Maxi-matic EPB-1800 Manual de usuario

LIMITED WARRANTY* ONE (1) YEAR:

Your small kitchen appliance is warranted to the original purchaser to be free from any manufacturing

defects under normal use and conditions for one (1) year, cord excluded. During that period, should the

appliance fail to operate properly, return the appliance with your sales receipt to the store where

purchased. If you use your appliance for household use and according to instructions, it should give

you years of satisfactory service. This product warranty covers only the original consumer purchaser

of the product.

WARRANTY IS ONLY VALID WITH A DATED PROOF OF PURCHASE.

To guarantee repair or replace without charge, a dated sales receipt showing purchase within the

limited warranty period* must accompany the appliance. Without a sales receipt, warranty will be

estimated according to the appliance's manufactured date. A comparable appliance should arrive

within 2-3 weeks. However, in case an appliance is not covered by warranty, correspondence offering

alternatives will be mailed to you.

During the one-year warranty period, a product with a defect will be either repaired or replaced with a

reconditioned comparable model (at our option) when the product is returned to our Service Center.

(See the “Returns” section below). The repaired or replacement product will be in warranty for the

remaining balance of the one-year warranty period and an additional one-month period.

This limited warranty covers appliances purchased and used within the 50 contiguous states

plus the District of Columbia and does NOT cover:

- Damages caused by unreasonable use, neglect, normal wear and tear, commercial use, improper

assembly or installation of product.

- Damages caused in shipping.

- Damages caused by replacement or resetting of house fuses or circuit breakers.

- Defects other than manufacturing defects.

- Breakage caused by misuse, abuse, accident, alteration, lack of proper care and maintenance, or

incorrect current or voltage.

- Lost or missing parts of the product. Parts will need to be purchased separately.

- Damages of parts that are not electrical; for example: cracked or broken plastic or glass.

- Damage from service or repair by unauthorized personnel.

- Extended warranties purchased via a separate company or reseller.

- Consumer’s remorse is not an acceptable reason to return a product to our Service Center.

*The consumer is responsible for any delivery charges for all replacement units provided for exchange

under the warranty.

RETURNS: Any return of defective merchandise to the manufacturer must be processed accordingly

by contacting customer service first to obtain an RA # (Return Authorization Number). We will not

accept any returns of merchandise without an applicable RA #.

We cannot assume responsibility for loss or damages to products returned to us during incoming

shipment. For your protection, always carefully package the product for shipment and insure it with the

carrier. Be sure to enclose the following items with your return: any accessories related to the

problem, your full address and daytime phone number, a note describing the problem, a copy of the

dated sales receipt or other proof of purchase and a valid RA#.

C.O.D shipments cannot be accepted.

*One Year LimitedWarranty valid only in the 50 contiguous states plus the District of Columbia,

excluding Puerto Rico and the Virgin Islands.

This warranty is effective only if the product is purchased and operated in the USA; product usage

which is in violation of the written instructions provided with the unit will void this warranty.

For international warranty, please contact the local distributor.

**Any instruction or policy included in this manual may be subject to change at any time.

Model EPB-1800 Elite Cuisine®17pc Personal Drink Blender

Distributed by: MAXI-MATIC®, USA

18401 E. Arenth Ave. Building B. City of Industry, CA 91748

Customer Service Department: (626) 912-9877 Ext. 120 MON-FRI 9am-5pm PST

Email: info@maxi-matic.com

17PC Personal Drink Blender

Model EPB-1800

Instruction Manual

IMPORTANT SAFEGUARDS

Always follow basic safety precautions when using electrical products,

especially when children are present.

WARNING: To avoid the risk of electrical shock, always make sure the product is

unplugged from the electrical outlet before assembling, disassembling, relocating,

servicing, or cleaning it.

READ ALL INSTRUCTIONS BEFORE USING

WARNING-- To reduce the risk of fire, electrical shock, or serious

personal injury:

This product is intended for use in processing foods for human consumption. Do

not use the product for any other purpose.

Do not leave the product unattended while in use. Always unplug the product

from the electrical outlet when not in use.

Keep the Power Cord and product away from heated surfaces.

Do not place product base in or expose it to water or other liquids.

Do not use attachments not recommended or sold by the product manufacturer.

Handle the Blade assembly with care as the blades are extremely sharp. Use

caution when attaching or detaching the Blade assembly.

Do not touch moving parts (e.g., the Blades) while the product is in use. Keep

hands and utensils away from the moving blade assembly while operating the

product.

Before disassembling the product, unplug it from the electrical outlet and ensure

the Blades have completely stopped.

Do not plug or unplug the product into/from the electrical outlet with a wet hand.

To disconnect from an electrical outlet, pull directly on the plug; do not pull on the

Power Cord.

Unplug the product from the electrical outlet prior to putting on or removing parts.

Never operate this product if it has a damaged Power Cord or plug, is not

working properly, has been dropped or damaged, or if the Base has been

exposed to water or other liquids. Do not attempt to examine or repair this

product yourself. Only qualified service personnel should perform servicing.

Take the product to an appliance repair shop of your choice for inspection and

repair.

CAUTION-- To reduce the risk of personal injury or product damage:

Do not allow the Power Cord to hang (e.g., over the edge of a table or counter)

where it may be tripped over or pulled.

Always place the product on a flat, level, stable surface.

Keep the product out of the reach of children and pets. This product is not

intended for use by children.

This product is intended for indoor, non-commercial, non-industrial, household

use only. Do not use outdoors.



SPECIAL INSTRUCTION:

a) To avoid a circuit overload when using this product, do not operate another high-

wattage product on the same electrical circuit.

b) If an extension cord is used with this product, a 10-amp extension cord should be

used. Extension cords rated for less amperage may overheat. The marked electrical

rating of the cord set or extension cord should be at least as great as the electrical

rating of the product.

WARNING: This product is equipped with a polarized plug (one blade is wider than

the other blade) as a safety feature to reduce the risk of electrical shock. This plug

will fit into a polarized outlet only one way. This is a safety feature. If you are unable

to insert the plug into the electrical outlet, try reversing the plug. If the plug still does

not fit, contact a qualified electrician. Never use the plug with an extension cord

unless the plug can be fully inserted into the extension cord. Do not alter the plug. Do

not attempt to defeat the safety purpose of the polarized plug.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

Parts

A. Power Switch

B. Base (1)

C. Power Cord

D. Cross Blade assembly (1)

E. Drinking Cap

F. Removable Spill-proof Lids (4)

G. Foam Grips (4)

H. Grinder Cup (1)

I. Mixing Cup (4)

J. Flat Blade assembly (1)

To Assemble

NOTE: Before using the product for the first time, disassemble and thoroughly wash

and dry all accessories except the main Base such as the cups, blade assembly and

spill-proof lids).

WARNING: Ensure the product is unplugged from the electrical outlet before

assembling it. Handle the Blade assembly with care as the blades are extremely

sharp. Use caution when attaching, detaching, cleaning, or storing the Blade

assembly.

CHOPPING & BLENDING

1. Ensure the product is unplugged from the electrical outlet.

2. Place the Base on a flat, level, stable surface.

3. Fill the Small Cup or the Large Cup with the food that you wish to chop/blend.

4. Screw the Flat Blade assembly or Cross Blade assembly clockwise onto the

Small or Large Cup until secure.

NOTE: Ensure that the rubber gasket, located on the inside bottom edge of the

blade assembly, is in place. This will prevent leaking.

5. Turn the Chopper Cup Assembly upside down so that the Blade assembly is on

the bottom. Attach the assembled Chopper by aligning the three tabs on the

outside of the Small or Large Cup with the three notches on the top inner edge of

the Base.

6. Plug the product into a standard 120-volt AC electrical outlet.

7. Each Cup Assembly has three small tabs which fit into three grooves on the top

lip of the Base. Press down on the Cup Assembly firmly and turn it counter-

clockwise to lock into place. Press and hold the Power Pulse switch to operate.

To prevent product overheating, limit continuous operation to five seconds at a

time. NOTE: The Cup Assembly must be locked in order to operate.

8. To stop processing, simply let go of the Power Pulse switch. Wait until the

Blades stop completely before removing the Cup Assembly by turning it clock-

wise to unlock it from the Base.

9. Unplug the product from the electrical outlet when it is not in use or is left

unattended.

USING DRINKING CUPS:

1. Ensure the product is unplugged from the electrical outlet.

2. Place the Base on a flat, level, stable surface.

3. Add the ingredients that you wish to include in your drink into one of the Drinking

Cups. If attached, remove the spill-proof lids before installing blade assembly.

4. Screw the Cross Blade assembly onto the Drinking cup.

5. Turn the Drinking cup so that the Blade assembly is on the bottom. Attach the

assembled Drinking cup by aligning the three tabs on the sides of the Drinking

cup with the three notches on the top inner edge of the Base.