Meilhaus Electronic ME-94 PCI Manual de usuario

Meilhaus Electronic Manual

ME-94, ME-95, ME-96 6.0E

(PCI- and CompactPCI-Versions)

Opto-Isolated Digital-I/O Boards

Imprint

Manual ME-94, ME-95, ME96

Revision 6.0

Revised: 2018-06-07

Meilhaus Electronic GmbH

Am Sonnenlicht 2

D-82239 Alling bei München

Germany

www.meilhaus.de

or distributed in any form whether photocopied, printed, put on

microfilm or be stored in any electronic media without the

expressed written consent of Meilhaus Electronic GmbH.

Important note:

The information contained in this manual has been reviewed with

great care and is believed to be complete and accurate. Meilhaus

Electronic assumes no responsibility for its use, any infringements

of patents or other rights of third parties which may result from

use of this manual or the product. Meilhaus Electronic assumes no

responsibility for any problems or damage which may result from

errors or omissions. Specifications and instructions are subject to

change without notice.

Note the Meilhaus Electronic general terms of business:

www.meilhaus.de/en/infos/my-shop/tob/

All trademarks acknowledged. All trademarks are property of their

respective owners.

Content

1Introduction...........................................................4

1.1 Important Notes ............................................................... 4

1.1.1 Use in Accordance with the Requirements ....................... 4

1.1.2 Improper Application ...................................................... 5

1.1.3 Unforeseeable Misapplications ........................................ 5

1.2 Package Contents ............................................................. 6

1.3 Features .......................................................................... 6

1.4 System Requirements ....................................................... 7

1.5 Software Support ............................................................. 7

2Starting up............................................................8

2.1 Software Installation ......................................................... 8

2.2 Test Program.................................................................... 8

3Hardware ..............................................................9

3.1 Block Diagrams ................................................................. 9

3.2 Digital I/O ....................................................................... 10

3.2.1 External Power Supply.................................................. 10

3.2.2 Opto-Isolated Inputs .................................................... 10

3.2.3 Opto-Isolated Outputs ................................................. 11

4Programming .......................................................12

5Appendix .............................................................14

ASpecification .......................................................................... 14

BPinout ................................................................................... 16

B1 ME-94........................................................................... 16

B2 ME-95........................................................................... 17

B3 ME-96........................................................................... 18

B4 External Power Connector............................................... 19

CAccessories........................................................................... 20

DTechnical Questions ................................................................ 21

D1 Hotline ........................................................................... 21

EIndex ..................................................................................... 22

1 Introduction

Valued customer,

Thank you for purchasing this device from Meilhaus Electronic. You

have chosen an innovative high technology product that left our

premises in a fully functional and new condition.

Please take the time to carefully examine the contents of the

package for any loss or damage that may have occurred during

shipping. If there are any items missing or if an item is damaged,

please contact us immediately.

Before installing the board in your computer, we recommend you

read this manual carefully, especially the chapter describing board

installation.

The descriptions in this manual concern PCI- and CompactPCI-

versions of the ME-94, ME-95, ME-96 series, if not otherwise

noted.

1.1 Important Notes

1.1.1 Use in Accordance with the Requirements

The PC-boards of the ME-series are designed for acquisition and

output of analog and digital signals with a PC. Depending on type

install the models of the ME-series into:

a free PCI-slot (PCIe versions) or

a free CompactPCI-slot (3 HE cPCI versions).

For information on how to install a plug-in board or connect a USB

device, please read the manual of your PC.

Please note the instructions and specifications as presented in

this manual (Appendix A, Specifications):

Please ensure sufficient heat dissipation for the board within

the PC housing.

All unused inputs should be connected to the ground reference

of the appropriate functional section. This avoids cross talk

between the input lines.

The opto-isolated inputs and outputs achieve an electrical

isolation of the application relative to PC ground.

Note that the computer must be powered up prior to

connecting signals by the external wiring of the board.

As a basic principle, all connections to the board should only be

made or removed in a powered-down state of all components.

Ensure that no static discharge occurs while handling the

board or while connecting/disconnecting the external cable.

Ensure that the connection cable is properly connected. It

must be seated firmly on the D-Sub connector and must be

tightened with both screws, otherwise proper operation of the

board cannot be guaranteed.

1.1.2 Improper Application

PC plug-in boards for the PCI- or CompactPCI-bus may not be taken

into operation outside of the PC. Never connect the devices with

voltage-carrying parts, especially not with mains voltage.

Make sure that no contact with voltage-carrying parts can happen

by the external wiring of the device. As a basic principle, all

connections should only be made or removed in a powered-down

state.

1.1.3 Unforeseeable Misapplications

The device is not suitable to be used as a children’s toy, in the

household or under unfavourable environmental conditions (e.g. in

the open). Appropriate precautions to avoid any unforeseeable

misapplication must be taken by the user.

1.2 Package Contents

We take great care to ensure your delivery is complete.

