MECHA F9988 Manual de usuario

IR REMOTE

COMMANDER & RECEIVER

November 24, 2022

MECHA IR Remote Commander and Receiver v.1.2.2 
 
 © 2021-2022 FANOTEC 2 
 
Contents
 
Introduction ................................................................................4 
Before First Use ..........................................................................5 
Functions .....................................................................................7 
Power Button..........................................................................................................7 
Menu Button...........................................................................................................8 
Directional Buttons ................................................................................................8 
Trigger Button ........................................................................................................9 
Pause Button ..........................................................................................................9 
Numerical Buttons.................................................................................................9 
Specifications ............................................................................11 
Testing the IR Remote Commander & Receiver....................11 
Troubleshooting.................................................................................... 14 
Appendix....................................................................................15 
Particular Use............................................................................15 
Shutter Release Confirmation and IR Remote Control.................... 15 
Use Two IR Receivers (DAC ONLY)...................................................... 17 
What is New...............................................................................18 
Useful Links ...............................................................................19 
 
 

MECHA IR Remote Commander and Receiver v.1.2.2

MECHA IR Remote Commander & Receiver

NDownload the latest version of this guide from

https://www.nodalninja.com/Manuals/mecha-ir-remote.pdf

Web: www.nodalninja.com, www.fanotec.com

Support email address: [email protected]

any form by any means, electronic, mechanical, photocopying, recording, or

otherwise, without the prior written permission of the publisher. For

information on getting permission for reprints and excerpts, contact

[email protected]

MECHA IR Remote Commander and Receiver v.1.2.2

Introduction

IR Remote Commander and Receiver

for MECHA is a kit specially designed

by Fanotec to work with MECHA C1

and C2 Controllers. It allows basic

controls and execution of program

presets wirelessly without touching

the camera, controller or any smart

device.

Although both controllers have

their own buttons, they cannot

be used when mounted on a

high pole, such as Fanotec

Carbon Fiber Pole Series 3 –

9.25m extended, or even on the

Travel Pole –2.9m extended.

In this case, remote control is

very helpful and the only

solution at the same time.

However, occasionally you may

not want to touch the controller

for some reason, or it may be

much more comfortable to use

the remote control than the

controller or a smart device.

Use it with MECHA to rotate a

turntable, and your life will be

much easier.

MECHA C1 Controller

Commander

(Transmitter)

MECHA C2 Controller

MECHA IR Remote Commander and Receiver v.1.2.2

Before First Use

•First, remove the battery cover on the back of the Commander and insert

two AAA batteries paying attention to polarity.

•To be able to use the IR Remote Commander and Receiver for MECHA,

connect the Receiver to the AUX Port of the C1 or C2 Controller used.

MECHA C1 Controller

MECHA C2 Controller

Receiver

MECHA IR Remote Commander and Receiver v.1.2.2

Vhttps://youtu.be/ufIbFlvhHT4

Using a Smartphone to Access the MECHA User Interface for Dual Axis and

Single Axis Controllers

•Access the Configuration (/config) page of MECHA at:

192.168.8.1/config

User:

admin

Password:

Mecha

Next check the following checkbox –required: Use Nodal Ninja IR Remote.

Then click the [Apply] button to save the new settings.

•Alternatively, the use of the remote control can be enabled/disabled:

owith the code: 3232<, when using a C1 Controller;

owith the USE NN IR option in the Config Menu, when using a C2

Controller.

oCheck the following checkbox on the Configuration page if you prefer to

press the Commander power button twice to power off MECHA: Double

press the Nodal Ninja IR Remote power button for power OFF.

MECHA IR Remote Commander and Receiver v.1.2.2

Vhttps://youtu.be/94oIpK7xwJQ

Using IR Remote Commander and Receiver to Launch Presets –MECHA DAC

and Single Axis

Functions

The functions of the Commander buttons are similar to the functions of the C1

and C2 Controller buttons. Some functions are listed below.

Power Button

•0The power button has many functions and can be used as follows:

oTo power off MECHA:

▪Long press is required, unless otherwise set on the Configuration

page.

▪Press the power button twice if the Double press the Nodal Ninja IR

Remote Power button for power OFF checkbox is checked on the

Configuration page.

To power on MECHA, use the 0button on the C1 or C2 Controller used.

oTo confirm or cancel some operations, for example:

▪If you enter a code and notice on C2’s display, or on C1’s LEDs, that

the code is wrong, before confirming or specifying the direction, you

can cancel the code with the power button and enter the code again.

oUse the power button to exit the C2’s Menu Mode (in Advanced Mode).

MECHA IR Remote Commander and Receiver v.1.2.2

oUse the power button to check the battery level when MECHA is idle.

oIt is also the equivalent of the number 0 (zero) when power codes are

entered.

Power codes are codes that start with zero. They can be used as shortcuts

for launching a preset. For example, you can easily launch a preset named

01 PresetName using the 01 button combination.

!Please note that the power button, 0, can always be used as an

emergency stop, if necessary, except for the speed calibration procedure (code:

123123<).

Menu Button

•8Use this button to show or switch between the C2 Controller menus and

to show information about parameters in edit mode.

Directional Buttons

•45 Use the left and right arrow buttons to navigate in C2’s OLED menus,

or manually rotate the system to the left and to the right, respectively, and

also to specify the direction when launching a preset using the Commander

buttons, as terminator for codes (similar to the Enter key).

•67 The up and down arrow buttons can be used to navigate in C2’s OLED

menus and to control the up and down movement of the upper rotator,

when two rotators are used.

MECHA IR Remote Commander and Receiver v.1.2.2

Trigger Button

•SThe button located between the arrow buttons has camera trigger and

confirmation functions. During a Pause, by pressing Son Commander, or

by clicking [SHOOT] on the User Interface, MECHA will trigger the number of

shots specified by [TRG] in presets. This can be used for extra shots for a

particular position.

Pause Button

•:Pause button is the equivalent of [Pause] UI button.

•If MECHA is paused during the execution of a preset, it will pause before

every position, resulting in a step-by-step movement.

oYou can press 5on the C1/C2 Controller, or :on Commander, or

[PAUSE/NEXT] on the User Interface to continue to the next position.

oIf, instead, 4is pressed on the C1/C2 Controller, or Commander,

MECHA will continue to the next position and switch on/off the step-by-

step mode.

Numerical Buttons

•1Use it to enter the number 1. Use [Save 1] button in UI to save a preset

and assign it to this button.

oPress 14 to execute the Button 1 preset to the left.

oPress 15 to execute the Button 1 preset to the right.

MECHA IR Remote Commander and Receiver v.1.2.2

oAny directional button in combination with the 1button can be used to

perform simple (by default) 45° rotations.

•2Use it to enter the number 2. Use [Save 2] button in UI to save a preset

and assign it to this button.

oPress 24 to execute the Button 2 preset to the left.

oPress 25 to execute the Button 2 preset to the right.

oAny directional button in combination with the 2button can be used to

perform simple (by default) 90° rotations.

•3Use it to enter the number 3. Use [Save 3] button in UI to save a preset

and assign it to this button.

oPress 34 to execute the Button 3 preset to the left.

oPress 35 to execute the Button 3 preset to the right.

oAny directional button in combination with the 3button can be used to

perform simple (by default) 180° rotations.

•+9 The plus and minus buttons can be used in C2's edit mode to adjust

some settings, although the controller buttons are more suitable for this

purpose.

Tabla de contenidos

Manuales populares de Receptor de otras marcas

Garmin

Garmin GA 23 Manual de usuario

Aiphone

Aiphone PS-12F Manual de usuario

IMES

IMES TCS-01CA-PMI Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR Manual

AMIMON

AMIMON AMN12310 WHDI Manual de usuario

Dual

Dual DMCPA79BT Instrucciones de funcionamiento

Sound Associates

Sound Associates SA652P Manual de usuario

Sherwood

Sherwood NewCastle R-772 Manual de usuario

Audio

Audio A10-RX Series Manual de usuario

AllSee

AllSee PushShare PSRV1.1 Manual de usuario

DEMAG

DEMAG DRC-DR D2 Manual de usuario

Teleco

Teleco TVRCL868A02 Manual de usuario

Bosch

Bosch RF3222E Manual de usuario

Kramer

Kramer 631R Manual de usuario

Xpress

Xpress xmc10 Manual de usuario

JVC

JVC KD-MR1BTS Manual de usuario

Omega Engineering

Omega Engineering UWTC-REC3 Manual de usuario

e-survey

e-survey E300 Pro Manual de usuario