Metal Defender MD-1 Manual de usuario

MD-1

User Manual

Contact

772 Twin Rail Drive

Minooka, IL 60447

Phone: (815) 467-6464

Email: sales@metaldefender.com

Website: www.metaldefender.com

MEDICAL SAFETY

Metal Defender makes every effort to ensure its products are safe for use. Extensive

research by Metal Defender has produced no information which would indicate that its

products have any adverse effects on medical implants, pregnancy, recording media or

magnetic strips. Metal Defender makes every effort to cooperate with medical device

manufacturers and to communicate with agencies such as the United States Food and Drug

Administration and Health Canada as a means of assuring product safety. The

electromagnetic fields produced by Metal Defender products are similar to those

encountered in the daily environment and meet U.S. and International standards for

electromagnetic emissions.

Metal Defender recognizes that certain medical devices may have additional requirements

which may require special care. Any recommendations or directives issued by personal

physicians or medical device manufacturers should be followed. If, for any reason, (e.g.

doctors orders, etc.), a patron objects to being scanned with a metal detector, it is

recommended that alternative procedures be used.

The following should be considered when developing a security checkpoint screening plan.

• Traffic Flow - Traffic flow should remain consistent and encourage unrestricted traffic

flow as a means of minimizing the time a person remains within the archway of a walk-

through metal detector.

• Alternative Screening - Alternative screening methods such as scanning with a handheld

metal detector, hand searching or denial of access should be clearly defined in checkpoint

screening procedures as approved alternatives to screening with the walk- through metal

detector.

• Personnel Training - Security screening personnel should be instructed in the care of

persons with special medical needs and use of alternative screening methods that meet the

requirements of medical practitioners or medical device manufacturers.

Index

Medical Safety –pg.2

Product Description –pg.5

Product Performance –pg.5

Introduction of Components –pg.6

Installation Instructions –pg.7

Description of Display Panel –pg.8

Operation Procedures –pg.8

Adjustment of Object Detection –pg.9

Interference Description –pg.9-10

Precautions –pg.10

Common Faults & Solutions –pg. 11

Technical Specifications –pg.12

FAQ –pg.13-14

Suggested Single Lane Configuration –pg.14

Suggested Multi Lane Configuration –pg.15

Warranty Information –pg.16

Replacement Parts –pg.17

1. Please assemble and deploy on a flat, vibration-free surface in order to avoid false alarms

caused by shaking the security gate.

2. Wait 1 minute after you turn on the metal detector in order to get the best detection

results.

3. Please make sure that people walk through the unit at the standby time or alarm time

setting (Preset at 1 second), and pass one by one. Do not crowd around the gate, it may

cause interference with the infrared sensors. Patrons should pass through one at a time

and allow a minimum of 1 second after the person walks through.

4. Do not hit or collide with the gate, if this happens there will be a false alarm.

5. If the unit gets dirty, wipe it gently with a cloth dipped in water or alcohol. Do not use

other chemicals.

6. Each unit has a 2 year warranty.

Product Description

The MD-1 is a single zone walk thru metal detector with only one changeable zone. This

metal detector is only recommended when individuals passing through are eliminating all

portions of metal on their entire body. Due to this unit only having one zone, determining

or pin pointing the exact location of the metal can be difficult that is why we all suggest

having an on staff security screener administrating the unit. The one zone on the MD-100s

is adjustable in terms of sensitivity. Users can dial the sensitivity to their desired settings

based on the type of metal they wish to detect.

Product Performance (also use teq Speqs)

Alarming mode: sound and light alarm, pitch's frequency is used to indicate the size of

metal object, a variety of alarm volume modes is available for different occasions.

Detection sensitivity: the highest sensitivity can detect the metal objects of paper clip's

size, each zone's adjuster can be adjusted to the appropriate sensitivity according to the

detection requirements of such zone, and meanwhile, the overall sensitivity can be

separately adjusted. The pre-setting of metal objects' weight, volume, size and location can

exclude the false alarm caused by key, jewelry, belt buckle and other objects.

Appearance process: it is made of PVC synthetic materials and special manufacturing

process; it is featured by luxury and beautiful appearance and suitable for large-scale and

high-end locations.

Intelligent statistics: Intelligent passengers and alarms counting function that can

automatically count the number of passengers and alarms.

Strong anti-interference ability: it adopts digital, analog, left and right balance technologies

to prevent false and omission alarms, and greatly improves the anti-interference capability.

Electromagnetic radiation: it complies with EMC's electromagnetic radiation standard; its

weak magnetic field technology is harmless to pacemaker user, pregnant women, floppy

disks, film rolls, videotapes, etc.

Installation & commissioning: this series of metal detection doors uses integrated design, it

only takes 20 minutes to complete installation or disassembly, installation and

commissioning instruction will be delivered with product.

Introduction of Components

1. Main board

2. Panel

3. Built-in infrared sensor probe

4. Infrared sensor

5. Waterproof feet

6. Power socket

Installation Instructions

1. Open the carton, take objects out from the packaging, and placed them on the foam

board according to the following figure:

2. Place the main case with its display panel facing up, after you properly place the

components, open main case's lower panel with key, fix the left and right panels on the

main case with screws.

3. Insert the signal cable into the signal cable interface, and then lock the main case.

4. After all the objects are fixed; two persons erect it to the vertical position, then connect

the power using power cable and enter the starting and self-inspection status.

Description of Display Panel

Number of passengers: Counting of personnel walking through the security door

Number of alarms: Counting of security door's alarming times

Counting board (8 digital LED tubes): The left four LEDs indicate the number of passengers,

the right four LEDs indicate the number of alarms, for the indication meaning of settings,

please check operation procedures.

Strength indication: When the metal is detected, the bigger the signal is, the more the

lamps are turned on

Sensitivity: Higher sensitivity is used to detect the small metal objects; lower sensitivity is

used to detect the big metal objects.

Volume: Alarm's sound volume.

Operation Procedures

The security door of this model is easy to operate, press the program key to enter

sensitivity adjustment mode, use upper and lower keys to select required sensitivity,

adjustable between (0-99); then press the program key again to enter frequency selection

mode, use upper and lower keys to select required frequency, adjustable between 1-12.

Adjustment of Object Detection

How to exclude small pieces of metal and detect large pieces of metal?

During the inspection of metal objects carried by people, we do not want to detect small

pieces of metal objects such as rings, keys, etc., and need to detect large pieces of metal;

you can adjust the product according to the following methods:

1. Select a small metal as sample; the sample will be used as the boundary for that we do

not want to detect, such as a bunch of keys.

2. Increase the sensitivity, let metal sample pass through the security door and trigger

alarm.

3. Appropriately decrease the sensitivity, let the sample pass through the detection door

again, if it still send alarms, reduce the sensitivity again until the sample will slightly lower

than the alarm triggering threshold.

After the above adjustment, the metals that are smaller than the sample will not trigger the

alarm and those are bigger than the sample can be accurately detected.

When the person to be inspected passes through the security door, if alarm sound is

triggered, which means that he has hidden metal objects on himself, if you want to

determine the exact location of metal objects and find it, you can purchase the hand-held

metal detector produced by our company.

Interference Description

The following interference may happen during the operation of metal detection door:

Mechanical interference

Revolving door: the distance between detector and revolving door should be 1000 mm.

Make sure that revolving door is open outward. If there has two doors, then the detection

door should be installed on one of them, we recommend that you have to lock another

door. If it is a metal door, we recommend cutting the corner of metal door's frame to

isolate its metal ring. After the detector is installed, turn the revolving door back and forth

to check the performance of installed metal detection door.

Electronic interference

There are many objects that can cause electronic interference to metal detection door,

such as elevators, engines, televisions, computers, telephone lines, mobile phones, and so

on. These objects should be kept away from metal detection door; consult your dealer if

there has continuous serious interference.

Moving objects

If the installation location of metal detection door is too close to road, large vehicles

passing by may affect its normal operation. Therefore, we recommend that the installation

of metal detection door shall be as far away from the roadside as possible.

Parallel connection requirements

For parallel application, the minimum distance between two doors should be at least

700mm to avoid mutual interference between two metal detection doors

Precautions

1. This product is only suitable for indoor use, if it needs to be installed outdoor, please

select waterproof products or install rain shelters and other weather proof facilities.

2. There shall not have any large metal and strong magnetic field within 2 meters around

the detection door to avoid interference. If the door near the installation site is metal door,

the distance between metal detection door and metal door must be at least 500 mm

(depending on the size of metal door).

3. Detection door shall not be installed in a high temperature, humid environment.

4. Non-professionals are not allowed to disassemble or maintain the security door.

5. Detection door achieves the best detection status within 1-2 minutes after starting.

6. The detection door should be installed on smooth and vibration-free ground; people shall

avoid collision when passing through the door.

7. Each metal detection door is provided with a warranty, it can receive the free repair

service during the warranty period.

8. This manual is applicable for LED walk through metal detection door - single zone

version, the appearance of security door purchased by you may not be inconsistent with

the appearance described in this manual, but which will not affect your operation and use.

Tabla de contenidos

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario