Measurement Computing PCIM-DDA06/16 Manual de usuario

PCIM-DDA06/16

Analog Output and Digital I/O

User's Guide

January 2019. Rev 9

HM PCIM-DDA06-16.docx

Trademark and Copyright Information

Measurement Computing Corporation, InstaCal, Universal Library, and the Measurement Computing logo are

either trademarks or registered trademarks of Measurement Computing Corporation. Refer to the Copyrights &

Trademarks section on mccdaq.com/legal for more information about Measurement Computing trademarks.

Other product and company names mentioned herein are trademarks or trade names of their respective

companies.

reproduced, stored in a retrieval system, or transmitted, in any form by any means, electronic, mechanical, by

photocopying, recording, or otherwise without the prior written permission of Measurement Computing

Corporation.

Notice

Measurement Computing Corporation does not authorize any Measurement Computing Corporation product for

use in life support systems and/or devices without prior written consent from Measurement Computing

Corporation. Life support devices/systems are devices or systems that, a) are intended for surgical implantation

into the body, or b) support or sustain life and whose failure to perform can be reasonably expected to result in

injury. Measurement Computing Corporation products are not designed with the components required, and are

not subject to the testing required to ensure a level of reliability suitable for the treatment and diagnosis of

people.

Table of Contents

Preface

About this User's Guide .......................................................................................................................4

What you will learn from this user's guide .........................................................................................................4

Conventions in this user's guide .........................................................................................................................4

Where to find more information.........................................................................................................................4

Chapter 1

Introducing the PCIM-DDA06/16..........................................................................................................5

Functional block diagram...................................................................................................................................5

Chapter 2

Installing the PCIM-DDA06/16..............................................................................................................6

Unpacking...........................................................................................................................................................6

Installing the software ........................................................................................................................................6

Configuring the hardware...................................................................................................................................6

Simultaneous transfer jumper ........................................................................................................................................... 6

Analog output range switch .............................................................................................................................................. 7

Installing the hardware .......................................................................................................................................7

Signal connections..............................................................................................................................................8

Cabling.............................................................................................................................................................................. 9

Field wiring, signal termination, and conditioning ........................................................................................................... 9

Chapter 3

Specifications......................................................................................................................................10

Analog output ...................................................................................................................................................10

Accuracy..........................................................................................................................................................................10

Analog output drift...........................................................................................................................................................11

Digital I/O.........................................................................................................................................................11

Power consumption ..........................................................................................................................................11

Environmental ..................................................................................................................................................11

Mechanical .......................................................................................................................................................11

Signal connector...............................................................................................................................................12

EU Declaration of Conformity............................................................................................................13

Preface

About this User's Guide

What you will learn from this user's guide

This user's guide describes the Measurement Computing PCIM-DDA06/16 data acquisition device and lists

device specifications.

Conventions in this user's guide

For more information

Text presented in a box signifies additional information and helpful hints related to the subject matter you are

reading.

Caution! Shaded caution statements present information to help you avoid injuring yourself and others,

damaging your hardware, or losing your data.

bold text Bold text is used for the names of objects on the screen, such as buttons, text boxes, and check boxes.

italic text Italic text is used for the names of manuals and help topic titles, and to emphasize a word or phrase.

Where to find more information

Additional information about PCIM-DDA06/16 hardware is available on our website at www.mccdaq.com.

You can also contact Measurement Computing Corporation with specific questions.

Knowledgebase: kb.mccdaq.com

Tech support form: www.mccdaq.com/support/support_form.aspx

Email: techsupport@mccdaq.com

Phone: 508-946-5100 and follow the instructions for reaching Tech Support

For international customers, contact your local distributor. Refer to the International Distributors section on our

web site at www.mccdaq.com/International.

If you need to program at the register level in your application, refer to the Register Map for the PCIM-

DDA06/16 on our website at www.mccdaq.com/registermaps/RegMapPCIM-DDA06-16.pdf.

Chapter 1

Introducing the PCIM-DDA06/16

The PCIM-DDA06/16 has six channels of analog output and 24 bits of digital input/output. Analog outputs are

from AD660 DACs, with each output buffered by an OP27. Digital I/O is performed with an 82C55.

Analog output ranges are either Bipolar or Unipolar. Bipolar ranges are ±10 V and ±5 V. Unipolar ranges are 0

to 10 V and 0 to 5 V. You set the analog output range for each DAC with an onboard switch. You set the analog

outputs for simultaneous or individual transfer with an on-board jumper.

The PCIM-DDA06/16 digital I/O lines are a direct interface to an 82C55. The 82C55 is a CMOS chip with TTL

level inputs and outputs. The 8255 can source or sink about 2.5 mA. This is enough to switch other TTL or

similar inputs, but is inadequate to drive relays, LEDs or solid-state relays without additional buffering.

The 82C55 digital I/O chip initializes all ports as inputs on power-up and reset.

The PCIM-DDA06/16 digital I/O is controlled by programming the 8255's mode register. There are three

possible modes. The most commonly used mode is Mode 0, simple input and output.

Functional block diagram

The PCIM-DDA06/16 board consists of two functional sections: analog output and digital I/O. The digital I/O

section consists of a single 82C55, and a 24-line digital I/O chip. The analog output section consists of six

identical circuits, each consisting of a DAC, an OP27 output buffer, and a gain range control switch. You can

control each analog output individually or control all six outputs simultaneously.

PCIM-DDA06/16 functions are illustrated in the block diagram shown here.

Figure 1. Functional block diagram

Chapter 2

Installing the PCIM-DDA06/16

Unpacking

As with any electronic device, you should take care while handling to avoid damage from static

electricity. Before removing the device from its packaging, ground yourself using a wrist strap or by simply

touching the computer chassis or other grounded object to eliminate any stored static charge.

Installing the software

Refer to the MCC DAQ Quick Start and the PCIM-DDA06/16 product page on our website for information

about the software that supports the device.

Install the software before you install your device

The driver needed to run the PCIM-DDA06/16 is installed with the software. Therefore, you need to install the

software package you plan to use before you install the hardware.

Configuring the hardware

The PCIM-DDA06/16 board has six banks of five switches for setting the gain for each DAC, and one

simultaneous transfer jumper to set the DAC update mode. Each analog channel also has an associated gain and

offset potentiometer for calibrating the channel, if necessary.

The PCIM-DDA06/16 is shipped with the following factory-default settings:

Switch/jumper factory-configured defaults

Board label Switch/jumper description Default setting

XFER or UPDATE

Simultaneous or individual DAC update

jumper

UPDATE position (single channel update)

CH0 through CH5

(S1 through S6)

Analog output range DIP switches ±5V

Before installing the PCIM-DDA06/16 in the computer, verify that the board is configured with the settings that

you want. Review the following information to change the default configuration of a jumper or switch on the

PCIM-DDA06/16 board.

Simultaneous transfer jumper

The simultaneous transfer jumper controls whether to update DAC channels individually (default) or as a group.

This jumper is shown in Figure 2 configured in its default UPDATE position.

Figure 2. Simultaneous transfer jumper

PCIM-DDA06/16 User's Guide Installing the PCIM-DDA06/16

Set the jumper to XFER to update the DAC voltage outputs as a group.

New output data is held until all DACs are loaded with their new digital data.

The data for each DAC is simultaneously transferred and the DAC voltage outputs are updated as a group

when any of the addresses BADR3 + 0 to BADR3 + B are read. Writing new digital values to the DAC

control register does not cause an update of the DAC's voltage output. Update of the output occurs only

after the DAC control register address (any of the addresses BADR3 + 0 to BADR3 + B) is read

In this way, the PCIM-DDA06/16 can be set to hold new values until all channels are loaded, then update

all six channels simultaneously. This is a very useful feature for multi-axis motor control.

Set the jumper to UPDATE to update the DAC voltage outputs individually.

The analog outputs are controlled by writing a digital control word as two bytes to the DAC's control

low byte, then high byte) are written to the DAC control register when the simultaneous transfer jumper is

in the default UPDATE position.

Analog output range switch

You set the analog output voltage range of each with a five-position DIP switch. The switches are located on the

board directly above the DACs and are labeled CH5 through CH0 (S6 through S1). Bipolar ranges are ±10 V

and ±5 V. Unipolar ranges are 0 to 10 V and 0 to 5 V.

Figure 3 lists the range value and associated settings for each switch.

Figure 3. Analog output range switch—one per DAC

To set a channel to a particular range, read the switch positions as U(up) or D(down) from left to right in the

row beside the range you want to set.

Installing the hardware

Install the MCC DAQ software before you install your board

The driver needed to run your board is installed with the MCC DAQ software. Therefore, you need to install the

MCC DAQ software before you install your board. Refer to the Quick Start Guide for instructions on installing

the software.

After you configure the board's switches and jumpers, install the PCIM-DDA06/16 into your computer. Perform

the following steps to install the board:

1. Turn your computer off, open it up, and insert your board into an available PCI slot.

2. Close your computer and turn it on.

When connected for the first time, a Found New Hardware dialog opens when the operating system detects

the device. When the dialog closes, the installation is complete. If you have not installed the MCC DAQ

software, cancel the dialog and install it now.

3. To test your installation and configure your board, run the InstaCal utility installed in the previous section.

Refer to the Quick Start Guide that came with your board for information on how to initially set up and

load InstaCal.

PCIM-DDA06/16 User's Guide Installing the PCIM-DDA06/16

If your board has been powered-off for more than 10 minutes, allow your computer to warm up for at least

15 minutes before acquiring outputting analog data with this board. This warm-up period is required for the

board to achieve its rated accuracy. The high-speed components used on the board generate heat, and it takes

this amount of time for a board to reach steady state if it has been powered off for more than 10 minutes.

Signal connections

The table below lists the board connector, applicable cables, and compatible accessory products.

Board connector, cables, and accessory equipment

Connector type

37-pin male D connector

Compatibility

Pinout identical to CIO-DDA06/16

Compatible cables

C37FF-x

C37FFS-x

DFCON-37 (D-connector, D-shell, and termination pins to construct your own

cable)

Compatible accessory products

with the C37FF-x cable or

C37FFS-x cable

CIO-MINI37

CIO-TERMINAL

SCB-37

SSR-RACK24

ENC-MINI37

Information on signal connections

General information regarding signal connection and configuration is available in the Guide to DAQ Signal

Connections (available for download from www.mccdaq.com/support/DAQ-Signal-Connections.aspx.)

The I/O connector is a standard 37-pin male connector that is accessible through the PC/AT expansion bracket.

Figure 4. I/O connector pinout

PCIM-DDA06/16 User's Guide Installing the PCIM-DDA06/16

The analog outputs of the PCIM-DDA06/16 are two-wire hook-ups. Always use analog ground (LLGND) as the

ground reference for all analog hook-ups.

Cabling

Figure 5. C37FF-x cable

Figure 6. C37FFS-x cable

Field wiring, signal termination, and conditioning

You can use the following cabling, screw termination, and signal conditioning products with the PCIM-

DDA06/16.

CIO-MINI37 – 37-pin screw terminal board.

CIO-TERMINAL – 37-pin screw terminal board with on-board prototyping area.

SCB-37 – 37 conductor, shielded signal connection/screw terminal box that provides two independent 50-

pin connections.

SSR-RACK24 – 24-channel, solid-state relay mounting and interface board for digital signal conditioning.

ENC-MINI37 – Enclosure for the MINI37.

DFCON37 – Connector kit that includes a 37-pin female D-connector, D-shell, 37 crimp pins, and cable

termination kit to construct your own cable.

Details on these products are available on our website.

Chapter 3

Specifications

All specifications are subject to change without notice.

Typical for 25 °C unless otherwise specified.

Specifications in italic text are guaranteed by design.

Analog output

Table 1. Analog output specifications

Parameter Specification

D/A converter type

AD660BR

Resolution

16 bits

Number of channels

Voltage ranges

±10 V, ±5, 0 to 10 V, 0 to 5 V. Ranges are switch selectable

D/A pacing

Software paced

Throughput System-dependent. Using the Universal Library programmed output

function (cbAOut()) in a loop, in Visual Basic, a typical update rate

of 150 kHz (± 70 nS jitter) can be expected. The rate was measured on

a 500 MHz Pentium III based PC.

Data transfer

Programmed I/O

Monotonicity

15 bits guaranteed over temperature

Slew rate

1.7 V/µs min, 2.4 V/µS typ

Current drive

±5 mA min

Output short-circuit duration

Indefinite

Power-on reset voltage

0 V ±15 mV

Miscellaneous

Double buffered output latches

Update DACs individually or simultaneously (jumper selectable)

Accuracy

Table 2. Analog output accuracy specifications

Parameter Specification

Absolute accuracy

±2.0 LSB max

Typical accuracy

±1.0 LSB max

Gain error

Trimmable by potentiometer to 0

Offset error

Trimmable by potentiometer to 0

Integral linearity error

±1.0 LSB max, ±0.5 LSB typ

Differential linearity error

±1.0 LSB max, ±0.5 LSB typ

Each PCIM-DDA06/16 is tested at the factory to assure the board’s overall error does not exceed ±2.0 LSB.

Total board error is a combination of gain, offset, integral linearity and differential linearity error. The

theoretical worst-case error of the board may be calculated by summing these component errors. Worst case

error is realized only in the unlikely event that each of the component errors are at their maximum level and

causing error in the same direction.

Typical accuracy is derived directly from the various component typical errors. This typical, maximum error

calculation for the PCIM-DDA06/16 yields ±1.0 LSB.

Tabla de contenidos

Otros manuales de Sistema de E/S de Measurement Computing

Measurement Computing

Measurement Computing CIO-DAS08 Manual de usuario

Measurement Computing

Measurement Computing USB-231 Manual de usuario

Measurement Computing

Measurement Computing USB-1208HS-4AO Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS08 Manual de usuario

Measurement Computing

Measurement Computing USB-231-OEM Manual de usuario

Measurement Computing

Measurement Computing USB-DIO24H/37 Manual de usuario

Measurement Computing

Measurement Computing PCI-PDISO16 Manual de usuario

Measurement Computing

Measurement Computing USB-1616HS-2 Manual de usuario

Measurement Computing

Measurement Computing USB-DIO96H Manual de usuario

Measurement Computing

Measurement Computing PC-CARD-D24/CTR3 Manual de usuario

Measurement Computing

Measurement Computing PCI-DIO48H Manual de usuario

Measurement Computing

Measurement Computing PCI-DIO24 Manual de usuario

Measurement Computing

Measurement Computing USB 1024ls Manual de instrucciones

Measurement Computing

Measurement Computing USB-1408FS-Plus-OEM Manual de usuario

Measurement Computing

Measurement Computing USB-3103 Manual de usuario

Measurement Computing

Measurement Computing USB-1208FS-Plus-OEM Manual de usuario

Measurement Computing

Measurement Computing USB-1616HS Manual de usuario

Measurement Computing

Measurement Computing USB-DIO96H/50 Manual de usuario

Measurement Computing

Measurement Computing PCIe-DIO24 Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS1000 Manual de usuario

Measurement Computing

Measurement Computing USB-3104 Manual de usuario

Measurement Computing

Measurement Computing E-DIO24 Manual de usuario

Measurement Computing

Measurement Computing USB-1208HS-4AO Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS6030 Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

M-system

M-system R3Y-RS8 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario

WAGO

WAGO I/O-SYSTEM 750 Manual de usuario