Maxxus RunMAXX 90 PRO Instrucciones de instalación
ENG
MAXXUS 90 PRO
Bike
INSTALLATION & OPERATING MANUAL
2
Index
Index 2
Safety Instructions 3
Overall View of the Device 4
Fixing Materials 5
Tools Included in Delivery 5
Assembly 6 – 10
Seat Adjustment 11
Levelling 11
Transport, Location & Storage 12
Care, Cleaning & Maintenance 12
Cockpit 13 - 19
Pulse & Heart Rate 20 - 21
Training Recommendations 22 - 23
Technical Details 24
Disposal 24
FAQ 25
Recommended Accessories 25
Exploded Drawing 26
Spare Parts List 27 - 29
Warranty 30
31
Service Contract
© 2019 MAXXUS Group GmbH & Co. KG
All rights reserved / All rights reserved
This publication may not be reproduced, stored in a retrieval system, or transmitted in whole or in part, in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise without the prior written permission of Maxxus Group GmbH & Co. KG.
Errors, colour and technical modification subject to change, reproduction as well as electronic duplication only with written permission of MAXX-
US Group GmbH & Co. KG.
3
Safety Instructions
Before you start exercising, be sure to read the entire operating manual, especially the Safety Information, the Maintenance
and Cleaning Information and the Training Information. Also make sure that anyone else who uses this training device is famil-
iar with this information and observes it.
Always follow the maintenance and safety instructions in this manual very carefully.
This training device may only be used for its specific intended use. Any misuse can cause risk of possible accident, damage to
health or damage to the device for which the Distributor will not assume any liability.
Electrical Connection (only applies to devices with an external electrical connection)
− A mains voltage of 220-230V is required to operate this training device.
− The training device is only to be connected to the mains with the mains cable supplied using a 16A individually fused and
earthed socket installed by a qualified electrician.
− Always remove the electric plug from the socket before moving the training device.
− Remove the electric plug from the socket before commencing any cleaning, maintenance or other works.
− Do not connect the mains plug to a socket on a socket strip or on a cable drum.
− If using a cable extension please ensure that this complies with DIN standards, VDE regulations and guidelines, technical
rules issued by other European Union states.
− Always place the mains cable so it cannot be damaged or cause a tripping hazard.
− In operating or standby mode, electrical devices such as mobile phones, PCs, Televisions (LCD, plasma, tube, etc.), game
consoles etc. will emit electro-magnetic radiation. For this reason, all these types of devices should be kept away from
your training device as they could lead to malfunction, disturbances or false outputs being shown in heart rate measure-
ments.
− For safety reasons, always remove the electrical plug from the socket when the device is not in use.
Training Environment
− Select a suitable space for your training device to provide an optimum amount of free space and highest level of safety.
You should leave a safety distance of at least 100 cm behind the training device and at least 100cm to each side and in
front of the device.
− Make sure that the area is well ventilated and that an optimum amount of oxygen is available during training. Avoid
draughts.
− Your training device is not suitable for outside use and so storage and training can only take place in a temperate, clean
dry room.
− The temperature range to operate or store this device is between a minimum of 10° and maximum of 30°
− Do not operate or store your training device in wet areas such as in swimming pools, saunas etc.
− Make sure that your training device is kept on flat, hard, clean ground both in operation and at rest. Any uneven surfaces
must be removed or made good.
− It is recommended permanently to place a MAXXUS® Floor Protection Mat under the device to protect damageable floors
such as wood, laminates, floor tiles etc. Please ensure that the mat cannot slip or slide.
− Do not put this training device on pale or white coloured carpets or rugs as the feet of the device may leave marks.
− Make sure that your training device and mains cable are kept out of contact with hot surfaces and are kept at a safe dis-
tance from any sources of heat e.g. central heating, hot stoves, furnaces, ovens or open fires.
Personal Safety Instructions for Training
− Remove the mains cable from the training device when not in use to avoid inappropriate or uncontrolled use by any other
third party, e.g. children.
− You should have a health check carried out by your doctor before you start any training
− Stop training immediately if you feel physically unwell or are experiencing any breathing di翿culties.
− Always start your training session at a low workload increasing it slowly but steadily throughout. Reduce the workload
again towards the end of your training session.
− Suitable sports shoes and clothes should always be worn during training sessions. Make sure that loose clothes do not
get caught up in the treadmill belt or rollers.
− Your training device is only to be used by one person at a time.
− Check each time before a training session to see if your device is in perfect condition. Never use your training device if it is
faulty or defective.
− You are only permitted to carry out repairs to the device yourself after having contacted our Service Department and on
receipt of explicit permission to do so. Only original spare parts may be used at any time.
− Your training device must be cleaned after each use. Remove all dirt including body sweat or any other liquids.
− Always make sure that liquids (drinks, body sweat, etc.) do not get onto the vibrating plate or into the cockpit as this can
cause damage to the mechanical and electronic components.
− Your training device is not suitable for use by children.
− Third parties, especially children and animals, must be kept at an appropriate safety distance during training.
− Check if there are any items underneath the training device before each training session and remove them without fail.
Never use the training device when items are underneath it.
− Do not allow children to use your training device as a toy or climbing frame at any time.
− Ensure that no body parts of your own or of third parties ever come in contact with any of the moving mechanisms.
The construction of this training device is based on state-of-the-art technology and highest modern technical safety standards.
This training device is to be used by adults only! Extreme misuse and/or unplanned training can cause damage to your health!
This training device is suitable for non-therapeutic purposes.
4
Overview of the Device
Handlebars
Pulse sensors
Seat
Pedal
Cockpit
Tablet holder
Handlebar Shaft
Stand with Transport Rollers
Stand with
transport handle
5
Fixing Materials
Part 29
Washer Ø8
3 pieces
Part 26
Phillips screw M5x15
5 pieces
Part 19
Hexagon socket screw M10x45
4 pieces
Part 16
Hexagon socket screw M10x110
2 pieces
Part 15
Grub screw M12x70
2 pieces
Part 30
Washer Ø10
6 pieces
Part 11
Hexagon socket screw M8x20
3 pieces
Part 31
Spring washer Ø8
3 pieces
Part 20
Phillips screw M4x10
6 pieces
Part 32
Spring washer Ø10
6 pieces
Part 24
Sheet metal screw 4x16
6 pieces
Tools included in the scope of delivery
Carefully unpack all parts of the delivery. Two people are required because some parts of your training device
6
are bulky and heavy. Before starting the assembly, check the completeness of the fixing materials (screws, nuts,
etc.) and the components against the parts and fixing material lists on the previous pages of this manual.
Carefully carry out the installation, as damage or defects that have arisen due to assembly errors are not
covered by the warranty under any circumstances. Read the instructions carefully before starting, follow the
sequence of the installation steps exactly and follow the instructions for the individual assembly steps. The
installation of the training device must be carried out by responsible adults.
Carry out the installation of your training device with two adults in a location that is level, clean and free of
obstruction during assembly. Only after assembly of the training device has been completed can training be
started.
Assembly
Step 1: Mounting the front stand
Attach the front stand with transport wheels (3) to the front receptacle of the base frame (1) using two
hexagon socket screws M10x110 (16), two spring washers Ø10 (32) and two washers Ø10 (30) each.
Step 2: Mounting the rear stand
Insert the rear stand with handle into the rear receptacle of the base frame (1) and fix it with four hexagon
socket screws M10x45 (19), four spring washers Ø10 (32) and four washers Ø10 (30).
Step 3: Mounting the handlebar shaft
Slide the handlebar stem cover (52) onto the handlebar shaft(2) from below. Make sure that the covers are correctly
aligned.
Insert the M12x70 set screws (15) into the seat of the base frame (1) for the handlebar shaft and tighten them slightly so
that they grip.
Connect the cable (77) that protrudes from the bottom of the handlebar shaft (2) with the cable (78) that protrudes from
the steering shaft receptacle of the base frame (1).
Now insert the handlebar shaft (2) into the receptacle of the base frame (1). Then tighten the set screws (15) already
inserted.
Attention:
When inserting and fastening the handlebar stem (2), make absolutely sure that you do not crush or damage the cables.
Step 4: Mounting the cockpit
Connect the cockpit cable (77) sticking out of the handlebar shaft (2) with the corresponding cable (83) sticking out of the
cockpit (45 ).
Now lead the two cables of the hand pulse measurement (84) of the cockpit from above through the opening on the
handlebar shaft (2) and out again at the rear through the large opening on the handlebar shaft (2) - see also circle cut-out.
Now fix the cockpit (45) to the handlebar shaft (2) with four pan-head screws M5x15 (26).
Attention:
When inserting and attaching the cockpit (45), make absolutely sure that you do not crush or damage the cables.
7
Assembly
8
Assembly
Step 5: Mounting the handlebar
Connect the two cables of the hand pulse measurement (84) that protrude from the handlebar shaft (2) with
the cable ends (85) that protrude from the handlebar (9). The order of the connection is irrelevant as the
cables are identical.
Then fasten the handlebar (9) to the handlebar shaft (2) with three hexagon socket screws M8x20 (11),
three spring washers Ø8 (31) and three washers Ø8 (29).
Attention:
When inserting and attaching the handlebar (9), make absolutely sure that you do not crush or damage the
cables.
Step 6: Fitting the handlebar cover & water bottle holder
Insert the front and rear handlebar stem cover (57 - front/58-rear) on the handlebar stem (2) below the
cockpit and fix it to the handlebar stem (2) with one pan-head screw M5x15 (26) and two self-tapping screws
4x16 (24).
Then mount the water bottle holder (62) to the front of the handlebar stem (2) with two pan-head screws
M10x6.
9
Assembly
Step 7: Mounting the saddle
Insert the sliding rail of the saddle (69) on the rail of the saddle tube (5) and
fix it with the hand wheel (70).
Step 8: Fitting the side saddle covers
Insert the right and left saddle covers (63-left/64-right) underneath the saddle
on the saddle tube and fix them with two pan-head screws M4x10 (20) each.
Step 9: Mounting the pedals
Insert the thread of the right pedal (67) into the receptacle of the right
pedal arm and screw it clockwise.
Then insert the thread of the left pedal (66) into the receptacle of the left
pedal arm and screw it tight in an anti-clockwise direction.
For better differentiation, the right pedal is marked with an "R" and the
left pedal with an "L".
10
Assembly
Self Generator operation
Step 10: Mounting the tablet holder
Attach the tablet holder (88) to the back of the cockpit with three self-tapping screws 4x16 (24).
This training device is equipped with a generator system to produce electricity. Similar to a bicycle dynamo, the energy
generated during training is converted into electricity and used to power the cockpit and the braking system.
Switching on the cockpit
As soon as you start pedalling, the cockpit switches on automatically.
Switching off the cockpit
The cockpit switches off completely shortly after the pedalling motion has ended.
Important note regarding the operation of the generator
During operation of the generator, a steady sound similar to that of a bicycle dynamo is heard.
This is a normal operating sound of the generator and at the same time indicates its correct operation.
Otros manuales para RunMAXX 90 PRO
1
Tabla de contenidos
Otros manuales de Bicicleta estática de Maxxus
Maxxus
Maxxus SpeedBike S1 Instrucciones de instalación
Maxxus
Maxxus AirBike 90PRO Instrucciones de instalación
Maxxus
Maxxus 6.2 Instrucciones de instalación
Maxxus
Maxxus 90R Pro Instrucciones de instalación
Maxxus
Maxxus 4.2R Manual de usuario
Maxxus
Maxxus PRO SPK-21 Manual de usuario
Maxxus
Maxxus 4.2R Instrucciones de instalación
Maxxus
Maxxus SpeedBike SX3 Instrucciones de instalación
Maxxus
Maxxus PRO SPK-23 Manual de usuario
Maxxus
Maxxus 4.2 Instrucciones de instalación
