MaxxOne Kite Manual de usuario
USER
MANUAL
KITE ALARM SYSTEM
1
Table of Contents
Introducon
Important Notes for Users
About Safety
Requirements
System Status & User Authories
The Outlook
Quick Seng Up
Operang by App
FAQ
Specicaons
2
2
3
3
4
5
7
9
15
16
●
●
●
●
●
●
●
●
●
●
2
Introduction
• Thank you for purchasing the MaxxOne® Kite Smart Alarm System. Kite will give you complete control over your
home’s security and home automaon via your smartphone, tablets or web clients. This manual will guide you
through the setup procedures and highlight some key features.
• Please note that all contents listed here might be slightly dierent from the contents of the package or in App.
Please check hp://www.maxxone.com to obtain the latest version of the user manual.
Important Notes for Users
• Please connect the power cable before rst using.
• All sensors and devices in the package have already been paired with the main box before shipping. Users can start
using the whole system aer seng the network. For the extra accessories (like sensors or smart devices), you
need to pair them with the system for working normally.
• This system is designed to be easy to set and use. Most users can nish this process within 15 minutes. If there is
any problem with the seng up this device, please contact MaxxOne or the distributor for help.
• All manuals, warranty cards, nameplates and sckers with QR codes or barcodes, should be carefully kept for
future use.
3
About Safety
• This system does not oer any guarantee of protecon against burglary, robbery, the, or any type of emergency.
It is a DIY product and does not come with a tradional monitoring service. However, most of the risks have been
considered in our design to make your home safer.
• The users should connue to act prudently to protect the security of their lives and property. Any alarm system is
subject to compromise or failure for a variety of reasons as follows:
1. An intruder may gain access through unprotected openings.
2. An intruder may have the technical sophiscaon to bypass a sensor or the whole system.
3. Signals sent by the main panel or sensors may be blocked or reected before being received, and a block can
occur if metal objects are moved into the path of the signal.
4. Moon sensors can only detect the intrusion within the specied ranges and unobstructed areas.
5. Malfuncon of routers, limited services by wireless phone carriers or internet service providers, limited
service such as text messages or push nocaon provided by smartphone makers.
6. Component failures or some other errors happen in the electrical system.
Important Notes for Users
• Wired/Wireless Router compable with Wi-Fi IEEE 802.11 b/g/n standard.
• Internet Service Provider
• Mobile Telephone SIM card (only GSM/WCDMA/LTE SIM card, not CDMA one)
• iPhone(iOS v7.0 or higher ) or Android(v4.3 or higher) smartphone
4
System Status & User Authorities
• The Kite system does not support any wired sensors. The main box communicates with all sensors via wireless RF
signal protocols.
• Most of the sensors have a low-baery warning mechanism. Users will receive nocaons via the app before the
baery runs out to allow me to change them.
• The system can change its security status according to the commands given by users or the signals sent from the
triggered sensors.
Arm:
All working sensors can be
triggered. The system will
generate an alarm when
receiving the trigger signal
sent from sensors.
Disarm:
This mode will de-acvate
all sensors and will also turn
o the siren and stop the
alarm process.
Home Arm:
This mode will allow some
selected sensors to keep
working while others are
deacvated. These sensors
could be selected in App.
SOS:
SOS will trigger built-in
siren & send alarm
messages to emergency
contacts. It also triggers
external sirens or other
sensors like smart plugs.
• There are three levels of user authories:
- ADMINISTRATOR:
Who can fully control the system
and invite other users with assigned
levels.
- GUEST:
Who can only operate
ARM / DISARM / HOME ARM / SOS.
- USER:
Who can operate ARM / DISARM
/ HOME ARM / SOS and control
the smart plugs and cameras, also
can invite other people as USER or
GUEST.
5
The Outlook
• Front View • Top View
LED Indicator
5V2A Power Adapter
RJ45 100M Ethernet SIM Slot
Louvre
STATUS LED MEANING
Normal Status Light ON ARM/DISARM/HOME ARM/SOS Etc.
Seng Status Fast Blinking
Networking Congure
Reseng
Updang
Errors Slow Blinking
Low Baery
Networking Errors
Other Errors
6
• Back View
Wall Mounng Bracket
Siren Hole
Baery Cover
Networking Congure
System Reset
Power Switch
7
Quick Setting Up
- Please search My Kite in App Store or Google Play, or scan the QR code printed on the package to visit the download
page directly.
• Install the Latest App
- Please ensure the router you are using has already been connected to the Internet with DHCP mode enabled. Kite
supports IPV4 protocol only.
- The system supports the following networking type:
- LAN: 10/100M ethernet
- WiFi: 2.4GHz, WEP/WPA/WPA2 encrypted
• Prepare the Internet Networking
- If you are using WiFi connecon for the box, try your phone rst to see if it could be connect to that WiFi around the
installing locaon, to ensure the WiFi signal can be received by the main box.
• Put the Main Box to a Suitable Place
- Open the baery cover on the back, turn OFF the power switch.
- Open the SIM slot and insert the SIM card. Standard SIM card is required. If you are using the Nano-SIM or Micro-SIM,
please use card adapter to make sure it could t the slot.
- Close the SIM slot.
• Install the SIM Card (Oponal)
- Connect the power cable.
- Turn ON the power switch.
- Wait a few seconds unl the LED indicator on the front cover light up brightly.
• Power ON
8
- Hold the Networking Seng
Buon in the baery cover unl
the LED indicator starts ashing.
- Launch the App - [Start to add
a main panel] - [Quick Cong
Mode], and follow the guidelines
to nish the networking process.
• Seng Networking
- Make sure your mobile phone has been connected to the Internet via cellular or WiFi.
- Try pressing ARM/DISARM buon in App, to see if the status icon in App would be changed immediately.
- Try using remote control, pressing ARM / DISARM buon to see if the status icon in App would be changed immediately.
• Check Seng
- Put the baery cover back.
- Place your main box on the desktop or using the bracket to mount it on the wall.
• Finishing & Mounng
9
Operating by App
User Sengs
The entry for all account sengs.
- Bind Devices
- Phone/Email/Password etc.
• Introducing the Main User Interface
Real-me Status Diagram
Here shows the real-me status and
the networking connecng quality of
the system, the crucial informaon
for users.
When system status is changed, the
diagram would indicate it immediately.
To be user-friendly, the colour and
icons in the diagram are easy to
understand.
Device List
Switch between all main boxes of
current user. Add/Remove main boxes.
Shortcut Toolbar
Fixed shortcuts: Arm, Disarm.
User customised: Home Arm(default),
SOS, Smart Camera, Smart Plugs, etc.
By using shortcuts, it saves a lot of
me to operate the system.
Event List
An event is one operaon by users or
one status change by accessories.
The events would be sorted by me,
with the latest event on the top.
System & App Sengs
Access the system sengs and App
sengs.
• Manage accessories like pairing
and removing.
• Adjust some other system
parameters like Exit Delay, Entry
Delay, Duress Alarm, etc.
• Firmware update, networking
sengs and other device
advanced sengs.
Tabla de contenidos
Manuales populares de Sistema de seguridad de otras marcas
EDM
EDM Solution 6+6 Wireless-AE Manual de usuario
Highway Safety Group
Highway Safety Group EA401 Manual de usuario
Siren
Siren LED GSM Manual de usuario
Detection Systems
Detection Systems 7090i Instrucciones de montaje
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manual de usuario
Siemens
Siemens FDM273 Manual de usuario