Nonetheless, please check the list enclosed to verify the contents

of your delivery. You should find included:

Opto-isolated digital-I/O board (depending on the package of the

PCI or cPCI board of ME-94, ME-95 or ME-96)

Manual in PDF format on CD-ROM

Driver software on CD-ROM

For the PCI versions only: DIN-connector sourcing the

optocoupler’s power

ME-94 and ME-95: one DB25 female connector

ME-96: two DB15 female connectors

1.3 Features

Model Overview

Model

IRQ

Inputs

Outputs

ME-94 PCI

ME-94 cPCI

16 opto-isolated** (24 V)

ME-95 PCI

ME-95 cPCI

16 opto-isolated (24 V)

ME-96 PCI

ME-96 cPCI

8 opto-isolated** (24 V)

8 opto-isolated (24 V)

* The interrupt function is not supported by the ME-iDS.

** Input port PC is not supported by ME-iDS.

The ME-9x board family includes opto-isolated digital-I/O boards for

the PCI- and cPCI-bus. The same boards on different buses are

functionally equivalent, pin-compatible, and software-compatible.

The electrical isolation on the boards prevents interference and

high voltages (e.g. voltage peaks on the ground lines) from reaching

the PC electronics. The inputs have been designed for a voltage of

typical 24 V used in control engineering.

Using the ME-iDS you can program the ME-9x series for simple in-

put/output operations.

ME-94: 2 x 8-bit input ports.

ME-95: 2 x 8-bit output ports.

ME-96: 1 x 8-bit input ports, 1 x 8-bit output port.

1.4 System Requirements

The ME-series may be installed into any PC (Intel® Pentium®

processor) with a free standard PCI- and CompactPCI-slot (32 bit,

33 MHz, 5 V). The board is supported by the Meilhaus Electronic

Intelligent Driver System (ME-iDS).

1.5 Software Support

The ME-series is supported by the Meilhaus Electronic Intelligent

Driver System (ME-iDS). The ME-iDS is a unique driver system

covering different devices and operating systems. It supports

Windows XP/Vista and Windows 7, 8.1, 10 and contains a universal

function library (API) for all common programming languages.

A detailed description of the functions can be found in the ME-iDS

manual on the CD/DVD enclosed.

Please also note the corresponding README-files.

2 Starting up

Please read your computer’s instruction manual on how to install

new hardware components before installing the board.

2.1 Software Installation

Installation under Windows

The following basic procedure should be used:

If you have received the driver software as an archive file, please

unpack the software before installing the board. First choose a

directory on your computer (e.g. C:\Temp\Meilhaus\ME-iDS).

Use the Meilhaus Electronic Intelligent Driver System (ME-iDS) for

programming your new data acquisition hardware. For installation

and operation of the driver system, please follow the

documentation in electronic form included with the software

package.

2.2 Test Program

For simple testing of the board use the corresponding test

program provided with the ME-iDS.

3 Hardware

3.1 Block Diagrams

3.2 Digital I/O

The inputs and outputs of the ME-9x series are electrically isolated

by optocouplers. There is no electrical connection between the

hardware connected to the board and the PC.

The inputs and outputs are designed for 24 V level used in control

engineering.

For programming please read chapter 4.0 "Digital-I/O Section" on

page 12. For pin out diagrams of the connectors, see page 16.

3.2.1 External Power Supply

In order to run the ME-9x boards properly, an external power

supply is required for the optocouplers. The power supply must be

connected to the D-Sub connector of the boards (pins „ext. GND“

and „ext. V+“, see chapter "B Pinout" on page 16 ff). Alternatively,

the external power can be supplied via a low-voltage connector (DIN

45323) on the standard PCI versions. The power supply is

connected to the „V+“ pins at the D-Sub connector(s) on the

board.

The external supply voltage can be within 20 V and 28 V, so that

small alterations in the voltage will have no effect on the board’s

function.

3.2.2 Opto-Isolated Inputs

The opto-isolated inputs of the ME-94 and ME-96 are connected

to the optocouplers through resistors Rv. These resistors are sized

for an input high level of typical 24 V. For over-voltage protection of

the optocouplers a protection diode is provided. The digital lines

must be referenced to the external ground (ext. GND).

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de E/S de Meilhaus Electronic

Meilhaus Electronic

Meilhaus Electronic ME-5004 Manual de usuario

Meilhaus Electronic

Meilhaus Electronic ME-5001 Manual de usuario

Meilhaus Electronic

Meilhaus Electronic ME-1400 Manual de usuario

Meilhaus Electronic

Meilhaus Electronic ME-8100 Series Manual de usuario

Meilhaus Electronic

Meilhaus Electronic ME-1000 Series Manual de usuario

Meilhaus Electronic

Meilhaus Electronic RedLab 1024HLS Manual de usuario

Meilhaus Electronic

Meilhaus Electronic ME-5810 Series Manual de usuario

Meilhaus Electronic

Meilhaus Electronic RedLab TC Manual de usuario

Meilhaus Electronic

Meilhaus Electronic ME-5310 Series Manual de usuario

Meilhaus Electronic

Meilhaus Electronic ME-5100 Series Manual de usuario

Meilhaus Electronic

Meilhaus Electronic ME-630 Series Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

M-system

M-system R3Y-RS8 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario