Melitta Caffeo Solo Manual de usuario

EN Operating Instructions 14

BA_Solo_082016.indd 1 21.09.2016 07:23:50

B C

D E

BA_Solo_082016.indd 2 21.09.2016 07:23:50

Safety instructions

Please carefully read and

comply with the operating

instructions.

The appliance is intended for

home use only and not for

commercial purposes.

Any other use is regarded

as improper and may lead to

personal injury and material

damage. Melitta®accepts no

liability for damage which arises

due to improper use of the

appliance.

The appliance conforms to the

following European directives:

–2014 / 35 / EU (low voltage),

–2014 / 30 / EU (electromagnetic

compatibility),

–2011 / 65 / EU (RoHS),

–2009 / 125 / EC (eco-design / ErP).

The appliance has been built using the

latest technology. Residual dangers

nevertheless exist.

You must observe the safety

instructions to avoid dangers. Melitta®

accepts no liability for damage caused

by failure to observe the safety

instructions.

Warning!

Danger due to electrical current

If the appliance or the power cable

is damaged, the risk of a fatal

electric shock is run.

Observe the following safety

instructions to avoid dangers due

to electrical current:

–Do not use a damaged power

cable.

–A damaged power cable

may only be replaced by the

manufacturer, its customer

service or a similarly qualied

person.

–Do not open any covers rmly

screwed onto the appliance

housing.

–Only use the appliance when

it is in a technically awless

condition.

–A defective appliance may only

be repaired by an authorised

workshop. Do not repair the

appliance yourself.

–Do not undertake any changes

to the appliance, its components

or its accessories.

–Do not immerse the appliance in

water.

BA_Solo_082016.indd 14 21.09.2016 07:23:52

Warning!

Risk of burning and scalding

Escaping uids and steam may

be very hot. Parts of the appliance

also become very hot.

Observe the following safety

instructions to avoid scalds and

burns:

–Prevent skin from coming into

contact with escaping uids and

steam.

–Do not touch any nozzles on the

outlet during operation.

Warning!

General safety

Observe the following safety

instructions to avoid personal

injury and material damage:

–Do not reach into the interior of

the appliance during operation.

–The appliance and its power

cable must be kept out of the

reach of children under 8 years

of age.

–This appliance may be used

by children over 8 years of

age and by persons with

reduced physical, sensory or

mental capabilities or a lack

of experience and knowledge

if they are supervised or have

been instructed in using the

appliance safely and understand

the resulting risks.

–Children must not play with

the appliance. Cleaning and

maintenance must not be

undertaken by children younger

than 8 years of age. Children

over 8 years of age must be

supervised during cleaning and

maintenance.

–Disconnect the appliance from

the power supply when it is left

unsupervised for a long time.

BA_Solo_082016.indd 15 21.09.2016 07:23:52

At a glance

Figure A

Drip tray with cup plate and coffee

grounds container as well as display

for full drip tray

2 Height-adjustable outlet

3 Coffee quantity regulator

4Button for single-cup dispensing

5Button for two-cup dispensing

6 Water reservoir

7 Bean container

8Button for coffee strength

9 Display

10 ON/OFF button

Right cover (removable, covering the

grinding neness adjustment element,

brewing unit and identication label)

Display

Illuminated The appliance is ready

for operation.

Flashing

Appliance is heating

up or coffee is being

dispensed.

Illuminated Change the Melitta®

Claris® water lter

Flashing Filter change in process.

Illuminated Fill the water reservoir

Flashing Insert the water reservoir

Illuminated Empty drip tray and cof-

fee grounds container

Flashing Insert the drip tray and

coffee grounds container

Illuminated

1 bean: mild

2 beans: normal

3 beans: strong

Flashing

Fill bean container; as-

hing stops after dispen-

sing the next coffee.

Illuminated Clean the appliance

Flashing Integrated cleaning pro-

gramme is running.

Illuminated Descale the appliance

Flashing Integrated descaling

programme is running.

Illuminated

There is air in the system.

If necessary, ll the water

tank and press the button

for coffee strength .

The appliance is vented.

BA_Solo_082016.indd 16 21.09.2016 07:23:52

Before using for the rst time

General information

• Only use pure water without

carbonation.

• Use the supplied test strip to determine

the hardness of the water used and set

the water hardness ("Water hardness

and lter" page 18).

Information for using for the rst

time

The appliance must be vented before

it is used for the rst time. To do so,

the appliance may only be switched on

without a Melitta®Claris® water lter and

with a completely lled water reservoir.

• Place a vessel under outlet 2.

• Press the button to switch on the

appliance. illuminates on the display.

• Press the button. Water will be

pumped through the system.

• The appliance is ready for operation

when illuminates on display 9.

• After using the appliance for the rst

time, insert the Melitta®Claris®water

lter if required (see page 19).

Starting up the appliance

Starting up

Warning!

Danger of re and electric shock

due to incorrect supply voltage,

incorrect or damaged connections

and power cable.

–Ensure that the supply voltage

corresponds to the supply voltage

specied on the identication label of

the appliance. The identication label is

located on the right side of the appliance

behind the cover (Image A, 11).

–Make sure that the power socket meets

the applicable standards for electrical

safety. If in doubt, contact a qualied

electrician.

–Never use damaged power cables

(damaged insulation, bare wires).

• Place the appliance on a stable, dry and

level surface with sufcient clearance (at

least 10 cm) to the sides.

• Plug the power cable into a suitable

power socket.

• Remove the lid from the bean

container 7.

• Fill the bean container with suitable

coffee beans.

• Put the lid back on.

• Raise the lid of the water reservoir 6and

pull the water reservoir up and out of the

appliance.

• Fill the water reservoir with fresh tap

water only up to the max. mark.

BA_Solo_082016.indd 17 21.09.2016 07:23:52

• Insert the water reservoir into the

appliance.

• Place a vessel under outlet 2.

• Press the ON/OFF button to switch

the appliance on or off. The appliance

will perform an automatic rinse if

necessary.

Preparation

• Fill the water reservoir with fresh water

every day. The water reservoir must

always be lled with enough water for

the operation of the appliance.

• Fill the bean container preferably with

espresso beans or bean mixtures for

fully automatic coffee machines.

Do not use any ground, glazed,

caramelised or otherwise sugar-coated

coffee beans.

Setting the dispensed quantity and

strength

• Turn the coffee quantity regulator 3to

innitely adjust the dispensed quantity.

Regulator all the way to the left = 30 ml

per cup

Regulator all the way to the right =

220 ml per cup

• Press the button until the desired

strength is adjusted. The strength is

displayed by the beans on display 9

(from = mild to = strong).

Dispensing coffee or espresso

One or two cups can be dispensed

simultaneously.

• Switch on the appliance.

• Place one or two cups under the outlet.

• Preparing one cup: Press the button for

single-cup dispensing or

• Preparing two cups: Press the button for

two-cup dispensing.

• Press the corresponding button again to

cancel the coffee dispensing.

Water hardness and lter

It is important to properly set the water

hardness so that the appliance displays

the need to be descaled in due time. From

the factory, it is set at water hardness 4.

After inserting a Melitta®Claris®water

lter, it is automatically set at hardness

level 1.

Melitta®Claris® water lter

The Melitta®Claris® water lter removes

lime and other harmful substances from

the water. The water lter should be

changed every 2 months, however, at the

latest when appears on the display.

The water lter is available in specialised

shops.

BA_Solo_082016.indd 18 21.09.2016 07:23:53

Inserting the water lter

ashes during the entire changing

process.

• Put the water lter in a glass with

tap water for several minutes before

inserting it in the appliance.

• Switch off the appliance.

• Press and hold the and buttons

for ca. 3 seconds, then release.

appears on the display.

• Empty and insert the drip tray.

illuminates.

• Pull the water reservoir 6up and out of

the appliance.

• Empty the water reservoir.

• Screw the water lter onto the thread at

the bottom of the water reservoir.

• Fill the water reservoir with fresh tap

water up to the max. mark.

• Insert the water reservoir into the

appliance.

• Press the button. The appliance

performs an automatic rinse. When

rinsing is nished, the appliance is ready

for operation and the water hardness is

set to hardness level 1.

• Empty and insert the drip tray.

After inserting the water lter, the water

can be cloudy during the rst rinse

because excess activated carbon is

washed out of the lter. The water then

becomes clear again.

Setting the water hardness

The appliance includes a test strip to

determine the water hardness.

• Determine the hardness of the tap water

using the test strip.

• Switch on the appliance.

• Press the and button

simultaneously for longer than 2

seconds. ashes rapidly.

• Press the button to show the menu

for setting the water hardness.

illuminates.

• Set the determined water hardness by

pressing the button. The selected

water hardness is shown by the bean

symbols .

Water hardness °dH °e °fH

1: 0 - 10 0 - 13 0 - 18

2: 10 - 15 13 - 19 18-27

3: 15 - 20 19 - 25 27-36

4: ashing >20 >25 >36

• Press to conrm the selection.

BA_Solo_082016.indd 19 21.09.2016 07:23:53

Care and cleaning

Warning!

–Pull the power supply plug before

cleaning.

–Never immerse the appliance in

water.

–Do not use a steam cleaner.

Daily cleaning

• Wipe the outside of the appliance with a

soft damp cloth and normal dishwashing

liquid.

• Empty the drip tray.

• Empty the coffee grounds container.

Cleaning the brewing unit

It is recommended to clean the brewing

unit once a week.

• Switch off the appliance.

• Pull off the cover 11 to the right.

• Press and hold the red button on the

handle of the brewing unit (Image B, 1).

• Turn the handle clockwise until the stop.

• Pull the brewing unit out of the appliance

by the handle.

• Rinse the brewing unit thoroughly on all

sides with clear water. The area shown

in Image D(arrow) must be free of

coffee residues.

• Let the brewing unit drip dry.

• Remove coffee residues from the

appliance.

• Insert the brewing unit back into the

appliance, press and hold the red

button (Image B, 1) and turn the handle

counterclockwise until the stop.

• Insert the cover until it clicks in.

Integrated cleaning programme

The integrated cleaning programme (takes

about 15 minutes) removes residues and

coffee oil residues that cannot be removed

by hand. The cleaning symbol ashes

during the entire process.

The cleaning programme should be

performed every 2 months or after 200

brewed cups, however, at the latest when

is lit up.

Only use Melitta®cleaning tabs.

• Switch off the appliance.

• Fill the water reservoir with tap water up

to the max. mark.

• Insert the water reservoir.

• Press the and buttons

simultaneously for approx. 3 seconds.

ashes, illuminates.

• Empty the drip tray and coffee grounds

container.

• Insert the drip tray without the coffee

grounds container

• Place the coffee grounds container

under outlet 2.

Cleaning phase 1 ( ):

Two rinse cycles are performed. When

illuminates, proceed as follows:

• Remove and clean the brewing unit

("Cleaning the brewing unit", page

20).

• Put a cleaning tab in the brewing unit

(Image C).

• Insert the brewing unit ("Cleaning the

brewing unit" page 20).

BA_Solo_082016.indd 20 21.09.2016 07:23:53

Cleaning phase 2 ( ):

When illuminates, proceed as follows:

• Fill the water reservoir with tap water up

to the max. mark.

• Press outlet 2all the way down.

• Press the button to continue with

the cleaning programme (takes about 5

minutes).

Cleaning phase 3 ( ):

When illuminates, proceed as follows:

• Empty the drip tray and coffee grounds

container.

• Insert the drip tray without the coffee

grounds container

• Place the coffee grounds container

under outlet 2.

Cleaning phase 4 ( , the middle

bean is ashing):

• The cleaning programme will be

continued again and takes about 5

minutes.

When illuminates, proceed as follows:

• Empty the drip tray and coffee grounds

container and insert them in the

appliance as usual.

The cleaning programme is nished.

Integrated descaling programme

Warning!

The descaling agent can cause skin

irritations

Comply with the safety instructions

and the dosing information specied

on the descaling agent packaging.

The integrated descaling programme

(takes about 30 minutes) removes lime

residues inside the appliance. The symbol

for descaling ashes during the entire

process.

The descaling programme should be

performed every 3 months, however, at

the latest when illuminates ("Setting

the water hardness" page 19).

Only use Melitta®ANTI CALC.

• Switch off the appliance.

• Remove the water lter if necessary

("Water hardness and lter", page 18).

• Press the and buttons

simultaneously for approx. 3 seconds.

ashes, illuminates.

Descaling phase 1 ( ):

• Empty and insert the drip tray.

illuminates.

• Completely empty the water reservoir.

• Add the descaling agent to the water

reservoir according to the instructions on

the packaging.

• Insert the water reservoir.

• Press the button to start the

descaling programme (takes about 15

minutes).

BA_Solo_082016.indd 21 21.09.2016 07:23:53

Otros manuales para Caffeo Solo

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cafetera de Melitta

Melitta

Melitta Choco Latte MECM1 Manual de usuario

Melitta

Melitta Excellent 5.0 Manual de usuario

Melitta

Melitta ME5CB Manual de usuario

Melitta

Melitta Senz V MSP001 Manual de usuario

Melitta

Melitta LOOK Therm Selection Manual de usuario

Melitta

Melitta Avanza 600 Series Manual de usuario

Melitta

Melitta MEPE123B Manual de usuario

Melitta

Melitta Caffeo Bistro Manual de usuario

Melitta

Melitta Caffeo Solo & Perfect Milk Manual de usuario

Melitta

Melitta One:One MES2B Manual de usuario

Melitta

Melitta amano Manual de usuario

Melitta

Melitta SINGLE 5 THERM Manual de usuario

Melitta

Melitta Optima Therm Manual de usuario

Melitta

Melitta Look Aromagic Manual de usuario

Melitta

Melitta ME2TMDS Manual de usuario

Melitta

Melitta Caffeo Solo Manual de usuario

Melitta

Melitta solo & milk Manual de usuario

Melitta

Melitta LOOK Therm Selection DeLuxe Manual de usuario

Melitta

Melitta AROMA SIGNATURE Manual de usuario

Melitta

Melitta LOOK Manual de usuario

Melitta

Melitta Caffeo Solo & Milk Manual de usuario

Melitta

Melitta CI E970-103 Manual de usuario

Melitta

Melitta Optima Timer 818467 Manual de usuario

Melitta

Melitta Choco Latte MECM1 Manual de usuario

Manuales populares de Cafetera de otras marcas

Taurus

Taurus Livorno 6 Manual de usuario

Delta-q

Delta-q QUICK Manual de usuario

Bunn

Bunn LCA-1 Guía de solución de problemas

Black & Decker

Black & Decker BLACK DECKER HOME DE790 Instrucciones de instalación

Saeco

Saeco Vienna Plus Sup 018M Manual de usuario

DeLonghi

DeLonghi DC300 Manual de usuario

INCAPTO

INCAPTO BXCO1470E Manual de usuario

Bosch

Bosch TASSIMO finesse TAS16B Series Manual de usuario

Exido

Exido 245-072 Manual de usuario

Animo

Animo OptiVend Choco Manual de usuario

Siemens

Siemens TQ505DF Series Manual de usuario

DeLonghi

DeLonghi ECI341 Manual de usuario

Krups

Krups KT406511 Manual de usuario

Cimbali

Cimbali M32 Classic Manual de usuario

Philips

Philips HL3844N Manual de usuario

Bosch

Bosch TES 515 SERIES Manual de usuario

Tekmatix

Tekmatix TMFM - 65 Manual de usuario

Scarlett

Scarlett SC-CM33005 Manual de usuario