Memotec CX800 Guía rápida de usuario

CX800 Hardware

Reference Manual

Part # 3023M100-004

Date: April 2000

PROPRIETARY NOTICE

This publication contains information proprietary and confidential to Memotec Communications Inc.

Any reproduction, disclosure or unauthorized use of this publication is expressly prohibited except as

Memotec Communications Inc. may otherwise authorize in writing.

Memotec Communications Inc. reserves the right to make changes without notice in product or com

ponent design as warranted by evolution in user needs or progress in engineering or manufacturing

technology. Changes which affect the operation of the unit will be documented in the next revision of

the manual.

Printed in Canada

Memotec Communications Inc.

600 McCaffrey Street,

Montreal, Quebec

CANADA H4T 1N1

Tel.: (514) 738-4781

FAX:(514) 738-4436

Web Site: http://www.memotec.com

WARRANT

Memotec warrants each new Product sold by Memotec will be free from defective material and workmanship.

Memotec agrees to remedy in accordance with terms specified below any such defect which is disclosed under condi-

tions of normal installation, use and service. To exercise the warranty the Distributor/ Business Partner or any person

or corporation which purchases such Product from the Distributor/Business Partner ("end-user") must deliver the

product intact for examination, with all transportation charges prepaid, to the facility designated by Memotec.

The specific terms of the warranty are as follows:

1. The warranty period commences on the date the unit is shipped by Memotec;

2. The warranty applies to the Distributor/Business Partner, provided however, that when Distributor/

Business Partner resells any Products, pursuant to its rights hereunder, the said warranty shall apply

to any end-users which purchase such Products from Distributor/Business Partner;

3. Memotec will be responsible for both material and labour required to effect all repairs under terms of

the warranty for a warranty period of twelve (12) months(North America), fifteen (15) months (Inter-

national), from the date of shipment of the Product by Memotec, providing the unit is returned to

Memotec as specified above; and

4. During the warranty period, the Distributor/Business Partner or end-user may return defective parts

for replacement at no charge, in lieu of returning the complete Product.

This warranty does not apply if:

1. the Producthas been modified by the Distributor/BusinessPartner or end-user orsubjected to misuse,

neglect, or accident, or

2. the Product has been repaired or altered by an unauthorized service depot so that its performance or

reliability has been impaired, or

3. the Product has had the serial number altered, effaced or removed, or

4. the Product has been damaged by accessories peripherals, and/or other attachments not approved by

Memotec.

Software is warranted to substantially conform to Memotec’s specifications for a period of ninety (90) days from the

date of delivery. Memotec’s sole obligation under this warranty shall be limited to using its best efforts to correct

such Software as soon as practical after Distributor/Business Partner or end-user has notified Memotec of such

defects. Memotec does not warrant that operation of any of the Software shall be uninterrupted or error-free or that

functions contained in the licensed Software shall operate in combinations which may be selected for use by the Dis-

tributor’s/Business Partner or end-user or meet the Distributor’s/Business Partner’s or end-user’s requirements. No

warranty shall apply to any Software that is modified without Memotec’s written consent.

This warranty is in lieu of all other warranties, expressed or implied and no representative or person is authorized to

assume for Memotec any other liability in connection with the sale of the Product and Software.

IN NO EVENT SHALL MEMOTEC BE LIABLE, WHETHER IN CONTRACT OR INTORT OR ON ANY

OTHER BASIS, FOR ANY DAMAGES SUSTAINED BY THE DISTRIBUTOR/ BUSINESS PARTNER OR ANY

OTHER PERSON ARISING FROM ORRELATED TO LOSS OF USE, FAILURE OR INTERRUPTION IN

OPERATION OF ANY PRODUCTS,OR DELAY IN MAINTENANCE OR FOR INCIDENTAL, CONSEQUEN-

TIAL, INDIRECT OR SPECIAL DAMAGES OR LIABILITIES, OR FOR LOSS OF REVENUE, LOSS OF BUSI-

NESS OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, LEASE,

MAINTENANCE, USE PERFORMANCE, FAILURE OR INTERRUPTION OF THE PRODUCTS.

FEDERAL COMMUNICATIONS COMMISSION

(FCC) NOTIFICATIONS

Part 15 Advisements: This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his

own expense.

Changes or modifications not expressly approved by Memotec Communications Inc.

could void the users authority to operate the equipment.

Shielded cables must be used for the serial port line interface drivers to ensure

continued compliance with FCC emission requirements. All cables are available fro

Memotec Communications Inc.

Part 68 Advisements: The CX800 complies with Part 68 of the FCC Rules. The FCC registration number

and ringer equivalence (REN) are indicated below and on the label attached to the

bottom of the chassis. Upon request, the user shall provide the FCC registration

number and ringer equivalence to the telephone company.

FCC Registration No.: 2PDCAN-25867-OT-E

Ringer Equivalence (REN): 0.0A

Service Order Code: 9.0F

USOC Jack: RJ11C

Facility Interface Code: 02LS2

This equipment is designed to be connected to a telephone network or premises

wiring using a cable with a compatible plug and modular jack which are FCC Part 68-

compliant. See installation instructions (in this manual) for details on hardware

connection.

The sum of the RENs for the equipment determines the number of devices that you

may connect to the telephone line. If the quantity of devices on the telephone line

demands too many RENs, then the equipment may fail to ring in response to an

incoming call. In most areas (but not all), the sum of RENs should not exceed five. To

be certain of the number of devices that should be connected to a line, contact the

local telephone company.

If the CX800 should cause harm to the telephone network, the telephone company

will notify you (the customer) in advance (as soon as is practical or possible) that

temporary discontinuance of service may be required. Also, you will be advised of

your right to file a complaint with the FCC if you believe it is warranted.

The telephone company may make changes in its facilities, equipment, operations or

procedures that could affect the operation of the CX800. If this happens, the

telephone company will provide advance notice in order for you to make necessary

modifications to maintain uninterrupted service.

If you encounter problems or have trouble with the CX800 and require service or

warranty information, please contact:

Memotec Communications Inc.

1-800-766-7782

If problems arise such that the CX800causes harm to the telephone network, the

telephone company may request that you disconnect the equipment until the proble

is resolved.

The CX800 cannot be used on public coin phone service provided by the telephone

company. Connection to party line service is subject to state tariffs. Contact the state

public utility commission, public service commission or corporation commission for

additional information.

INDUSTRY CANADA (IC) NOTIFICATIONS

CP-01 Advisements: NOTICE: The Industry Canada label identifies certified equipment. This certification

means that the equipment meets certain telecommunications network protective,

operational and safety requirements. Industry Canada does not guarantee the

equipment will operate to the users satisfaction.

Before installing this equipment, users should ensure that it is permissible to be

connected to the facilities of the local telecommunications company. The equipment

must also be installed using an acceptable method of connection. The customer

should be aware that compliance with the above conditions may not prevent

degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian

maintenance facility designated by the supplier. Any repairs or alterations made by

the user to this equipment, or equipment malfunctions, may give the

telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of

the power utility, telephone lines and internal metallic water pipe system, if present,

are connected together. This precaution may be particularly important in rural areas.

CAUTION: Users should not attempt to make such connections themselves, but

should contact the appropriate electrical inspection authority, or electrician, a

appropriate.

The Ringer Equivalence Number (REN) assigned to each terminal device provides an

indication of the maximum number of terminals allowed to be connected to a

telephone interface. The termination on an interface may consist of any combination

of devices subject only to the requirement that the sum of the RENs of all the devices

does not exceed 5. The REN for the CX800is 0.0A.

ICES-003 Advisements: This class A digital apparatus meets all requirements of the Canadian interference-

causing equipment regulations. Shielded cables must be used for the serial port line

interface drivers to ensure continued compliance with emission requirements. All

cables are available from Memotec Communications Inc.

Directive PH-01: AVIS: L’étiquette d’Industrie Canada identifie le matériel homologué. Cette

étiquette certifie que le matériel est conforme à certaines normes de protection,

d’exploitation et de sécurité des réseaux de télécommunications. Industrie Canada

n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur.

Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le

raccorder aux installations de l’entreprise locale de télécommunications. Le matériel

doit également être installé en suivant une méthode acceptée de raccordement.

L’abonné ne doit pas oublier qu’il est possible que la conformité aux conditions

énoncées ci-dessus n’empêche pas la dégradation du service dans certaines situations.

Les réparations de matériel homologué doivent être effectuées par un centre

d’entretien canadien autorisé désigné par le fournisseur. La compagnie de

télécommunications peut demander à l’utilisateur de débrancher un appareil à la suite

de réparations ou de modifications effectuées par l’utilisateur ou en raison d’un

mauvais fonctionnement.

Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la terre

de la source d’énergie électrique, les lignes téléphoniques et les canalisations d’eau

métalliques, s’il y en a, sont raccordés ensemble. Cette précaution est particulière-

ment importante dans les régions rurales.

AVERTISSEMENT: L’utilisateur ne doit pas tenter de faire ces raccordements lui-

même; il doit avoir recours à un service d’inspection des installations électriques, ou à

un électricien, selon le cas.

AVIS: L’indice d’équivalence de la sonnerie (IES) assigné à chaque dispositif termi-

nal indique le nombre maximal de terminaux qui peuvent être raccordés à une inter-

face. La terminaison d’une interface téléphonique peut consister en une combinaison

de quelques dispositifs, à la seule condition que la somme d’indices d’équivalences

de la sonnerie de tous les dispositifs n’excède pas 5. L’indice d’équivalence de la

sonnerie (IES) pour le CX800 est de 0.0A.

Directive NMB-003: Cet appareil numérique de la classe A respecte toutes les exigences du règlement sur

le matériel brouilleur du Canada. Des câbles blindés doivent être utilisés pour les

interfaces de jonction au port série afin de respecter les normes d’émission. Ces

câbles sont disponibles chez Memotec Communications inc.

CONFORMITY MARKINGS FOR EUROPEAN

UNION (EU) DIRECTIVES

Several or all of the following markings may be located on CX800 products.

This marking on the chassis identifies the CX800 as fully compliant with the require-

ments of the European LowVoltage (safety) Directive (or LVD), number 73/23/EEC

and the European EMC Directive, number 89/336/EEC (and amendments that apply

to both directives).

This marking on the chassis identifies the CX800 chassis as fully compliant with the

requirements of the European Telecommunication Terminal Directive, number 91/

263/EEC (and amendments) and continued compliance with the LVD and EMC

Directives mentioned above. The approved interfaces are FXO, X.21, V.24, andV.35.

The FXO has been approved in accordance with Council Decision 98/482/EC for

pan-European single terminal connection to the public switched telephone network

(PSTN). However, due to differences between the individual PSTNs provided in dif-

ferent countries, the approval does not, of itself, give an unconditional assurance of

successful operation on every PSTN network termination point.

In the event of problems, you should contact your equipment supplier in the first

instance.

This marking identifies certain interfaces in the CX800 that are not approved for con-

nection to PTO-provided networks. Such interfaces are for private or internal use

only

This marking on the chassis identifies the CX800 voice I/O as fully compliant with

the requirements of all applicable ACA Telecommunications and EMC standards.

This marking on the chassis identifies the CX800 as fully compliant with applicable

Australian EMC requirements.

Inherent delays in packet-switched technology prevent the CX800 from meeting

certain Standard Telephone Service requirements as defined by the

Telecommunications Act 1997. For this reason, it is recommended that local outgoing

calls should not be routed through the CX800 system.

NOTE: This equipment will be inoperable when mains power fails.

An FXS port must not be connected to non-switched lines of the telecommunication

network (leased lines). All devices connected to an FXS port must be colocated with

the CX800 system. Furthermore, intra-building connections to an FXS port must not

share the same cable sheath as cabling carrying Telecommunications Network

services. Such connections must either be separately routed or individually screened

(shielded).

NOTE: All cabling connected to telecommunications ports must be TS 008 compliant.

Tabla de contenidos

Otros manuales de Hardware de red de Memotec

Memotec

Memotec NetPerformer SDM-9220 Series Manual

Memotec

Memotec NetPerformer SDM-9120 Series Manual

Memotec

Memotec CX950 Guía rápida de usuario

Memotec

Memotec CX900e Guía rápida de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario