MAYSER SG-RST 153 Manual de usuario

Control unit SG-RST 153

Original instructions

1004931 SG-RST 153 AC 230 V AC/DC 12 to 24 V

Mayser GmbH & Co. KG

Örlinger Straße 1–3

89073 Ulm

GERMANY

Phone: +49 731 2061-0

Fax: +49 731 2061-222

E-mail: info.ulm@mayser.com

Internet: www.mayser.com

Innovative by tradition.

Version 0.3

EN | Operating instructions

Page 2/15 Operating instructions SG-RST 153 171019 v2.00-RiA

The reproduction, distribution and utilization of this document as well as the communication of its contents with-

out express authorization are prohibited. Oenders will be held liable for the payment of damages. All rights re-

served in the event of the grant of a patent, utility model or design.

Safety ﬁrst!

•Read the manual carefully before use.

•Warning signs in the manual warn of unexpected dangers. Always ob-

serve warning signs.

•Retain the manual throughout the service life of the product.

•Pass the manual on to every subsequent owner or user of the product.

•Insert every supplement received from the manufacturer into the man-

ual.

•Observe chapter on Safety starting on page 5.

Conformity

The Declaration of Conformity is available in the download section of the website:

www.mayser.com/en/downloads

The design type of the product complies with the basic requirements of the following

directives:

•2006/42/EC (Safety of Machinery)

•2011/65/EU (RoHS)

•2014/30/EU (EMC)

171019 v2.00-RiA Operating instructions SG-RST 153 Page 3/15

Contents

About this manual 4

Safety 5

Intended use 5

Safety instructions 5

Residual dangers 6

Parts supplied 7

Storage 7

Product overview 7

Connections 7

LED indicators 8

Operation 8

Installation 8

Testing 10

Connection examples 10

Commissioning 11

Testing 11

Pressure-sensitive protection device actuated 12

Correlations 12

Decommissioning 12

Recommissioning 12

Maintenance and cleaning 13

Maintenance 13

Cleaning 13

Troubleshooting and remedies 13

Replacement parts 14

Disposal 14

Technical data 14

Page 4/15 Operating instructions SG-RST 153 171019 v2.00-RiA

About this manual

Symbols used Symbol Meaning

Ä... Action with one or more steps whose order is not rele-

vant.

1. ... Action with several steps whose order is relevant.

• ...

-...

Bullets ﬁrst level

Bullets second level

(see Section Installation) Cross-reference

Danger symbols and

information

Symbol Meaning

DANGER Immediate danger leading to death or serious injury.

WARNING Imminent danger which may lead to death or serious injury.

CAUTION Possible danger which may lead to minor or moderate inju-

ries.

NOTE Potential danger of property damage or environmental deg-

radation.

Information on easier and safer working practices.

Other applicable

documents

ÄAlso observe the following documents:

-Drawing of the sensor system (optional)

-Wiring diagram (optional)

-Installation instructions of the sensors used

Target group This manual is intended for the owner and electricians. The electrician must be famil-

iar with the installation and commissioning.

Validity This manual is valid only for the product speciﬁed on the title page.

This manual is an integral part of the product.

Mayser will assume no liability and provide no guarantee whatsoever for damages

and consequential damages resulting from failure to comply with the manual.

About this manual

Dimensions in drawings

Unless otherwise indicated, all dimensions are stated in millimetres (mm).

171019 v2.00-RiA Operating instructions SG-RST 153 Page 5/15

Safety

Without a test signal, the control unit corresponds only to category 1.

The control unit is designed only for safety edges with an 8k2 monitoring resistor.

Safety mats and safety bumpers may not be connected.

The performance level PL is dependent on the output of the connected load. PL d can

also be achieved in some cases. We will be glad to assist you.

Intended use

The control unit is designed for signal processing of a pressure-sensitive protective

device. It evaluates the output signals of sensors with monitoring resistor 8k2. The

integrated output signal switching device (OSSD) transmits the evaluated safety sig-

nals directly to the downstream control.

The product complies with ISO13849-1:2015 Category2 PLc. So that the safety

classiﬁcation is retained, the downstream control must be of the same or a higher

category.

Safety

Safety instructions

ÄDo not use in ATEX zones

Do not use the Control Unit in potentially explosive environments (ATEX). The

control unit is not authorised for use in these zones.

ÄDisable in case of error

Disable the safety device in case of malfunctions or visible damage.

ÄPrevent restarting of the machine

As long as a hazard continues to exist, take measures to prevent the machine

from restarting, for example by means of a startup lockout.

ÄPrevent electric shock

When working on electrical systems, always disconnect them from the power

supply and secure them against being switched on again, to prevent injuries from

electric shock.

For your own safety the following safety instructions apply.

ÄEnsure careful conﬁguration of interface

The quality and reliability of the interface between the safety device and the ma-

chine aects the overall safety. Take special care when setting up this interface.

Page 6/15 Operating instructions SG-RST 153 171019 v2.00-RiA

Safety

Terminals X1 to X2 are not potential-free.

ÄDo not modify the control unit

Never manipulate or make changes to the control unit.

Residual dangers

There are no known residual dangers associated with this product.

ÄDo not cross link control unit

Do not cross link the control unit with other control units.

ÄFit spark absorbers

When connecting inductive loads, ﬁt spark absorbers (RC modules) to the con-

sumer.

ÄCheck supply voltage

Check supply voltage. It must correspond with the connecting voltage USon the

type plate.

ÄObserve pin assignment

Observe pin assignment when connecting the supply voltage.

ÄProtect relay contacts

Risk of welding: Protect the relay contacts externally.

ÄDo not overload control unit

Ensure that the speciﬁed switching current is not exceeded.

ÄDo not exceed the maximum number of sensors

Do not connect more sensors on the control unit, than the number speciﬁed in

the installation instructions of the sensors.

ÄMaintain distance

When installing in the switch cabinet, ensure sucient distance from heat sourc-

es (at least 2 cm).

ÄObserve degree of protection

Only use the control unit in rooms with a minimum degree of protection of IP54

(e.g. switch cabinet).

To prevent irreparable damage to the product, the following safety instructions ap-

ply.

171019 v2.00-RiA Operating instructions SG-RST 153 Page 7/15

Parts supplied

Connections: Terminals:

Switching channel 1 14, 13

Test signal T1, T2

Sensor X1, X2

Supply voltage AC/DC 12-24 V A1, A2

Supply voltage AC 230 V PE, N, L1

Parts supplied

1× Control unit

Enclosure with electronics module,

1× PG9 cable screw connection and

2× PG11 cable screw connection.

1× Operating instructions

1× Declaration of Conformity

ÄUpon receipt of the parts supplied, check immediately for completeness and

good condition.

Product overview

Connections

ÄStore the control units in the original package, in a dry place.

ÄComply with the storage temperature speciﬁed in the technical data.

Storage

Page 8/15 Operating instructions SG-RST 153 171019 v2.00-RiA

Operation

•red LED „FAULT“:

Cable break

•yellow LED „SENSOR“:

Sensor actuated or testing

•green LED „POWER“:

Supply voltage connected

The control unit can be operated with AC/DC 12 to 24 V or AC 230 V. If supply volt-

age is connected, the green “POWER” LED lights up. The control unit now monitors

the connected sensor, which must be equipped with an 8k2 monitoring resistor. In

sensors that are not actuated, relay K1 energizes and switching channel 1 is closed. If

the sensor is actuated, relay K1 de-energizes, the yellow “SENSOR” LED lights up, and

switching channel 1 is opened. In case of a cable break, relay K1 de-energizes, the red

“FAULT” LED lights up, and switching channel 1 is opened.

Prior to any dangerous movement the safety function of the sensor must be moni-

tored via an external test signal from the machine control.

Without a test signal, the control unit corresponds only to category 1.

Automatic reset

1. Mount the sensor in the desired position using screws with a diameter of 4 mm.

To do so, remove the enclosure cover.

Operation

The control unit operates without a reset function. If the sensor is released after actu-

ation, relay K1 energizes again with a delay of tw. (see reactivation time twin chapter

Technical data)

LED indicators

Installation

For your safety, the generally accepted safety rules also apply for assembly:

•Disconnect all devices and live parts in the immediate vicinity from the power

supply.

•Ensure that all devices and live parts cannot be switched back on.

•Test to ensure that all devices and live parts are disconnected from the power

supply.

171019 v2.00-RiA Operating instructions SG-RST 153 Page 9/15

Installation

Machine control

Test device

3. Wire the sensors, relay contacts and supply voltage to the cable terminals.

Page 10/15 Operating instructions SG-RST 153 171019 v2.00-RiA

Installation

Testing

ÄSet jumper JP1 according to the applied test signal.

Voltage for

test signal

Type

test signal

Position of

jumper JP1

Reaction of switch-

ing channel 1

Machine

control

Connection examples

Connection examples 1

Tabla de contenidos

Otros manuales de Unidad de control de MAYSER

MAYSER

MAYSER SG-RS 309-2 Manual de usuario

MAYSER

MAYSER SG-RS 309-2 Manual de usuario

MAYSER

MAYSER SG-EFS 104/4L Manual de usuario

MAYSER

MAYSER SG-RST 204 Manual de usuario

MAYSER

MAYSER SG-RSV 205 Manual de usuario

MAYSER

MAYSER SG-EFS 104 ZK2/1 8k2 Manual de usuario

MAYSER

MAYSER SG-EFS Manual de usuario

MAYSER

MAYSER SG-EFS 104/2W Manual de usuario

MAYSER

MAYSER SG-EFS 1 4 ZK2/1 L20ms Series Manual de usuario

MAYSER

MAYSER SG-EFS 104/2W Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario