Megger AVO210 Manual de usuario

AVO210

Digital multimeter

User manual

99 Washington Street

Melrose, MA 02176

Phone 781-665-1400

Toll Free 1-800-517-8431

Visit us at www.TestEquipmentDepot.com

G SAFETY INFORMATION

Understand and follow operating instructions carefully.

GWARNING

■Do not use test leads or the multimeter if they are damaged

■Do not use the multimeter if the tester is not operating properly

■To reduce risk of ﬁre and shock do not expose this product to rain or

any moisture

■When using test leads or probes, keep ﬁngers behind the ﬁnger guards.

■Remove test leads from meter before opening the battery door or meter

case.

■Use the meter only as speciﬁed in this manual or the protection by the

meter might be impaired.

■Always use proper terminals, switch position, and range for measurements.

■Never attempt a voltage measurement with the test lead inserted into the

A input terminal.

■Verify the meter’s operation by measuring a known voltage. If in doubt,

have the meter serviced.

■Do not apply more than the rated voltage, as marked on meter, between

terminals or between any terminal and earth ground.

■Do not attempt a current measurement when the open voltage is above the

fuse protection rating.

■Suspected open circuit voltage can be checked with voltage function.

■Only replace the blown fuse with the proper rating as speciﬁed in this

manual.

■Use caution with voltages above 30 Vac rms, 42 Vac peak , or 60 Vdc.

These voltages pose a shock hazard.

■To avoid false readings that can lead to electric shock and injury, replace

battery as soon as low battery indicator appears.

■Disconnect circuit power and discharge all high voltage capacitors before

testing resistance, continuity, diodes, or capacitance.

■Do not use meter around explosive gas or vapour.

GCAUTION

■Disconnect the test leads from the test points before changing the position

of the function rotary switch.

■Never connect a source of voltage with the function rotary switch

W, , d,a,A, bposition.

■Do not expose Meter to extremes in temperature or high humidity.

■Never set the meter in daA function to measure the voltage of a

power supply circuit in equipment that could result in damage the meter

and the equipment under test.

Symbols as marked on the meter and instruction card

FRisk of electric shock

GSee instruction card

dDC measurement

tEquipment protected by double or reinforced insulation

Battery

aAC measurement

cConforms to EU directives

Maintenance

Do not attempt to repair this Meter. It contains no user-serviceable parts. Repair or

servicing should only be performed by qualiﬁed personnel.

Cleaning

Periodically wipe the case with a dry cloth and detergent. Do not use abrasives or

solvents.

AC / DC Voltage and Frequency

Continuity and Diode

Resistance and Capacitance

Note – To improve the measurement accuracy of small value capacitor, record the

reading with the test leads open, then subtract the residual capacitance of the meter

and leads from measurement.

CUNKNOWN = CMEASUREMENT - CRESIDUAL

MIN MAX Record

DC / AC Current

Display Hold

Manual Ranging and Auto Ranging

Auto Power Off (Battery Saver)

Disable Auto Power Off

Test Equipment Depot - 800.517.8431

99 Washington Street Melrose, MA 02176

TestEquipmentDepot.com

Non-Contact Voltage Alert (VOLTSENSE)

1. Volt sense switch will be activated on any function or at OFF status.

2. Test leads are not used for the Volt sense test.

3. Press the Volt sense button. The display will blank out, a tone sounds

and the red LED lights up to verify the instrument is operational. The

Volt sense button must be held down to detect the presence of voltage

without use of the leads.

4. If a voltage of 50V to 600V (50 to 500Hz) is detected near the top of

meter a continuous tone sounds and the red LED near the top of meter

illuminates.

Fuse Replacement

Refer to the following diagram to replace fuse.

GUse only a fuse with the amperage, interrupt, voltage,

and speed rating speciﬁed.

˙ Fuse rating: 10A, 500V

Tabla de contenidos

Otros manuales de Instrumento de medición de Megger

Megger

Megger BD-59095 Manual de usuario

Megger

Megger MOM690 Manual de usuario

Megger

Megger 1006-603 Manual de usuario

Megger

Megger DCM305E Manual de usuario

Megger

Megger MTO106 Manual de usuario

Megger

Megger TDR2000/3 Manual de usuario

Megger

Megger MPQ1000 Manual de usuario

Megger

Megger DLRO10HD Manual de usuario

Megger

Megger LT7 Manual de usuario

Megger

Megger HV DAC-300 Manual de usuario

Megger

Megger DLRO100EB Manual de usuario

Megger

Megger PDS 62-SIN Manual de usuario

Megger

Megger HV DAC-200 Manual de usuario

Megger

Megger TDR2050 Manual de usuario

Megger

Megger MOM2 Manual de usuario

Megger

Megger DLRO100E Manual de usuario

Megger

Megger TTRU3 Manual de usuario

Megger

Megger TDR2000/3 Manual de usuario

Megger

Megger EGIL200 Series Manual de usuario

Megger

Megger MOM200A Manual de usuario

Megger

Megger Surgeflex 8-1000 Manual de usuario

Megger

Megger Digiflex Com Manual de usuario

Megger

Megger DET14C Manual de usuario

Megger

Megger 210600 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario