Metra Electronics 99-6536 Manual de usuario

INSTALLATION INSTRUCTIONS

99-6536

ATTENTION: With the key out of the ignition,

disconnect the negative battery terminal

before installing this product. Ensure that all

installation connections are secure before

cycling the ignition to test this product.

NOTE: Refer also to the instructions included

with the aftermarket radio.

KIT FEATURES

• ISO DIN radio provision with pocket

• ISO DDIN radio provision

• Retains audio controls on the steering wheel

• Retains the factory backup camera

•

Touchscreen display for climate and personalization features

•

Painted: Bronze - 99-6536BZ, Silver - 99-6536S

KIT COMPONENTS

• A) Radio trim panel with touchscreen display • B) Radio brackets • C) Pocket • D) #8 x 3/8" Phillips screws (4) • E) Panel clips (10)

• F) Wiring harness (not shown) • G) Antenna adapter (not shown)

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

• 9/32" Socket wrench • 5.5mm Socket wrench

TABLE OF CONTENTS

Dash Disassembly ..................................................2

Kit Preparation .......................................................3

Kit Assembly

–ISO DIN radio provision with pocket ..................4

–ISO DDIN radio provision .....................................4

Axxess Interface Installation ............................5-14

WIRING & ANTENNA CONNECTIONS

Wiring Harness: Axxess interface built into

touchscreen

Antenna Adapter: Included with kit

A B C D E

Jeep Grand Cherokee 2014-2017

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle

speciﬁc applications

2386.257.1187

MetraOnline.com

DASH DISASSEMBLY

1. Using the panel removal tool, gently

unclip, unplug, and remove the climate

control panel. (Figure A)

2. Remove (4) 9/32" screws securing

the radio/display screen, and then

unplug and remove. (Figure B)

3. Remove (3) 5.5mm screws securing

the black control module in the

sub-dash, and then relocate lower to

allow clearance for the aftermarket

radio. (Figure C)

Continue to Kit Preparation

(Figure B)

(Figure A)

(Figure C)

REV. 12/13/21 INST99-6536 3

KIT PREPARATION

(Figure A) (Figure B)

From the factory radio/climate control panel:

1. Unclip the A/C vents from the back of the

panel. (Figure A)

To the 99-6536 radio trim panel:

1. Attach the A/C vents to the back of the

panel. (Figure B)

2. Attach the (10)

panel clips

provided in

this kit to the clips on the back of the

panel.

Continue to Kit Assembly

4386.257.1187

MetraOnline.com

KIT ASSEMBLY

(Figure A)

(Figure B)

(Figure A)

ISO DIN radio provision with pocket

1. Attach the pocket to the radio brackets

using the (4) #8 x 3/8" Phillips screws

provided in this kit. (Figure A)

2. Remove the metal DIN sleeve and trim

ring from the aftermarket radio.

3. Slide the radio into the bracket/pocket

assembly, and then secure it using the

screws supplied with the radio.

(Figure B)

Continue to Axxess Interface Installation

ISO DDIN radio provision

1. Attach the radio brackets to the radio

using the screws supplied with the

radio. (Figure A)

2. Reconnect the negative battery terminal

and prepare for the Axxess interface

installation.

Continue to Axxess Interface Installation

REV. 12/13/21 INST99-6536 5

AXXESS INTERFACE INSTALLATION

INTERFACE FEATURES

• Provides accessory power (12-volt 10-amp)

• Retains R.A.P. (retained accessory power)

• Provides NAV outputs (parking brake, reverse, speed sense)

• Retains audio controls on the steering wheel

• Retains safety chimes

• Retains the factory backup camera

• Retains the factory AUX-IN jack

• Retains balance and fade*

• USB Micro-B updatable

* Non-ampliﬁed models only.

INTERFACE COMPONENTS

• Axxess interface (built into the touchscreen display)

• 6536 harness

• 16-pin harness with stripped leads

• 4-pin harness with yellow RCA jacks

• Hazard harness

• Female 3.5mm connector with stripped leads

TABLE OF CONTENTS

Connections

For Models

without

an Ampliﬁer ............................................................................................6

For Models

with

an Ampliﬁer. .................................................................................................7

3.5mm Jack Steering Wheel Control Retention .....................................................................8

Installation ....................................................................................................................................9

Programming ................................................................................................................................9

Final Assembly ..............................................................................................................................9

Touchscreen Display Operation .............................................................................................10-11

Steering Wheel Control Settings ...........................................................................................12-13

Troubleshooting .......................................................................................................................... 14

TOOLS REQUIRED

• Wire cutter

• Crimp tool and connectors (example: butt-connectors, bell caps, etc.)

• Solder gun, solder, and heat shrink

• Tape

• Zip-ties

• Small ﬂat-blade screwdriver

386.257.1187

MetraOnline.com

CONNECTIONS

From the 6536 harness to the aftermarket radio, connect as indicated:

• Black wire to the ground wire.

• Yellow wire to the battery wire.

• Gray wire to the right front (+) speaker output.

• Gray/Black wire to the right front (-) speaker output.

• White wire to the left front (+) speaker output.

• White/Black wire to the left front (-)speaker output.

• The 4-pin connector from the 6536 harness to the 4-pin harness with Yellow RCA jacks.

• Yellow RCA jacks to the reverse camera input. (if retaining the factory backup camera)

• Red and White RCA jacks to the audio AUX-IN jacks of the aftermarket radio.

(if using the AUX-IN jack in the dash)

Note: Disregard the DIN jack, it will not be used in this application.

Continue to 3.5mm jack steering wheel control retention

Attention! This interface will work with models that are either non-ampliﬁed, or ampliﬁed.

Please follow the instructions carefully for your model vehicle. Failure to do so will result in

either no sound, or low sound. If you are unsure if your vehicle is factory ampliﬁed or not,

please contact your local dealership.

For Models

Without

a Factory Ampliﬁer:

From the 16-pin harness with stripped leads to the aftermarket radio, connect as indicated:

• Red wire to the accessory wire.

• Orange/White wire to the illumination wire. (if applicable)

• Green wire to the left rear (+) speaker output.

• Green/Black wire to the left rear (-)speaker output.

• Purple wire to the right rear (+) speaker output.

• Purple/Black wire to the right rear (-)output.

Tape off and disregard the following (6)wires, they will not be used in this application:

Blue/White, Brown, Gray, Gray/Black, White, White/Black

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Blue/Pink wire to the VSS/speed sense wire.

• Green/Purple wire to the reverse wire.

• Light Green wire to the parking brake wire.

REV. 12/13/21 INST99-6536 7

CONNECTIONS (CONT.)

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Blue/Pink wire to the VSS/speed sense wire.

• Green/Purple wire to the reverse wire.

• Light Green wire to the parking brake wire.

From the 6536 harness to the aftermarket radio:

• Black wire to the ground wire.

• Yellow wire to the battery wire.

Tape off and disregard the following (4) wires, they will not be used in this application:

Gray, Gray/Black, White, White/Black

• The 4-pin connector from the 6536 harness to the 4-pin harness with Yellow RCA jacks.

• Yellow RCA jacks to the reverse camera input. (if retaining the factory backup camera)

• Red and White RCA jacks to the audio AUX-IN jacks of the aftermarket radio.

(if using the AUX-IN jack in the dash)

Note: Disregard the DIN jack, it will not be used in this application.

Continue to 3.5mm jack steering wheel control retention

Attention! This interface will work with models that are either non-ampliﬁed, or ampliﬁed.

Please follow the instructions carefully for your model vehicle. Failure to do so will result in

either no sound, or low sound. If you are unsure if your vehicle is factory ampliﬁed or not,

please contact your local dealership.

For Models

With

a Factory Ampliﬁer:

From the 16-pin harness with stripped leads to the aftermarket radio, connect as indicated:

• Red wire to the accessory wire.

• Blue/White wire to the amp turn on wire.

Note: This wire must be connected to hear sound from the factory ampliﬁer.

• Orange/White wire to the illumination wire. (if applicable)

• Gray wire to the right front (+) speaker output.

• Gray/Black wire to the right front (-)speaker output.

• White wire to the left front (+) speaker output.

• White/Black wire to the left front (-)speaker output.

• Green wire to the left rear (+) speaker output.

• Green/Black wire to the left rear (-)speaker output.

• Purple wire to the right rear (+) speaker output.

• Purple/Black wire to the right rear (-)output.

Tape off and disregard the following (1) wire, it will not be used in this application:

Brown

386.257.1187

MetraOnline.com

4-pin harness with yellow RCA jacks:

• If retaining the factory backup camera to the touchscreen display is desired,

connect the Yellow RCA jack labeled “Rearview camera”, to the Yellow RCA jack

from the

6536 harness

Note: If this method is chosen, the backup camera option must be enabled in

the Settings

screen

• Disregard the Yellow RCA jack labeled “AUX video”, it will not be used in this

application.

CONNECTIONS (CONT.)

3.5mm jack steering wheel control retention:

The 3.5mm jack is to be used to retain audio controls on the steering wheel.

•

For the radios listed below: Connect the

female 3.5mm connector with stripped leads

to the

male 3.5mm SWC jack from the 6536 harness. Any remaining wires tape off and disregard.

•

Eclipse: Connect the steering wheel control wire, normally Brown, to the Brown/White

wire from the connector. Then connect the remaining steering wheel control wire,

normally Brown/White, to the Brown wire from the connector

•

Metra OE:

Connect the Gray steering wheel control wire (Key 1) to the Brown wire.

•

Kenwood or select JVC with a steering wheel control wire:

Connect the

Blue/Yellow

wire to the

Brown

wire.

Note:

If your Kenwood radio auto detects as a JVC, manually set the radio type to

Kenwood. See the instructions under changing radio type.

•

XITE:

Connect the steering wheel control SWC-2 wire from the radio to the

Brown

wire.

•

Parrot Asteroid Smart or Tablet:

Connect the 3.5mm jack into the AX-SWC-PARROT (sold

separately), and then connect the 4-pin connector from the AX-SWC-PARROT into the

radio.

Note:

The radio must be updated to rev. 2.1.4 or higher software.

•

Universal “2 or 3 wire” radio:

Connect the steering wheel control wire, referred to as

Key-A or SWC-1, to the

Brown

wire from the connector. Then connect the remaining

steering wheel control wire, referred to as Key-B or SWC-2, to the

Brown/White

wire

from the connector. If the radio comes with a third wire for ground, disregard this wire

Note:

After the interface has been programmed to the vehicle, refer to the manual

provided with the radio for assigning the SWC buttons. Contact the radio manufacturer

for more information.

• For all other radios: Connect the 3.5mm jack from the 6536 harness to the jack on the

aftermarket radio designated for an external steering wheel control interface. Please refer

to the aftermarket radio’s manual, if in doubt as to where the 3.5mm jack connects.

REV. 12/13/21 INST99-6536 9

ATTENTION: It is highly advisable to read the following steps beforehand, to ensure a clear

understanding of what is to be expected. The following steps must be done in the order that

they are numbered.

With the vehicle completely off:

1. Locate the factory antenna connector in the dash and complete all necessary connections

to the radio. Use the antenna adapter provided to adapt the factory antenna connector to

the aftermarket radio.

2. Connect the

16-pin harness with stripped leads

into port “B” in the touchscreen display.

3. Connect the

4-pin harness with yellow RCA jacks

into port “C” of the touchscreen display.

4. Connect the

hazard harness

into port “D” of the touchscreen display, and then to the

designated wiring harness in the vehicle.

Note: Ensure to plug in the 8-pin connector from the climate control, using the wrong

connector will jam the CANBUS.

5. Disregard port “E”, it will not be used in this application.

6. Port “F” is an update port for future ﬁrmware upgrades.

1. Connect the

6536 harness

to the wiring harnesses in the vehicle. Then insert the

6536 harness

into port “A” in the touchscreen display.

Note: This is a timed process.

2. Press the push-to-start button to start the vehicle.

3. Program the Axxess interface built into the touchscreen display:

a. Once the touchscreen display loads up, select the vehicle type.

b. Wait until the radio comes on, and the touchscreen display shows SWC Conﬁgured.

