Mellanox Technologies Vantage 8500 Manual de usuario

www.mellanox.com

Mellanox VantageTM 8500 288 Port Switch

Installation Manual

OPN

Rev A04

Mellanox Technologies

350 Oakmead Parkway Suite 100

Sunnyvale, CA 94085

U.S.A.

www.mellanox.com

Tel: (408) 970-3400

Fax: (408) 970-3403

Mellanox Technologies, Ltd.

PO Box 586 Hermon Building

Yokneam 20692

Israel

Tel: +972-4-909-7200

Fax: +972-4-959-3245

Mellanox®, BridgeX®, ConnectX®, InfiniBlast®, InfiniBridge®, InfiniHost®, InfiniRISC®, InfiniScale®,

InfiniPCI®, PhyX® and Virtual Protocol Interconnect® are registered trademarks of Mellanox Technologies, Ltd. CORE-

Direct and FabricIT are trademarks of Mellanox Technologies, Ltd. All other marks and names mentioned herein may be

trademarks of their respective companies.

Mellanox VantageTM 8500 288 Port Switch Installation Manual

Document Number: DOC-00651-A04

Rev A04

Mellanox Technologies

MELLANOX TECHNOLOGIES, INC. AND ITS AFFILIATES (“MELLANOX”) FURNISH THIS DOCUMENT

“AS IS,” WITHOUT WARRANTY OF ANY KIND. MELLANOX DISCLAIMS ALL WARRANTIES, EXPRESS OR

IMPLIED, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY,

FITNESS FOR A PARTICULAR PURPOSE, NON-INFRINGEMENT AND THOSE ARISING FROM A COURSE OF

PERFORMANCE, A COURSE OF DEALING, OR TRADE USAGE. MELLANOX SHALL NOT BE LIABLE FOR ANY

ERROR, OMISSION, DEFECT, DEFICIENCY OR NONCONFORMITY IN THIS DOCUMENT AND DISCLAIMS ALL

LIABILITY, INCLUDING LIABILITY FOR INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHTS

RELATED TO THE INFORMATION CONTAINED IN THIS DOCUMENT.

No license, expressed or implied, to any intellectual property rights is granted under this document. This document, as well as

the software described in it, are furnished under a separate license and shall only be used or copied in accordance with the

terms of the applicable license. The information in this document is furnished for informational use only, is subject to change

without notice, and should not be construed as any commitment by Mellanox. Except as permitted by the applicable license,

no part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means without

the express written consent of Mellanox.Names and logos identifying products of Mellanox in this document are registered

trademarks or trademarks of Mellanox. Voltaire is a registered trademark of Mellanox Technologies, Ltd. All other trademarks

mentioned in this document are the property of their respective owners.

Rev A04

Mellanox Technologies 3

Table of Contents

About this Manual 8

Intended Audience 10

Document Conventions 11

Textual Conventions 12

Related Documentation 13

Chapter 1 Product Overview 14

1.1 The Vantage 8500 Switch 14

1.2 PhysicalDescription 15

1.2.1 Chassis 15

1.2.2 Plug-in Modules - Overview 16

1.3 BlockDiagram 21

1.4 ProductOptions 21

1.4.1 Basic Hardware Configuration 22

1.4.2 Full Hardware Configuration 22

1.5 TechnicalSpecifications 24

1.5.1 Chassis 24

1.5.2 Line Boards (sLB-1024) 24

1.5.3 Fabric Boards (sFB-8500) 25

1.5.4 Management Board (sMBE) 25

1.5.5 Control Panel sCTRL 25

1.5.6 Fan Modules 25

1.5.7 Power Supply Unit (sPSU-S) 26

1.5.8 Power Supply Calculation Example 27

1.5.9 IEEE Compliance 27

1.5.10 Datacenter Bridging (CEE) 28

1.5.11 Layer-2 Capabilities 28

1.5.12 Physical/Electrical 28

1.5.13 Cooling 28

1.5.14 Physical Characteristics 28

1.5.15 Environmental 28

1.5.16 Acoustic Data 29

1.5.17 Certifications 29

1.6 Reliability(MTBF) Data 30

1.7 Declarations 30

1.7.1 Declaration of Conformity 30

1.7.2 Hazardous Substances (RoHS 6) Compliance 30

1.7.3 Statement of Volatility 31

1.8 Shock and Vibration Test Report 31

Chapter 2 Installation Requirements 33

2.1 SitePlanning 33

2.2 HeatDissipation 33

2.3 Rack and Clearance Requirements 33

2.4 PowerRequirements 34

2.4.1 sPSU-S Units - Power Usage/Requirements 34

2.4.2 Power Redundancy (N:1 and N:N) 35

2.5 Required 10GbE Cables and Port Adapters 36

2.6 Required Control and Management Cables 37

2.7 RequiredInstallationTool 38

Chapter 3 Unpacking 39

3.1 Packed Unit Dimensions and Weight 39

3.2 PackageContents 39

Rev A04

Mellanox Technologies

3.3 UnpackingtheSwitch 40

3.4 Center of Gravity Data 43

3.5 PackingforRe-Deployment 44

Chapter 4 Chassis Installation 45

4.1 MountingProcessSummary 45

4.1.1 Assembling and Mounting the Rails 45

4.1.2 Mounting the Chassis in the Rack 53

4.1.3 Installing Cabling Guide Brackets 56

4.2 Shipping Guidelines and Instructions 57

Chapter 5 Installing Modules 59

5.1 ChassisSlotNumbering 59

5.2 ModuleInsertionRules 59

5.3 Extracting/InsertingBoards 61

5.3.1 Installing a Fabric Board (sFB-8500) 63

5.3.2 Extracting a Fabric Board (sFB-8500) 63

5.3.3 Installing a Line Board (sLB-1024) 64

5.3.4 Extracting a Line Board (sLB-1024) 64

5.3.5 Installing a Management Board (sMBE) 65

5.3.6 Extracting a Management Board (sMBE) 66

5.4 Installing a Power Supply Unit (sPSU-S) 67

5.5 Extracting a Power Supply Unit (sPSU-S) 67

5.6 Replacing a Control Board (sCTRL) 68

5.7 Replacing Fan Units (sFUs) 69

5.8 Replacing the sFU-4 Unit 70

5.9 Replacing the sFU-8E Unit 70

Chapter 6 Connector and Cable Specifications 72

6.1 Cabling-Do'sand Don'ts 72

6.2 GeneralGuidelines 72

6.3 Connecting10GbECables 72

6.4 Connecting the Unit to a Local Management Terminal 73

Chapter 7 Final Checks, Operation and Troubleshooting 75

7.1 Required Checks Before Initial Operation 75

7.2 Powering-upthe Switch 75

7.3 Verifying Proper Switch Operation 75

7.4 Checking the LED Indicators 75

7.4.1 Line Board (sLB-1024) LED Indicators 76

7.4.2 Fabric Board (sFB-8500) LED Indicators 76

7.5 Power Supply Unit (sPSU-S) LED Indicators 77

7.5.1 Fan Unit LED Indicators 78

7.5.2 Management Board (sMBE) LED Indicators 78

7.5.3 Control Board (sCTRL) LED Indicators 79

Appendix A Port Pinouts 81

RJ-45 Management Port 82

DB-9 Serial Port 83

Rev A04

Mellanox Technologies 5

List of Figures

Figure 1: Vantage 8500 Switches in a Scale-Out Ethernet Configuration 14

Figure 2: Vantage 8500 Switch -Front View 15

Figure 3: Vantage 8500 Switch - 3D Rear View 16

Figure 4: Line Board (sLB-1024) 17

Figure 5: Fabric Board (sFB-8500) 18

Figure 6: Management Board (sMBE) 19

Figure 7: Power Supply Unit (sPSU-S) 19

Figure 8: Vertical Fan Unit (sFU-4) 20

Figure 9: Horizontal Fan Unit (sFU-8E) Front Panel 20

Figure 10: Control Board (sCTRL) Front Panel 21

Figure 11: Vantage 8500 Block Diagram 21

Figure 12: Vantage 8500 Switch -Front View 23

Figure 13: Vantage 8500 Rear View in Full Hardware Configuration 24

Figure 14: Fully Configured Switch at N:1 Power Redundancy 36

Figure 15: Unpacking Procedure for the Vantage 8500 Switch 40

Figure 16: Unpacking the Chassis 41

Figure 17: Chassis Partially Unpacked 42

Figure 18: Center of Gravity Data 43

Figure 19: sPSU-S Side Label on the Foam sPSU-S 44

Figure 20: Rail Kit Components - Left Bracket, Right Bracket, Screws, Washers and Nuts 46

Figure 21: Assembling the Rail Bracket and Insert 47

Figure 22: Positioning the Insert In Front of the Right Bracket 48

Figure 23: Assembling an Insert to a Rail Bracket (Inside View) 48

Figure 24: U Alignment 49

Figure 25: Above U Alignment 50

Figure 26: Mounting the Rail - Left Side Front and Rear View 50

Figure 27: Chassis Grounding Holes 52

Figure 28: Top Grounding Connection (Grounding Stud Installed) 52

Figure 29: Grounding Stud Installation 53

Figure 30: Mounting a Basic Vantage 8500 Switch Chassis in a Rack 55

Figure 31: Chassis Secured onto the Front Rack Rail 56

Figure 32: Cabling Guide Brackets 56

Figure 33: Screws, 3/8" Tooth Washer, and Flat Washers 57

Figure 34: Screws on Chassis Side Wall 58

Figure 35: Chassis Slot Numbering for sLB-1024 Modules 59

Rev A04

Mellanox Technologies

Figure 36: Fabric Board Slot Numbering 60

Figure 37: Using Ejectors to Extract a Board 62

Figure 38: Extracting an sFB-8500 Board 64

Figure 39: Extracting an sLB-1024 Board 65

Figure 40: Securing the sMBE Board 66

Figure 41: Extracting an sMBE Board 67

Figure 42: Extracting a sPSU-S Unit 68

Figure 43: Removing the sCTRL Board 69

Figure 44: Securing the sCTRL Board 69

Figure 45: Securing the sFU-4 Board 70

Figure 46: Removing the sFU-8E Unit 71

Figure 47: Securing the sFU-8E Unit 71

Figure 48: Line Board (sLB-1024) Front Panel 76

Figure 49: Fabric Board (sFB-8500) Front Panel 76

Figure 50: Power Supply Unit (sPSU-S) Front Panel 77

Figure 51: Horizontal Fan Unit (sFU-8E) Front Panel 78

Figure 52: Management Board (sMBE) Front Panel 79

Figure 53: Control Board (sCTRL) Front Panel 80

Rev A04

Mellanox Technologies 7

List of Tables

Table 1: Conventions 12

Table 2: Vantage 8500 Switch - Part Naming Conventions 16

Table 3: Vantage 8500 Switch Line Board Components 17

Table 4: Vantage 8500 Basic Hardware Configuration 22

Table 5: Vantage 8500 Full Hardware Configuration 22

Table 6: Power Calculation Table 27

Table 7: MTBF Information per Module 30

Table 8: Axes (X,Y,Z) Vibration Test for Transportation without a Rack 31

Table 9: Drop Tests 32

Table 10: Rack Clearance Requirements 34

Table 11: sPSU-S - Detailed Power Usage Data 35

Table 12: SFP+ Copper 10GbE Cables 36

Table 13: SFP+ Fiber Optic 10GbE Transceivers (Required for Fiber Optic Cables) 37

Table 14: Fiber Optic Cables (Require SFP+ Transceivers) 37

Table 15: Tools Required for Hardware Installation 38

Table 16: Factory-Packed Unit Weight and Dimensions 39

Table 17: Center of Gravity Data 43

Table 18: Fabric Board Insertion 59

Table 19: Line Board (sLB-1024) LED Indicators 76

Table 20: Fabric Board (sFB-8500) LED Indicators 77

Table 21: Power Supply Unit (sPSU-S) LED Indicators 78

Table 22: Fan Unit LED Indicators 78

Table 23: Management Board Indicators 79

Table 24: Control Board LED Indicators 80

Table 25: RJ-45 Management Port Pinout 82

Table 26: DB-9 RS-232 CLI Connector Pinout 83

Rev A04

Mellanox Technologies

About this Manual

This manual describes how to install the Vantage 8500.

Please refer to the official and latest product release notes for last-minute updates.

Technical support may be obtained directly from:

• Your regional distributor from whom this product was ordered

• Your OEM customer representative

For further information and assistance, go to http://www.Mellanox.com/support.htm.

We sometimes update the printed and electronic documentation after original publica-

tion. Therefore, review the documentation on http://www.Mellanox.com for any

updates.

Rev A04

Mellanox Technologies 9

Please send your documentation-related comments and feedback or report mistakes to docs@Mel-

lanox.com.

We are committed to improving our documentation and your feedback is important to us.

Rev A04

Mellanox Technologies

Intended Audience

This manual is for system administrators responsible for installing the Mellanox Vantage 8500

10GbE Layer-2 core switch, hereafter referred to as Vantage 8500. We assume you are familiar

with the concepts and terminology of Ethernet and local area networking.

Tabla de contenidos

Otros manuales de Cambiar de Mellanox Technologies

Mellanox Technologies

Mellanox Technologies InfiniScale MTS3600Q-1UNC Manual de usuario

Mellanox Technologies

Mellanox Technologies MIS5022Q-1BFR Manual de usuario

Mellanox Technologies

Mellanox Technologies SX6720 Instrucciones de uso

Mellanox Technologies

Mellanox Technologies MIS5024 Manual de usuario

Mellanox Technologies

Mellanox Technologies SX6518-NR Manual

Mellanox Technologies

Mellanox Technologies 1G Switch Air Duct Rail Kit Manual de usuario

Mellanox Technologies

Mellanox Technologies Spectrum SN2740 Instrucciones de uso

Mellanox Technologies

Mellanox Technologies Mellanox SX1018 Manual de instrucciones

Mellanox Technologies

Mellanox Technologies IS5025D-1BRC Manual de usuario

Mellanox Technologies

Mellanox Technologies MIS5300 Manual

Mellanox Technologies

Mellanox Technologies MIS5600Q-10DNC Manual de usuario

Mellanox Technologies

Mellanox Technologies MSX6512-4R Manual

Mellanox Technologies

Mellanox Technologies SX6710 Instrucciones de uso

Mellanox Technologies

Mellanox Technologies Mellanox SX1018 Manual de usuario

Mellanox Technologies

Mellanox Technologies Switch-IB Manual de usuario

Mellanox Technologies

Mellanox Technologies MIS5600Q-10DNC Manual de usuario

Mellanox Technologies

Mellanox Technologies MSX6536-10R Manual

Mellanox Technologies

Mellanox Technologies SwitchX-2 MSX1012B-1BFS Manual de usuario

Mellanox Technologies

Mellanox Technologies switchx MSX1035B-1BRR Manual de usuario

Mellanox Technologies

Mellanox Technologies MSX6536-10R Manual

Mellanox Technologies

Mellanox Technologies SwitchX-2 MSX6005F-1BFS Instrucciones de uso

Mellanox Technologies

Mellanox Technologies SwitchX-2 MSX6018F-1SFS Instrucciones de uso

Mellanox Technologies

Mellanox Technologies TX6100 MetroX Series Instrucciones de uso

Mellanox Technologies

Mellanox Technologies SX67X0 Instrucciones de uso

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario