Maxwell Digital Multimeters 25331 Manual de usuario

User ManUal

Használati Utasítás

ManUal de Utilizare

Užívateľská prírUčka

sUMMary

This broad-spectrum measurement device enables you to measure DCV, ACV, DCA,

ACA, resistance, diode and ideal for continuity test and cable test. Ideal for using in

laboratories, factories and even at home.

safety Marks

This device complies to the EN61010-1 standards.

Read the manual carefully before use.

• Do not measure a higher value than the set range.

• To avoid electric shock make sure that the measuring wires are intact.

• Disconnect the measuring wires while changing function.

• Select the proper function and range, avoid incorrect usage.

• Do not use the device if the battery holder lid and back cover are not in their

places.

• Do not measure voltage while in resistance measuring mode.

• Remove the wires and turn the device o before replacing the battery or fuse.

• Safety signs:

Dangerousvoltage

Grounding

 Doubleinsulation

 Lowbatterypower

CHaraCteristiCs

Display LCD display

Max.valuedisplay: 1999 (3 ½ digit) automatic polarity

display

Lowbatterypowerdisplay

Operatingenvironment (0-40) °C, R. H. 75%

Battery 9 V X 1 (NEDA 1604/6F22 or same

type)

Dimensions 195 X 85 X 35 mm

Weight 322 g (with battery)

teCHniCal data

V—…

Range Accuracy Resolution

200 mV ±0.8% 100 μV

2 V

±0.5%

1 mV

20 V 10 mV

200 V 100 mV

600 V ±1% 1 V

Input impedance: 10 MΩ

Overvoltage protection: 600 V (DC/AC RMS)

Range Accuracy Resolution

2 V

±1.2%

1 mV

20 V 10 mV

200 V 100 mV

600 V 1 V

Input impedance: 10 MΩ

Overvoltage protection: 600 V (DC/AC RMS)

A—…

Range Accuracy Resolution

20 mA

±0.8%

10 μA

200 mA 100 μA

10 A ±1.5% 10 mA

Max. inward current 10 A (testing time should be 10 sec max.)

Fuse 0,5 A/250 V and 10 A / 250 V fast fuse

Range Accuracy Resolution

200 mA ±1% 100 μA

10 A ±1.5% 10 mA

Max. inward current 10 A (testing time should be 10 sec max.)

Fuse 0,5 A/250 V and 10 A / 250 V fast fuse

Frequency range 40 Hz - 400 Hz

Resistance

Range Accuracy Resolution

200 Ω

±1.5%

0.1 Ω

2 kΩ 1 Ω

20 kΩ 10 Ω

200 kΩ 100 Ω

2 MΩ 1 kΩ

20 MΩ 10 kΩ

Overvoltage protection: 250 V (DC/AC RMS)

Warning:DoNOTmeasurevoltageinresistancemode!

Diodeandcontinuitytest

Function Description Teststate

Measures the

opening voltage of

the diode

The opening DC amperage is

approx. 1 mA, the closing voltage is

approx. 2,7 V

Beeping sound

if the resistance

is lower than

(30±20)Ω

Open circuit voltage: 1.5V

Overvoltage protection: 250 V (DC/AC RMS)

Functionchart

Chart of LEDs response during the tests of dierent wires.

MODE 1 2 3 4 5 6 7 8 G

RJ45 ✓✓✓✓✓✓✓✓✓

RJ12 ✓ ✓ ✓ ✓ ✓ ✓

RJ11 ✓✓✓✓

USB ✓ ✓ ✓ ✓ ✓

OperatiOn

1. RJ45, RJ11, RJ12, USB test connector

2. Display

3. „Test” button

4. Function switching switch

5. „10A”socket: 200mA - 10A

6. ”mA” socket: til 200mA

7. USB test socket (removable)

8. Cable test LED lighting

9. ”Hold” button

10.”Light” (background lighting) button

11.”V-Ω” socket

12.”COM”(common) socket

13.Cable testing LED line

14.Test socket RJ45, RJ11, RJ12 (removable)



V—… measuring

• Connect the black measurning wire to the „COM” socket and the red one to

the„V/Ω”socket.

• Set the function switch to the proper „V—…

setting and connect the wires to the circuit.

Note:

• Ifyouare unsureabout the measuredvoltage range, set thefunction

switchtoahigherrange.

• IftheLCDshows„1”,itmeansareallyhighvalue,andtherangeshould

besettoahighervalue.

V~measuring

• Connect the black measurning wire to the „COM” socket and the red one to

the„V/Ω” socket.

• Set the function switch to the proper "V~ "

measuring setting and connect the wires to the circuit.Note:

• Ifyouare unsureabout the measuredvoltage range, set thefunction

switchtoahigherrange.

• IftheLCDshows„1”,itmeansareallyhighvalue,andtherangeshould

besettoahighervalue.

A—… measuring

• Connect the black measurning wire to the „COM” socket and the red one to

the „mA” socket (max. 200 mA) or connect the red one to the „10A” socket

(max. 10 A).

• Set the function switch to the proper „A—…

setting and connect the wires to the circuit.

Note:

• Ifyouareunsureaboutthemeasuredamperagerange,setthefunction

switchtoahigherrange.

• IftheLCDshows„1”,itmeansareallyhighvalue,andtherangeshould

besettoahighervalue.

• Max. input amperage 200 mA or 10 A (depends on where the red

measuring wire is connected to), in case of high amperage the fuse

melts.

A~measuring

• Connect the black measurning wire to the „COM” socket and the red one to

the „mA” socket (max. 200 mA) or connect the red one to the „10A” socket

(max. 10 A).

• Set the function switch to the proper „A~" setting and connect the wires to the

circuit.

Note:

• Ifyouareunsureaboutthemeasuredamperagerange,setthefunction

switchtoahigherrange

• IftheLCDshows„1”,itmeansareallyhighvalue,andtherangeshould

besettoahighervalue.

• Max. input amperage 200 mA or 10 A (depends on where the red

measuring wire is connected to), in case of high amperage the fuse

melts.

Resistancemeasurement

• Connect the black measurning wire to the „COM” socket and the red one to

the„V/Ω" socket.

• Set the function switch to the proper resistance setting and connect the wires

to the resistance you wish to measure.

Note:

• If the value of the measured resistance is higher than the choosen

maximumvalue,theLCDshows„1”,andthefunctionswitchhastosetto

ahighersettingvalue.Iftheresistanceisabove1MΩ,thedeviceneeds

somesecondstostabilise.

Diodeandcontinuitytest

• Connect the black measurning wire to the„COM”socket and the red one to the

„V/Ω" socket. (Note: the polarity of the red wire:„+”)

• Set the function switch to „ ”setting and connect the wires to the diode

you wish to measure

• Connect the wires to the 2 points of the part, if the device beeps the resistance

is lower than approx. (30±20)Ω

Backgroundlighting

• Push the button '10' long to turn on or o the background lighting.

Datahold

• By pushing the push button„HOLD”, the measured value stays on the display.

To turn this function o, push the button„HOLD” again.

Cabletestfunction

• The cable test function can be used to continuity test of ethernet- (UTP, FTP),

phone- and USB wires, in automatic and manual mode, as well.

• Connect one end of the wire, you wish to test, to the proper connector of the

connectors marked with “1”and the other end to the socket„7”or„14”.

Manualtesting

• Set the device into „MANUAL” setting and by pushing the button „TEST”, the

testing starts.

• At each pushing the following lead will be tested.

• By pushing the button continuously, the device tests the leads automatically

until the button is pushed.

Automatictesting

• Set the device into “AUTO” setting and by pushing the button „TEST”, the

testing starts.

• The device tests the leads automatically one by one.

Errorsignal

• Disconnection – if one or more wires are diconnected, the LEDs with same

number do not light on the main unit and on the removable control unit

• Short circuit – If more wires are short-circuited, more LEDs light on the main

unit and on the removable control unit at the same time.

MaintenanCe

• Note that the device is not water-, dust- and shock- resistant.

• Do not use and do not store the device at high temperatures, in places with

high humidity or ammability or in strong magnetic elds.

• Do not use rough textile or alcohol to clean the device.

• If the device is not being used for a longer time period, the battery must be

taken out.

Batteryreplacement(1piece9Vbattery)

If the LCD display shows „ ” the battery needs to be replaced the following

way:

• Take the device out of the plastic holder and take o the battery holder cover.

• Take out the battery and replace it to a new one. Use alkaline batteries if

possible.

• Fix the battery holder cover and put the plastic holder back.

Fusereplacement

• Only use the prescribed types of fuses for replacing.

If the device does not operate properly, check the following

State Solution

Nothing is displayed • Device is turned o

• Replace the battery

„ ”is displayed Replace the battery

No power Replace the fuse

Összegzés

A műszer széleskörű használata lehetővé teszi DCV, ACV, DCA, ACA, ellenállás,

dióda mérését, valamint folytonossági- és kábelteszt végzésére is alkalmas.

Használata ideális laboratóriumokban, gyárakban és otthon is.

BiztOnsági Megjegyzés

A mérőműszer az EN61010-1 szabványoknak megfelel. Használat előtt gyelme-

sen olvassa el a használati utasítást.

• Ne mérjen nagyobb értéket a beállított méréshatárnál.

• Az elektromos áramütés elkerülése miatt ellenőrizze, hogy a műszerzsinórok

sérülés mentesek legyenek.

• Ügyeljen rá, hogy funkcióváltáskor a műszerzsinórok a megfelelő aljzatba

legyenek bedugva.

• Válassza ki a helyes funkciót és méréshatárt, kerülje el a hibás műveleteket.

• Ne használja a mérőműszert, ha az elemtartó fedele és a hátlapja nincs a

helyére rögzítve.

• Ellenállásmérés állásban ne mérjen feszültséget.

• Húzza ki a vezetékeket és kapcsolja ki a műszert, mielőtt kicseréli az elemet

vagy a biztosítékot.

• Biztonsági jelzések:

Fennálóveszélyesfeszültség

Föld

 Duplaszigetelés

 Gyengeakkumulátor

jelleMzők

Kijelző LCD kijelzés

Max.kijelzés: 1999 (3 ½ digites) automatikus polaritás

kijelzéssel

Gyengeakkumulátor

kijelzés

Működésikörnyezet (0-40) °C, R. H. 75%

Elem 9 V X 1 (NEDA 1604/6F22 vagy ugyanolyan

típusú)

Méret 195 X 85 X 35 mm

Tömeg 322 g (elemmel)

Tabla de contenidos

Idiomas:

Otros manuales de Multímetro de Maxwell Digital Multimeters

Maxwell Digital Multimeters

Maxwell Digital Multimeters 25108 Manual de usuario

Maxwell Digital Multimeters

Maxwell Digital Multimeters 25404 Manual de usuario

Maxwell Digital Multimeters

Maxwell Digital Multimeters 25 313 Manual de usuario

Maxwell Digital Multimeters

Maxwell Digital Multimeters MX 25 312 Manual de usuario

Maxwell Digital Multimeters

Maxwell Digital Multimeters MX 25 314 Manual de usuario

Maxwell Digital Multimeters

Maxwell Digital Multimeters 25520 Manual de usuario

Maxwell Digital Multimeters

Maxwell Digital Multimeters 25334 Manual de usuario

Maxwell Digital Multimeters

Maxwell Digital Multimeters 25521A Manual de usuario

Maxwell Digital Multimeters

Maxwell Digital Multimeters 25404 Manual de usuario

Maxwell Digital Multimeters

Maxwell Digital Multimeters 25109 Manual de usuario

Maxwell Digital Multimeters

Maxwell Digital Multimeters 25103 Manual de usuario

Maxwell Digital Multimeters

Maxwell Digital Multimeters 25306 Manual de usuario

Maxwell Digital Multimeters

Maxwell Digital Multimeters 25221 Manual de usuario

Maxwell Digital Multimeters

Maxwell Digital Multimeters 25506 Manual de usuario

Maxwell Digital Multimeters

Maxwell Digital Multimeters 25211 Manual de usuario

Maxwell Digital Multimeters

Maxwell Digital Multimeters 25 702 Manual de usuario

Maxwell Digital Multimeters

Maxwell Digital Multimeters 25 222 Manual de usuario

Maxwell Digital Multimeters

Maxwell Digital Multimeters 25303 Manual de usuario

Maxwell Digital Multimeters

Maxwell Digital Multimeters 25210 Manual de usuario

Maxwell Digital Multimeters

Maxwell Digital Multimeters 25624 Manual de usuario

Maxwell Digital Multimeters

Maxwell Digital Multimeters 25221 Manual de usuario

Maxwell Digital Multimeters

Maxwell Digital Multimeters 25302 Manual de usuario

Maxwell Digital Multimeters

Maxwell Digital Multimeters 25402 Manual de usuario

Maxwell Digital Multimeters

Maxwell Digital Multimeters MX 25 318 Manual de usuario

Manuales populares de Multímetro de otras marcas

Agilent Technologies

Agilent Technologies 34420A Manual de usuario

Fluke

Fluke 83 Manual de usuario

Hameg

Hameg HM 8012 Manual de usuario

Mastech

Mastech MY70 Manual de usuario

Steren

Steren MUL-300 Manual de usuario

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Manual de usuario

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Manual de usuario

PeakTech

PeakTech 4000 Manual de uso y cuidado

YOKOGAWA

YOKOGAWA 90050B Manual de usuario

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Manual de usuario

Fluke

Fluke 8846A Manual de operación y mantenimiento

Tempo Communications

Tempo Communications MM200 Manual de usuario

Elenco Electronics

Elenco Electronics CM-1555 Manual de usuario

Mastech

Mastech MS8238C Manual de usuario

SDAR

SDAR 830A, 830B, 830D, 830C Manual de usuario

RS PRO

RS PRO RS-9519BT Manual de usuario

BGS technic

BGS technic 8890 Manual de usuario

Amprobe

Amprobe Hexagon 60 Manual de usuario