MCZ JAZZ Hydromatic 30 H1 Guía de configuración

Instructions in English

PELLET STOVE

JAZZ Hydromatic 30 Acs H1

JAZZ Hydromatic 30 H1

PART 2 - OPERATION AND CLEANING

GBINSTALLATION GUIDE

TABLE OF CONTENTS

TABLE OF CONTENTS .................................................................................................. II

12PRECAUTIONS BEFORE STARTUP............................................................................3

13CONTROL PANEL ....................................................................................................4

14FIRST IGNITION .....................................................................................................5

15MENU STRUCTURE .................................................................................................8

16INFORMATION MENU ...........................................................................................12

17SETTINGS MENU ..................................................................................................15

18TECHNICAL MENU ................................................................................................29

19SAFETY DEVICES AND ALARMS..............................................................................31

20RECOMMENDATIONS FOR SAFE USE.......................................................................36

21CLEANING AND MAINTENANCE..............................................................................37

22FAULTS/CAUSES/SOLUTIONS .................................................................................45

23CIRCUIT BOARD ...................................................................................................48

12-PRECAUTIONS BEFORE START-UP

GENERAL WARNINGS

Remove any objects that may burn from the product and from the glass(manual, various adhesive labels or any polystyrene).

Check that the brazier is positioned correctly and rests properly on the base.

The rst ignition may not be successful as the feed screw is empty and does not always manage to load the brazier

with the required amount of pellets in time to light the ame.

CANCEL THE FAILED IGNITION ALARM. REMOVE THE PELLETS LEFT IN THE BRAZIER AND REPEAT THE IGNITION.

If after repeated attempts, the ame fails to ignite, despite a regular ow of pellets in the brazier, which must rest snugly against the

slots and be clean without any ash incrustations. If no anomaly is found during this inspection, there may be a problem with the

product components or installation may not be correct.

REMOVE THE PELLETS FROM THE BRAZIER AND CONTACT AN AUTHORISED TECHNICIAN.

Do not touch the stove during the rst lighting, as it is during this phase that the paint sets. If you touch the paint,

you may expose the steel surface.

If necessary, touch up the paint with the spray can of the specic colour. (See‘’Pellet stove accessories’’).

It is good practice to ensure eective ventilation in the room during the initial start-up, as the stove will emit some

smoke and smell of paint.

ATTENTION!

Please ensure the brazier is clear of ALL pellets and ash build up following any failed ignitions. Failure to clear out

the brazier prior to resetting may result in further failed ignitions or explosive ignition under certain conditions.

Do not stand close to the stove and, as mentioned, air the room. The smoke and smell of paint will disappear after about an hour of

operation, however, they are not harmful in any case.

The stove will be subject to expansion and contraction during the lighting and cooling down stages, and may therefore make slight

creaking noises.

This is absolutely normal as the structure is made of laminated steel and must not be considered a defect.

It is extremely important to make sure the stove does not reach high temperatures straight away, but to increase the temperature

gradually using low power at rst.

This will prevent damaging the ceramic or serpentine stone tiles, the welds and the steel structure.

DO NOT EXPECT HEATING EFFICIENCY IMMEDIATELY!!!

ATTENTION!

If during operation or initial ignition you encounter combustion smoke spillage in to the room from the

applianceor theue thenpleaseswitch otheappliance, ventilatethe room andcontact the installation

/ service technician immediately.

B C DE

13-CONTROL PANEL

CONTROL PANEL DISPLAY

KEY

A - DISPLAY; indicates a series of information on the stove, as well as the identication code of any malfunction.

B - Function selection key indicated by the upper display (i.e. start-up/shutdown)

C - Function selection key indicated by the upper display (i.e. increase/scrolling)

D - Function selection key indicated by the upper display (i.e. decrease/scrolling)

E - Function selection key indicated by the upper display (i.e. menu)

REV.SOFTWARE NUM BANCA DATI

ITALIANO

ENGLISH

ESPANOL

CDE

LANGUAGE

14-FIRST IGNITION

FIRST START-UP

At initial start-up, after connecting the power cable and pressing the I/O button, the stove display will show wording for the software

version and database number (after a few seconds it will move on to the next screen).

If the language has already been set, the next screen will be OFF, otherwise one enters the following parameter.

SELECT LANGUAGE

At initial start-up, if it has never been set, the LANGUAGE choice screen appears.

The system displays all possible languages.

Using the arrow keys (C, D) scroll the languages and conrm the desired language using the“E”(OK) key.

SETTING TIME AND DAY

The keys that are active for this function are:“C”,“D”,“E”. The C-D keys are used to choose time or day while the E key is used to conrm.

21.25

CDE

TODAY IS MONDAY AND IT IS

CHANGE

DAY

CHANGE

TIME

21.25

CDE

TODAY IS MONDAY AND IT IS

21.25

CDE

TODAY IS MONDAY AND IT IS

OFF

ECO

14-FIRST IGNITION

SCREEN OFF

If a LANGUAGE has already been set, the display will go to OFF.

By pressing any one of the keys (B, C, D, E) the rst screen will appear with the wording OFF displayed. From this screen, pressing keys “B”

and“E”(respectively corresponding to ON and MENU) will make it possible to access the panel or the menu. If no key is pressed, the display

will once again show OFF after 5 seconds.

PRELIMINARY OPTIONS

Hydro Air stoves are characterised by the presence of a heating hydraulic circuit and a room air fan for distributing hot air.

Room fan

The speed can be set manually or automatically.

In manual mode the speed, from 0 to 5, is chosen by the user from the control panel. The fan is only activated if the temperature read by

the smoke probe exceeds 100°C and is deactivated when it goes below 80°C; while at speed 0 the fan is o, if the ame power is below

40% otherwise it will run at speed 1.

The stove adjusts the fan speed automatically according to the power of the ame.

Even in this case the fan is only activated if air temperature of the smoke probe exceeds 100°C.

AUTO

EXIT OK

SET VENTILATION

EXIT OK

SET VENTILATION

OFF-DISPLAY ACTIVEOFF-DISPLAY OFF

OFF

ECO

14-FIRST IGNITION

OFF MENU

10:13 TIMER1 ECO

25°

23° AUTO

TEMP AIR

Lighting the stove

To switch on the stove, keep the“B”(ON) key on the panel pressed.The stove starts an ignition procedure that brings the ame to a suitable

level to Supply Power.

Supplying power

The power supply of the stove is indicated by “power level bars”: one bar corresponds to minimum power, 5 bars to maximum power;

this level is determined by the heating system heat requirements, the stove adjusts pellet loading parameters, fumes extraction, and

combustion air ow to comply with this requirement.

UPPER BAR: active requirements, active programmes, power bar, functions

CENTRAL BAR: room temperature, room set, room fan bar

LOWER BAR/KEYS: shut-o “B”, modify ambient temperature setting“C”and fan

setting“D”, menu“E”

1 = power level bars

OFF

ECO

15-MENU STRUCTURE

MENU STRUCTURE

To enter MENU press the“E”key (MENU).

Next, this screen with the following functions is displayed:

Sub-menu

TEMPERATURES

PROGRAMS

INFORMATION

SETTINGS

TEMPERATURES

When accessing this function, the main screen makes it possible to set heating and domestic water temperature (if the boiler with probe

is congured - see menu settings input aux).

Select what is to be set and then using the C and D keys increase/decrease the temperature, use the E key to conrm while the B key is

used to exit and return to the main MENU.

PROGRAMS

In this case it is possible to choose the programme to be set.

Programme selection makes it possible to choose between one of the following options (one choice excludes the other):

TIMER 1

TIMER 2

MANUAL

TEMP. LEVELS

SLEEP FUNCT.

TEMPERATURES

INFORMATION

PROGRAMS

SETTINGS

EXIT OK

TEMPERATURES

EXIT OK

71°

TEMPERATURE BUFFER

EXIT OK

TEMPERATURES

50°

16° OFF

OFF

03:33 TIMER 1

15-MENU STRUCTURE

In the MENU screen, move the cursor with arrows“C”-”D”and select PROGRAMS, press ok“E”to conrm. Next select the programme you

wish to set.

Once completed, always press “ACTIVATE” to conrm the choice of programme.

The TIMER 1 and 2 programs are freely programmable for each 1/2 hour of the day on three dierent temperature indicators (T1-T2-T3)

and in dierent ways for each day of the week.The OFF level requires that the stove is switched o in that interval.

Example of temperature programming for Monday.

Select the TIMER 1 item from the PROGRAM menu and press the ENTER “E”key, using arrow “D”highlight Monday and press OK (“E”) to

enter programming.

Using the centre arrow keys “C” and “D” select the half hour interval to be selected and use the “E” key to set the temperature T1-T2-T3

(depending on whether the key is pressed 1-2-3 times, the corresponding temperature can be read in the bottom right of the display).

Once temperature programming for Monday is complete press the ‘’B’’ SALVA (SAVE) key. If the same temperature scale of Monday is

desired for other weekdays, after saving (“E” key) press the “C” key (COPIA-COPY), select the day where the programme is to be copied

using the“D”key and press the“C”key (INCOLLA-PASTE). Repeat the same procedure until the programmes for all weekdays are complete.

At this point the stove is programmed according to your temperature needs, which can be modied at any time.

ATTENTION:

In order to make stove use easier, MCZ supplies Timer 1 with preset weekly temperatures and times (according to the table below), while

Timer 2 is empty. In any case, it is possible to change times and temperatures of Timer 1 at any time.

PANEL OFF DISPLAY FROM TIMER

When timer 1 (for example) has no set temperature, the panel highlights that the stove is in OFF position.

If the stove is o by MANUAL command, the timer will

have no eect.

For the stove to come on with the timer, the panel

must display the image shown on the side; if this

should not be the case, it may be necessary to press

the ON (“B”) key.

PROGRAM SELECTION

EXIT ENTER

TEMPERATURES

INFORMATION

PROGRAMS

SETTINGS

EXIT OK

TIMER 1 TIMER 2 MANUAL

TEMP.LEVELS FUNCT. SLEEP

ACTIVATE

COPY OK

MONDAY TUESDAY WEDNESDAY

0 246 12 18

SAVE

MONDAY

0 246 12 18

TIMER 1

EXIT

10:00 20°C

TIMER 1

6 12

10:00

15-MENU STRUCTURE

Time table

23:00

22:00

21:00

20:00

19:00

18:00

17:00

16:00

15:00

14:00

13:00

12:00

11:00

10:00

09:00

08:00

07:00

06:00

05:00

04:00

03:00

02:00

01:00

00:00

Weekly programmes

Temperatures

OFF

Days

Sunday

Monday

Tuesday

Wednesday

Thursday

Friday

Saturday

* T1=16°C T2=20°C T3=22°C OFF=switched o

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cocina de MCZ

MCZ

MCZ EGO COMFORT AIRMATIC 10 M3 CORE Guía de configuración

MCZ

MCZ EGO Manual de usuario

MCZ

MCZ SUITE Guía

MCZ

MCZ RAY COMFORT AIR 8 M1 Manual de usuario

MCZ

MCZ GIO 2016 Manual de usuario

MCZ

MCZ CLUB COMFORT AIR MATIC 14 M1 Manual de usuario

MCZ

MCZ Polar Guía

MCZ

MCZ CLUB AIR 10 M1 Guía de configuración

MCZ

MCZ JAZZ Hydromatic 30 M1 Manual de usuario

MCZ

MCZ Veld Manual técnico

MCZ

MCZ TECLA AIR 6 M1 Especificaciones técnicas

MCZ

MCZ CUTE AIR 8 M1 Especificaciones técnicas

MCZ

MCZ EGO Hydromatic 12 M2 Manual de usuario

MCZ

MCZ STAR AIR 8 M1 Manual de usuario

MCZ

MCZ SUITE COMFORT AIRMATIC 12 M3 CORE Manual de usuario

MCZ

MCZ SUITE/CLUB/MUSA AIR 10 M3 Manual de usuario

MCZ

MCZ LINEA Comfort Air Manual de usuario

MCZ

MCZ MUSA COMFORT AIR MATIC 14 M1 Especificaciones técnicas

MCZ

MCZ STAR Hydromatic 12 M2 Manual de usuario

MCZ

MCZ SUITE AIR 10 UP! M1 Manual de usuario

MCZ

MCZ CLUB COMFORT AIRMATIC 14 M2 Guía de configuración

MCZ

MCZ DECO' AIR 8 M1 Especificaciones técnicas

MCZ

MCZ HALO AIR 8 M1 Manual de usuario

MCZ

MCZ KLIN COMFORT AIR 8 M1 Manual de usuario

Manuales populares de Cocina de otras marcas

Arada

Arada Cassette Stove Manual de usuario

Parmco

Parmco FS 600 Manual de usuario

HearthStone

HearthStone Stowe DV 8321 Guía de solución de problemas

Cattara

Cattara FAMILY Manual de usuario

Stanley

Stanley Argon F500 OVAL Manual de usuario

Avalon

Avalon B-VENT Manual de usuario

Nordpeis

Nordpeis Vega Manual de usuario

Exquisit

Exquisit EKC601-5 Manual de operación

Stanley

Stanley Oisin Oil MK II Manual del propietario

Thermocet

Thermocet Brookfield S/CC Manual de usuario

HASE

HASE delhi Manual de usuario

Vermont Castings

Vermont Castings Intrepid 2 Manual de usuario

Italiana Camini

Italiana Camini CLASSICA Guía de inicio rápido

Avalon

Avalon Vashon Avanti DVS FS Manual de usuario

Spartherm

Spartherm ambiente a1 Manual de usuario

Dimplex

Dimplex MCFSTV12AU Manual de usuario

Warmlite

Warmlite WL46040 Manual de usuario

Regency

Regency Ultimate U39E Series Guía de inicio rápido