Maxtec R219P86 Manual de usuario

ACRYLIC FLOW METERS

ASSEMBLY INSTRUCTIONS &

INSTRUCTIONS FOR USE

R219P86 (0-120LPM)

R219P87 (0-70LPM)

R219P88 (0-30 LPM)

R138P11 Rev. E

0-30, 0-70 & 0-120 LPM

III

866.4.Maxtec www.maxtec.com

TABLE OF CONTENTS

1.0 PRODUCT OVERVIEW .....................................................1

1.1 Description ......................................................................... 1

1.2 Indications For Use............................................................... 1

1.3 Warnings ............................................................................ 1

1.4 Cautions .......................................................................... 1-2

2.0 PRODUCT SPECIFICATIONS............................................. 3

2.1 Flow Ranges, Graduations & Accuracy.................................... 3

2.2 Transport/Storage Requirements .......................................... 3

3.0 OPERATING INSTRUCTIONS ............................................ 4

3.1 General Operation............................................................... 4

4.0 TROUBLESHOOTING .................................................... 5

4.1 Troubleshooting Table: ........................................................ 5

5.0 RECOMMENDED MAINTENANCE ...................................... 5

5.1 Cleaning Instructions ........................................................... 5

6.0 WARRANTY ................................................................ 6

7.0 SYMBOL GUIDE ............................................................ 7

866.4.Maxtec www.maxtec.com

1.0 PRODUCT OVERVIEW

1.1 Description

The ﬂow meter is intended for use by physicians, respiratory therapists

and other authorized hospital personnal to administer selected doses of

medical gases to a patient.

1.2 Indications for use

This manual instructs a professional to install and operate the ﬂow meter.

This is provided for your safety and to prevent damage to the ﬂow meter.

If you do not understand this manual, DO NOT USE the ﬂow meter and

contact your provider.

1.3 Warnings

• Use ﬂow meters only for their “Intended Use” as described in this

manual.

• ALWAYS conﬁrm prescribed ﬂow before administering to patient and

monitor ﬂow on a frequent basis.

• Flow meters may contain magnetic, ferrous material that may aect

the results of an MRI.

• Read this User Manual before installing or operating the ﬂow meter.

To Reduce the Risk of Fire or Explosion:

• ALWAYS follow ANSI and CGA standards for Medical Gas Products

and ﬂow meters and Oxygen Handling.

• DO NOT use or store oils, greases, organic lubricants or any

combustible materials on or near this Flow meter.

• DO NOT use near any type of ﬂame or ﬂammable/explosive

substances, vapors or atmosphere.

• DO NOT connect to source pressure greater than 100 psi.

• DO NOT smoke in an area where oxygen is being administered.

1.4 Cautions

• Use caution to avoid cross-threading ﬁttings during installation.

• Always use a backing wrench when installing or removing connectors.

866.4.Maxtec www.maxtec.com

• Flow meters must be operated with the Flow Tube in a vertical,

upright position.

• Only personnel instructed and trained in its use should operate this

ﬂow meter.

• Ensure all connections are tight and leak free.

• Only use oxygen-safe leak detector.

• Only trained medical professionals should operate the ﬂow meter.

• DO NOT drop the ﬂow meter.

• DO NOT autoclave.

• DO NOT gas sterilize with EtO (Ethylene Oxide).

• DO NOT clean with aromatic hydrocarbons.

• DO NOT immerse ﬂow meter in any kind of liquid. This will void the

warranty.

• DO NOT USE if damaged. Inspect the ﬂow meter for visual damage

before use.

• DO NOT over-tighten knob when turning o. This will cause damage

to the ﬂow meter.

• DO NOT over-tighten any threaded connectors; body may crack and

cause leaks.

• Pressures other than those indicated on the ﬂow tube or ﬂow meter

body may aect the accuracy of the indicated ﬂow.

• Gas Temperatures other than 70° F (21°C) may aect the accuracy of

the indicated ﬂow.

• Attaching accessories to the outlet (which may increase resistance

to outlet ﬂow) may change indicated ﬂow but will not aect the

accuracy of the ﬂow.

• ONLY use appropriate gas speciﬁc indexed ﬁttings to connect ﬂow

meter to gas source. Use Oxygen connections for oxygen ﬂow

meters; use air connections for air ﬂow meters.

866.4.Maxtec www.maxtec.com

2.0 SPECIFICATIONS

2.1 Flow Range Accuracy Chart

FLOW RANGE GRADUATIONS ACCURACY

0-30 LPM 1 (0-30) LPM

2-4: ± .50 l/min,

5-30: ± 10% of

indicated value

0-70 LPM 5 (0-70) LPM ± 10% of indicated value

0-120 LPM 10 (0-120) LPM ± 10% of indicated value

For the most current manual revision please visit our website:

www.maxtec.com

Flush Flow is the output of the ﬂow meter when the ﬂow indicator is

beyond the highest calibrated graduation. The Flush Flow range is as

indicated on the ﬂow meter labeling.

2.2 Transport/Storage Requirements

-40 °F (-40 °C) to 140 °F (60 °C)

The gas and inlet pressures are indicated on the ﬂow tube or ﬂow

meter body.

NOTE: Storage/transport outside the speciﬁed range may cause damage

to the ﬂow meter.

The above ﬂow meter models are calibrated at speciﬁed inlet pressure,

70°F (21°C), standard atmospheric pressure. Speciﬁcations are subject to

change without prior notice.

866.4.Maxtec www.maxtec.com

3.0 OPERATING INSTRUCTIONS

3.1 General Operation

NOTE: Maxtec strongly recommends the use of kink proof cannula.

1. Turn knob to the “OFF” position.

2. Connect the ﬂow meter vertically to the appropriate gas source. The

appropriate gas and pressure are speciﬁed on the ﬂow meter body.

3. Verify that the ﬂoat ball is at the very bottom of the ﬂow tube.

NOTE: If the ﬂoat is not resting at the bottom of the ﬂow tube, the

product is leaking; consult the “TROUBLESHOOTING” Section 4.0.

4. Adjust ﬂow:

To increase- Turn knob counterclockwise

To decrease- Turn knob clockwise

5. Set ﬂow by aligning center of ﬂoat ball with indicator lines on the

ﬂow tube.

6. Adjusting ﬂow beyond the last calibrated indicator line will result in

an undetermined ﬂow.

7. To obtain maximum ﬂush ﬂow, turn knob fully counterclockwise.

NOTE: Flush ﬂow is any ﬂow above the last calibrated line on the ﬂow

tube with an unrestricted ﬂow, as indicated on ﬂow meter labeling.

866.4.Maxtec www.maxtec.com

4.0 TROUBLESHOOTING

4.1 Troubleshooting Table

If the ﬂow meter fails to function, consult your provider or Maxtec.

PROBLEM CAUSE REMEDY

Will not shut o • Leak

• Defective

valve

• Replace seals

and/or ﬁttings

• Replace valve

Sticking ﬂoat ball • Debris in

ﬂow tube

• Clean ﬂow tube

& ﬂoat ball

Unable to set

desired ﬂow

• Blocked inlet • Replace ﬁlter

Knob will not turn • Valve seized • Replace valve

5.0 RECOMMENDED MAINTENANCE

5.1 Cleaning Instructions

1. Disconnect all connections before cleaning.

2. Clean exterior surfaces of the ﬂow meter with a cloth dampened with

a mild detergent and water.

3. Wipe dry with a clean cloth.

Caution: Do Not Autoclave

866.4.Maxtec www.maxtec.com

6.0 WARRANTY

Under normal operating conditions, Maxtec warrants the Acrylic Flow

Meters to be free from defects of workmanship or materials for the

following period:

a) Acrylic Housing....................................... Lifetime of the product

b) Needle Valve ......................................Five (5) years from receipt

c) All other parts not listed .......................Two (2) years from receipt

Warranty does not cover breakage/abuse.

These warranties are from the date of receipt, provided that the

product is properly operated and maintained in accordance with

Maxtec's operating instructions. Based on Maxtec product evaluation,

Maxtec's sole obligation under foregoing warranty is limited to making

replacements, repairs, or issuing credit for equipment found to be

defective. This warranty extends only to the buyer purchasing the

equipment directly from Maxtec or through Maxtec's designated

distributors and agents as new equipment. Routine maintenance

items, such as o-rings, are excluded from warranty. Maxtec and any

other subsidiaries shall not be liable to the purchaser or other persons

for incidental or consequential damages or equipment that has been

subject to abuse, misues, mis-application, alteration, negligence or

accident.

These warranties are exclusive and in lieu of all other warranties,

expressed or implied, including warranty of merchantability and ﬁtness

for a particular purpose.

For product warranty returns, please contact Maxtec

Customer Service for a Returned Materials Authorization

(RMA).

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Maxtec

Maxtec

Maxtec MaxO2 ME+p Manual de usuario

Maxtec

Maxtec R217P65 Manual de usuario

Maxtec

Maxtec RES7002 Manual de usuario

Maxtec

Maxtec R217P65 Manual de usuario

Maxtec

Maxtec MaxBlend 2 Manual de usuario

Maxtec

Maxtec Handi+ Manual de usuario

Maxtec

Maxtec R219P99-400 Manual de usuario

Maxtec

Maxtec Handi+ R218P12 Manual de usuario

Maxtec

Maxtec Handi+ Manual de usuario

Maxtec

Maxtec Handi+N2 Manual de usuario

Maxtec

Maxtec MaxVenturi Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario