MBM FC 10 PLUS Manual de usuario
OPERATION MANUAL
MBM TABLETOP COLLATOR
MODEL FC 10 PLUS
REVISED:Sep 09, 2016
Read this “Operation Manual” carefully before use.
Keep it at a specific place for handy reference.
1
2
In this operation manual, warning markings as shown below are used to enable you to properly use the
device and thereby prevent harm to the human body and damage to assets. Before using the device,
carefully read the descriptions of these warning markings to thoroughly become familiar with correct use.
This marking indicates the possibility of death or serious injuries if the device
is improperly handled in disregard of this marking.
This marking indicates the possibility of injuries and physical damage if the
device is improperly handled in disregard of this marking.
This Collator is a product to be used in the tabletop.
Read this “Operation Manual” carefully before use.
Notes, safely received correct use of the product, is intended to prevent harm or damage in advance.
In this manual following names and signs stand for possible dangers.
This symbol indicates a prohibited act. A pictogram describing the
specific prohibited act is shown in the figure. (The left figure shows that
disassembly is prohibited.)
This symbol an act the user is forced or instructed to perform. A pictogram describing
the specific prohibited act is shown in the figure. (The left figure instructs the user to
disconnect the power plug from the outlet.)
About warning marking
Warning
Caution
3
Safety Instructions
Warning
Operate the collator with designated AC current only. Use an exclusive outlet, as overloading may cause
fire or an electrical shock.
Do not install the machine in an unstable place, such as one that shakes or tilts. The machine may fall,
causing breakage or physical injury.
Never unplug the power cord from the outlet by gripping the cord itself. Doing so may
damage the cord, causing fire or injury. Always disconnect the machine by gripping the
plug.
Do not place receptacles containing water, such as vases, flowerpots and cups, on the
machine. Spilled water can cause fire or an electrical shock.
Do not fail to connect the grounding wire. Connect the grounding wire before connecting the power plug to
the power supply. When disconnecting the grounding wire, first disconnect the power plug from the power
supply. A fire or electric shock may occur in case of electric leakage if the grounding wire is not connected.
Do not remove the cover of the machine, as it can cause an electrical shock or injury.
Do not dismantle the machine, it may cause fire or an electrical shock.
Continuing operation in spite of irregularities, such as overheating, smoking and unusual
odor, may cause fire or an electrical shock. In such cases, turn off the power switch, remove
the plug from the outlet and contact your dealer or authorized service representative.
When foreign substances, such as metal fragments, water or other liquids, fall into the
machine, turn off the power switch immediately, remove the plug from the outlet and contact
your dealer or authorized service representative. Continued operation with such substances
in the machine may cause fire or an electrical shock.
4
Caution
Do not touch any part of the drive, including the roller, with a hand. It may cause an injury.
Do not allow hair, a necktie, a necklace or other things to get too close to the drive, including
the roller, as bodily injury can result.
Make sure that the paper feed table, auxiliary table, stacking table and the plate to prevent
the machine from falling are properly set. They may cause an injury if they come off.
Do not install the machine in a humid or dusty place; excessive humidity and dust can cause
fire or physical injury.
Do not put your fingers or hands in the clearance around the sheet feed and discharged sheet tables. You
may get injured.
When you put your hand inside the device to, for example, remove a sheet, be careful not to touch
projections or steel plate edges. You may get injured.
Never unplug the power cord from the outlet by gripping the cord itself. Doing so may
damage the cord, causing fire or injury. Always disconnect the machine by gripping the
plug.
Make sure that the paper feed table, auxiliary table, stacking table and the plate to prevent
the machine from falling are properly set. They may cause an injury if they come off. Also,
take care not to cause the machine to fall when attaching or removing the stacking table and
auxiliary table.
Be sure to remove the power plug from the outlet when moving the machine, otherwise it
may damage the cord, causing fire or an injury.
When the collator will not be used for several days, such during consecutive holidays, etc., be
sure to unplug the power cord from the outlet for safety’s sake.
5
INTRODUCTION
Read this “Operation Manual” carefully before use.
Keep it at a specific place for handy reference.
Since the specifications of this machine are subject to change, be sure not to mistake this manual
for one of a different model, as descriptions of may differ.
CONTENTS
1. PRECAUTIONS FOR INSTALLATION AND USE................................... 7
1.1 Installation ........................................................................................................................................ 7
1.2 Place for installation ......................................................................................................................... 8
1.3 Confirmation of contents and quantity of attachments ..................................................................... 9
2. COMPONENTS ...................................................................................................................... 10
2.1 Overview......................................................................................................................................... 10
2.2 Operation Panel .............................................................................................................................. 12
3. MATTERS TO NOTE ............................................................................................................. 14
3.1 Definitions ...................................................................................................................................... 14
3.2 Characteristics and purpose of use .................................................................................................. 14
3.3 When not in use .............................................................................................................................. 14
4. PREPARATIONS FOR USE..................................................................................... 15
4.1 Installing attachments ..................................................................................................................... 15
4.1.1. Mount the plate to prevent the machine from falling ...................................................................... 15
4.1.2 Power connection ............................................................................................................................ 15
4.1.3 Stacking table assembly. ................................................................................................................. 15
4.1.4 Stacking table .................................................................................................................................. 16
4.1.5 Paper feed table ............................................................................................................................... 17
4.2 Setting paper feed pressure ............................................................................................................. 18
4.3 Setting separator pressure ............................................................................................................... 18
5. OPERATIONS......................................................................................................................... 19
5.1. Procedure and method .................................................................................................................... 19
5.1.1. Activating power ............................................................................................................................ 19
5.1.2 Setting of paper on feed tables ........................................................................................................ 19
5.1.3 Setting of stacking guides, poles, etc.. ............................................................................................ 20
5.1.4 Collation ......................................................................................................................................... 21
5.2 Counter ........................................................................................................................................... 22
5.2.1. Using adding mode ......................................................................................................................... 22
5.2.2. Using subtracting mode .................................................................................................................. 22
5.3 Setting collation speed .................................................................................................................... 22
5.4 Setting normal or alternate collation mode ..................................................................................... 23
5.5 Crisscross stacking (or straight stacking) .................................................................................... 24
5.6 Insert mode ..................................................................................................................................... 24
5.7 Programmed insert mode ............................................................................................................... 26
5.8 Storing Insert/Programmed Insert mode data ................................................................................. 27
5.9 Calling up the Insert/ Programmed Insert mode data ..................................................................... 28
5.10 Repeat mode ................................................................................................................................... 28
5.11 Switch Independent／Synchronized ............................................................................................... 29
6
6. MAINTENANCE, INSPECTION, CONSUMABLES .................................................. 30
6.1 Important for maintenance and inspection ...................................................................................... 30
6.2 Usual maintenance .......................................................................................................................... 30
6.3 Consumables ................................................................................................................................... 32
7. TROUBLE SHOOTING.......................................................................................................... 32
7.1 Corrective actions to be taken when LED lamps are lit or flashing ................................................ 32
7.2 Troubleshooting .............................................................................................................................. 34
7.3. In case of breakdown ...................................................................................................................... 36
8. RELOCATION OR DISPOSAL.............................................................................................. 36
8.1 Relocation ....................................................................................................................................... 36
8.1.1 Removal of the machine from its present location ......................................................................... 36
8.1.2 Transport ......................................................................................................................................... 36
8.1.3 Installation ...................................................................................................................................... 36
8.2 Disposal .......................................................................................................................................... 36
9. PRODUCT SPECIFICATIONS.............................................................................................. 37
9.1 Specifications .................................................................................................................................. 37
7
1. PRECAUTIONS FOR INSTALLATION AND USE
1.1 Installation
Caution
Use the optional collator table exclusively designed for this machine and do not install the machine
in an unstable place, such as one that shakes or tilts. The machine may fall, causing a damage or
bodily injury.
Do not install the machine in a humid or dusty place, as excessive humidity and dust may cause fire
and physical injury.
・When installing the collator, use a collator table designed for the collator (sold as option).
The collator table has safety measures such as metal fittings to prevent the machine from falling, etc.
and is designed to keep its level position when used as a single machine as well as when connected with
post-processing machine such as stapler-puncher, etc.
・When using the collator, or working near the collator, do not lean over the collator as it may overturn.
・When relocating the collator, move it while holding the collator table as pushing the upper part of the
collator may overturn it.
・If the collator is likely to overturn when installed, fix the collator to the wall using the wall fixing plate
(sold separately).
8
1.2 Place for installation
This machine is also designed for IT power system.
Avoid installing the machine in the following places for the sake of safety and to prevent mechanical
problems.
[Precautions for installation]
・Locations with extremely high or low temperatures. Room temperature should be between 5 and 35
degrees centigrade.
・Locations with the potential for producing electrical leaks, for example, owing to splashing water.
・Near heat sources
・Places exposed to wind
・Narrow spots with poor ventilation, or dark places
・Locations exposed to direct sunlight or other powerful light sources. Direct sunlight or other strong
light sources may cause the optical sensor to malfunction. Install the machine in an appropriate place
or shield the light with a heavy curtain or other material.
BE SURE TO FOLLOW THESE INSTRUCTIONS TO AVOID MALFUNCTION.
9
1.3 Confirmation of contents and quantity of attachments
After unpacking the collator, check the attachments.
Should any part be missing, contact your dealer immediately.
Operation manual
Plate to prevent the machine
from falling (front)
With Screws to fit (4pieces)
Plate to prevent the machine
from falling (rear)
With Screws to fit (4pieces)
Guide fix screw
(2pieces)
Otros manuales para FC 10 PLUS
1
Tabla de contenidos
Otros manuales de Máquina plegadora de papel de MBM
Manuales populares de Máquina plegadora de papel de otras marcas
KRUG+PRIESTER
KRUG+PRIESTER IDEAL 8570 Manual de usuario
Pressure Seal Systems
Pressure Seal Systems PS300 Manual de usuario
Olympia
Olympia FM 4420 Manual de usuario
Horizon Fitness
Horizon Fitness QC-S30 Manual de funcionamiento
Cyklos
Cyklos CFM 600 Manual de usuario
Dynafold
Dynafold Paper Folder PF-330 Manual de usuario
