSTALLATION
INTERFACE FEATURES
INTERFACE COMPONENTS
• Axxess interface (built into the touchscreen display)
• 8163 harness
• 16-pin harness with stripped leads
• 4-pin harness with yellow RCA jacks
• Airbag-indicator/hazard/passenger-seatbelt harness
• Female 3.5mm connector with stripped leads
• AX-AB-LX1, AX-AB-LX2 and AX-AB-LX3 amplifier bypass harness (1 of each)
TOOLS REQUIRED
• Crimping tool and connectors, or solder gun, solder, and heat shrink
• Tape • Wire cutter • Zip ties
TABLE OF CONTENTS
Connections ................................................................................................................................6-7
Installation .................................................................................................................................... 8
Programming ................................................................................................................................ 9
Final assembly .............................................................................................................................. 9
Touchscreen display operation ...............................................................................................10-11
Steering wheel control settings .............................................................................................12-13
• Provides accessory power (12-volt 10-amp)
• Retains R.A.P. (retained accessory power)
• Provides NAV outputs (parking brake, reverse, speed sense)
• Retains audio controls on the steering wheel
• Retains the passenger airbag and seatbelt indicator
• Allows an aftermarket backup camera to be viewed on the 99-8163 display screen
• Retains the factory AUX-IN jack
• Micro-B USB updatable
1.800.221.0932
|
MetraOnline.com
6
CONNECTIONS
From the 16-pin harness with stripped leads to the aftermarket radio:
• Connect the Red wire to the accessory wire.
Note: There will also be an accessory wire from the 8163 harness to connect as well.
The following (3) wires are only for multimedia/navigation radios that require these wires.
• Connect the Blue/Pink wire to the VSS/speed sense wire.
• Connect the Green/Purple wire to the reverse wire.
• Connect the Light Green wire to the parking brake wire.
• Tape off and disregard the following (11) wires, they will not be used in this application:
Blue/White, Brown, Gray, Gray/Black, Green, Green/Black, Orange/White, Purple,
Purple/Black, White, White/Black
From the 8163 harness to the aftermarket radio:
• Connect the Black wire to the ground wire.
• Connect the Yellow wire to the battery wire.
• Connect the Blue wire to the power antenna wire.
• Connect the Blue/White wire to the accessory wire.
• Connect the Red and White RCA jacks to the audio AUX-IN jacks from the aftermarket radio.
• Tape off and disregard the following (4) wires, they will not be used in this application:
White, White/Black, Gray, Gray/Black
• Use the appropriate amplifier bypass included with the kit to connect to the speakers,
following the instructions included with the amplifier bypass. Take note that there are
multiple speakers in the vehicle with varying impedance. An external amplifier(s) and either
active or passive crossovers will be required (not provided).
Continued on the next page
REV. 11/30/2018 INST99-8163 7
• Universal “2 or 3 wire” radio: Connect the steering wheel control wire, referred to as
Key-A or SWC-1, to the Brown wire from the connector. Then connect the remaining
steering wheel control wire, referred to as Key-B or SWC-2, to the Brown/White wire
from the connector. If the radio comes with a third wire for ground, disregard this wire.
Note: After the interface has been programmed to the vehicle, refer to the manual
provided with the radio for assigning the SWC buttons. Contact the radio Manufacturer
for more information.
• For all other radios: Connect the 3.5mm jack into the port on the radio designated for
an external steering wheel control interface. Refer to the manual provided with the
radio if in doubt as to where the 3.5mm jack goes to.
4-pin harness with yellow RCA jacks:
• If an aftermarket backup camera is desired to be displayed onto the touchscreen display,
connect the Yellow RCA jack labeled “Rearview camera”, to the Yellow RCA jack.
• Disregard the Yellow RCA jack labeled “AUX video”, it will not be used in this application.
3.5mm jack steering wheel control retention:
The 3.5mm jack is to be used to retain audio controls on the steering wheel control.
• For the radios listed below: Connect the
female 3.5mm connector with stripped leads
to the
male 3.5mm SWC jack from the
8163 harness
. Any remaining wires tape off and disregard:
• Eclipse: Connect the steering wheel control wire, normally Brown, to the Brown/White
wire of the connector. Then connect the remaining steering wheel control wire, normally
Brown/White, to the Brown wire of the connector.
• Metra OE: Connect the steering wheel control Key 1 wire (Gray) to the Brown wire.
• Kenwood or select JVC with a steering wheel control wire: Connect the Blue/Yellow wire
to the Brown wire.
Note: If the Kenwood radio auto detects as a JVC, manually set the radio type to Kenwood.
Refer to the Select Radio screen.
• XITE: Connect the steering wheel control SWC-2 wire from the radio to the Brown wire.
• Parrot Asteroid Smart or Tablet: Connect the 3.5mm jack into the AX-SWC-PARROT
(sold separately), and then connect the 4-pin connector from the AX-SWC-PARROT into
the radio.
Note: The radio must be updated to rev. 2.1.4 or higher software.
CONNECTIONS (CONT.)
1.800.221.0932
|
MetraOnline.com
8
It is highly advisable to read the following steps beforehand, to ensure a clear understanding of
what is to be expected. The following steps must be done in the order that they are numbered.
With the vehicle completely off:
1. Connect the
16-pin harness with stripped leads
into port “B” in the touchscreen display.
2. Connect the
8163 harness
to the wiring harnesses in the vehicle. Then insert the
8163
harness
into port “A” in the touchscreen display. But do not install this harness until exactly
before step 1 from the Programming section. This is a timed process.
3. Connect the
4-pin harness with yellow RCA jacks
into port “C” in the touchscreen display.
4. Connect the
airbag-indicator/hazard/passenger-seatbelt harness:
a. Connect the harness to the 12-pin and 14-pin harnesses in the vehicle.
b. Connect the harness into the
airbag/seatbelt indicator.
c. Connect the harness into port “D” in the touchscreen display.
5. Disregard port “E”, it will not be used in this application.
6. Port “F” is an update port for future firmware upgrades.
7. Locate the factory antenna connector in the dash and complete all necessary connections
to the radio. Use the
antenna adapter
provided to adapt the factory antenna connector to
the aftermarket radio.
AB
C
E
FD
I N S TAL L ATI O N
Note: DO NOT CONNECT!
REV. 11/30/2018 INST99-8163 9
1. Secure the completed assembly into the dash using the factory hardware.
2. Reassemble the dash in reverse order of disassembly to complete the installation.
FINAL ASSEMBLYPROGRAMMING
Attention! If the interface loses power for any reason, the following steps will need to be
performed again.
1. Refer to step 2 from the “Installation” section.
2. Start the vehicle.
3. Program the kit:
a. Once the touchscreen display loads up, select the vehicle type; “Lexus IS”.
b. Wait until the radio comes on, and the touchscreen display shows “SWC Configured*”.
This process may take up to 3 minutes.
Note: If the touchscreen display does not load up, or the radio doesn’t come on within 3
minutes, and/or the touchscreen display does not show “SWC Configured*”, turn the vehicle
off and disconnect the 8163 harnesses from port “A” in the touchscreen display. Check all the
connections, reconnect the harness into the touchscreen display, and then try again.
4. Cycle the key off, then back on. If the driver’s door is closed, open and close the door.
5. Test all functions of the installation for proper operation, before reassembling the dash.
1.800.221.0932
|
MetraOnline.com
10
TOUCHSCREEN DISPLAY OPERATION
• This is the climate control screen which will be displayed on the touchscreen display.
This is considered the main screen.
• The upper right tab with the gear icon will take you to the Configuration Settings screen.
• The Dimmer button will control the illumination intensity: LOW/HIGH
• The climate controls will function in the same manner that they did with the factory
climate controls.
Continued on the next page
Climate Control Screen
Tabla de contenidos
Otros manuales de Receptor de coche de Metra Electronics
Metra Electronics
Metra Electronics 99-6543HG Manual de usuario
Metra Electronics
Metra Electronics 99-5700 Manual de usuario
Metra Electronics
Metra Electronics 95-7377B Manual de usuario
Metra Electronics
Metra Electronics 99-3010S-LC Manual de usuario
Metra Electronics
Metra Electronics 99-6527B Manual de usuario
Metra Electronics
Metra Electronics 99-7313 Manual de usuario
Metra Electronics
Metra Electronics 99-8249 Manual de usuario
Metra Electronics
Metra Electronics 99-6504 Manual de usuario
Metra Electronics
Metra Electronics AT-807HD Manual de usuario
Metra Electronics
Metra Electronics 99-7888 Manual de usuario
Metra Electronics
Metra Electronics 99-7382HG Manual de usuario
Metra Electronics
Metra Electronics 99-8270HG Manual de usuario
Metra Electronics
Metra Electronics 99-6519B Manual de usuario
Metra Electronics
Metra Electronics 99-5722 Manual de usuario
Metra Electronics
Metra Electronics 99-8209 Manual de usuario
Metra Electronics
Metra Electronics 95-7863 Manual de usuario
Metra Electronics
Metra Electronics 99-5825S Manual de usuario
Metra Electronics
Metra Electronics 99-5025 Manual de usuario
Metra Electronics
Metra Electronics 99-9013HG Manual de usuario
Metra Electronics
Metra Electronics 99-9604B Manual de usuario