This process may take up to (3) minutes.

Note: If the touchscreen display does not load up, or the radio doesn’t come on within (3)

minutes, and/or the touchscreen display does not show SWC Conﬁgured, turn the vehicle off

and disconnect the

6536 harnesse

s from port “A” in the touchscreen display. Check all the

connections, reconnect the harness into the touchscreen display, and then try again.

4. Cycle the key off, then back on. If the driver’s door is closed, open and close the door.

Refer to the Settings page within the Touchscreen Display Operation section. Ensure that all

factory features have been selected properly according to the options available for the vehicle

6. Test all functions of the installation for proper operation, before reassembling the dash.

Note: The clock and compass in the driver’s information center will no longer be functional.

1. Mount the completed radio/climate control assembly in the dash using the screws supplied

with the factory radio.

2. Snap the radio trim panel with touchscreen display over the completed assembly, and then

reassemble the dash in reverse order of disassembly.

FINAL ASSEMBLY

I N S TAL L ATI O N PROGRAMMING

Note: DO NOT CONNECT!

386.257.1187

MetraOnline.com

• This is the climate control screen which will be displayed on the touchscreen display.

This is considered the Main Menu screen.

• The upper left tab with (3) arrows will take you to the Heated/Cooled Seats* screen,

Heated Steering* screen, Mirror Dimming* screen, and also to the screen where the

hard buttons that were on the factory radio panel are now placed.

• The upper right tab with a gear icon will take you to the Settings screen.

• The climate controls will function in the same manner that they did with the factory

climate controls.

• For models with rear climate controls, the button labeled REAR will take you to the

rear climate control menu.

* If applicable.

• This is the Heated/Cooled Seats, Heated Steering, and Mirror Dimming screen which will be

displayed on the touchscreen display.

• The upper left-middle tab with a home icon will take you back to the Main Menu screen.

•

The upper right-middle tab with a gear icon will take you to the Settings screen.

• The upper right tab with a car icon will take you to the screen where the hard buttons that

were on the factory radio panel are now placed.

Continued on the next page

Climate Control screen Heated/Cooled Seats screen

TOUCHSCREEN DISPLAY OPERATION

Otros manuales para 99-6536

Tabla de contenidos

Otros manuales de Accesorios para automóviles de Metra Electronics

Metra Electronics

Metra Electronics 95-9313B Manual de usuario

Metra Electronics

Metra Electronics 99-3306 Manual de usuario

Metra Electronics

Metra Electronics LEXUS 99-8156 Manual de usuario

Metra Electronics

Metra Electronics 70-1727 Manual de usuario

Metra Electronics

Metra Electronics 99-9105 Manual de usuario

Metra Electronics

Metra Electronics 99-9303 Manual de usuario

Metra Electronics

Metra Electronics 95-7951 Manual de usuario

Metra Electronics

Metra Electronics AW-200GM Manual de usuario

Metra Electronics

Metra Electronics 95-7329 Manual de usuario

Metra Electronics

Metra Electronics 99-8206 Manual de usuario

Metra Electronics

Metra Electronics 107-FD1B Manual de usuario

Metra Electronics

Metra Electronics TYTO-01 Manual de usuario

Metra Electronics

Metra Electronics 107-TO1HG Manual de usuario

Metra Electronics

Metra Electronics 99-8152 Manual de usuario

Metra Electronics

Metra Electronics 99-7318 Manual de usuario

Metra Electronics

Metra Electronics 95-7337B Manual de usuario

Metra Electronics

Metra Electronics 99-9223 Manual de usuario

Metra Electronics

Metra Electronics 99-3106 Manual de usuario

Metra Electronics

Metra Electronics 99-7477 Manual de usuario

Metra Electronics

Metra Electronics 99-3400 Manual de usuario

Metra Electronics

Metra Electronics 95-8903B Manual de usuario

Metra Electronics

Metra Electronics 99-1008 Manual de usuario

Metra Electronics

Metra Electronics 95-6549 Manual de usuario

Metra Electronics

Metra Electronics 99-8715 Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario