Max SuperRoofer CN445R2 Instrucciones de funcionamiento

OPERATING AND MAINTENANCE MANUAL

MANUEL D'UTILISATION ET D'ENTRETIEN

MANUAL DE OPERACIONES Y MANTENIMIENTO

CN445R2

PNEUMATIC ROOFING COIL NAILER

DISPOSITIVO NEUMÁTICO DE CLAVETEADO

DE BOBINA DE TEJADO

CLOUEUR A BOBINE DE TOITURE PNEUMA-

TIQUE

BEFORE USING THIS TOOL, STUDY THIS MANUAL TO ENSURE SAFETY WARNING AND IN-

STRUCTIONS.

KEEP THESE INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE.

AVANT D’UTILISER CET OUTIL, LIRE CE MANUEL ET LES CONSIGNES DE SÉCURITÉ AFIN DE

GARANTIR UN FONCTIONNEMENT SÛR.

CONSERVER CE MANUEL EN LIEU SÛR AVEC L’OUTIL AFIN DE POUVOIR LE CONSULTER UL-

TÉRIEUREMENT.

ANTES DE UTILIZAR ESTA HERRAMIENTA, LEA DETENIDAMENTE ESTE MANUAL PARA FAMILIARIZARSE CON

LAS ADVERTENCIAS E INSTRUCCIONES DE SEGURIDAD.

CONSERVE ESTAS INSTRUCCIONES JUNTO CON LA HERRAMIENTA PARA FUTURAS CONSULTAS.

WARNING

AVERTISSEMENT

ADVERTENCIA

INDEX INDEX ÍNDICE

ENGLISH Page 3 to 12

FRANÇAIS Page 13 to 22

ESPAÑOL Page 23 to 32

DEFINITIONS OF SIGNAL WORDS

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in

death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in mi-

nor or moderate injury.

NOTE: Emphasizes essential information.

DÉFINITIONS DES DIFFÉRENTS DEGRÉS D’ AVERTISSEMENTS

AVERTISSEMENT: Indique une situation éventuellement dangereuse qui, si elle n’est pas

contournée, pourrait provoquer la mort ou des blessure sérieuses.

ATTENTION:

Indique une situation éventuellement dangereuse qui, si elle n’est pas contournée,

pourrait provoquer des blessures légères à moyennement sérieuses.

REMARQUE: Souligne des informations importantes.

DEFINICIÓN DE LAS INDICACIONES DE ADVERTENCIA

ADVERTENCIA: Indica una situación potencialmente peligrosa que podría causar la muerte o

graves lesiones si no se evita.

PRECAUCIÓN: Indica una situación potencialmente peligrosa que podría causar lesiones menos

graves o leves si no se evita.

NOTA: Resalta informaciones importantes.

INDEX

1. GENERAL SAFETY WARNINGS........................................................3

2. SAFETY WARNING .............................................................................4

3. SPECIFICATIONS AND TECHNICAL DATA ......................................7

4. AIR SUPPLY AND CONNECTIONS....................................................7

5. INSTRUCTIONS FOR OPERATION....................................................8

6. MAINTAIN FOR PERFORMANCE ....................................................12

7. STORING ...........................................................................................12

8. TROUBLE SHOOTING/REPAIRS .....................................................12

1. GENERAL SAFETY WARNINGS 1. WEAR SAFETY GLASSES OR GOGGLES

Danger to the eyes always exists due to the possibility of

dust being blown up by the exhausted air or of a fastener fly-

ing up due to the improper handling of the tool. For these

reasons, safety glasses or goggles shall always be worn

when operating the tool.

The employer and/or user must ensure that proper eye pro-

tection is worn. Eye protection equipment must conform to

the requirements of the American National Standards Insti-

tute, ANSI Z87.1 (Council Directive 89/686/EEC of 21 DEC.

1989) and provide both frontal and side protection.

The employer is responsible to enforce the use of eye pro-

tection equipment by the tool operator and all other person-

nel in the work area.

NOTE: Non-side shielded spectacles and face shields

alone do not provide adequate protection.

2. EAR PROTECTION MAY BE REQUIRED IN SOME ENVI-

RONMENTS

As the working condition may include exposure to high noise

levels which can lead to hearing damage, the employer and

user should ensure that any necessary hearing protection is

provided and used by the operator and others in the work area.

ENGLISH

OPERATING AND MAINTENANCE MANUAL

BEFORE USING THIS COMPRESSOR, STUDY THIS MANUAL TO ENSURE SAFETY WARNING

AND INSTRUCTIONS.

KEEP THESE INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE.

WARNING

READ ALL SAFETY WARNINGS AND ALL

INSTRUCTIONS.

Failure to follow the warnings and instructions

may result in death serious injury.

Save all warn-

ings and instructions for future reference.

WARNING

3. KEEP HANDS AND BODY AWAY FROM THE DIS-

CHARGE OUTLET

When loading and using the tool, never place a hand or any

part of body in fastener discharge area of the tool. It is very

dangerous to hit the hands or body by mistake.

4. DO NOT USE ON SCAFFOLDINGS AND LADDERS

Do not use on scaffoldings and ladders with fastener driving

tools equipped with contact actuation or continuous contact

actuation.

2. SAFETY WARNING

1. DO NOT USE ANY POWER SOURCE EXCEPT AN AIR

COMPRESSOR

The tool is designed to operate on compressed air. Do not

operate the tool on any other highpressure gas, combusti-

ble gases (e.g., oxygen, acetylene, etc.) since there is the

danger of an explosion. For this reason, absolutely do not

use anything other than an air compressor to operate the

tool.

2. OPERATE WITHIN THE PROPER AIR PRESSURE

RANGE

The tool is designed to operate within an air pressure range

of 70 to 100 p.s.i. (5 to 7 bar).

The pressure should be adjusted to the type of the work be-

ing fastened. The tool shall never be operated when the op-

erating pressure exceeds 120 p.s.i. (8.3 bar).

Never connect the tool to air pressure which potentially ex-

ceeds 200 p.s.i. (13.8 bar) as the tool can burst.

3. DO NOT OPERATE THE TOOL NEAR A FLAMMABLE

SUBSTANCE

Never operate the tool near a flammable substance (e.g.,

thinner, gasoline, etc.). Volatile fumes from these substanc-

es could be drawn into the compressor and compressed to-

gether with the air and this could result in an explosion.

4. NEVER USE THE TOOL IN AN EXPLOSIVE ATMOS-

PHERE

Sparks from the tool may ignite atmospheric gases, dust or

other combustible materials.

5. DO NOT USE A WRONG FITTINGS

The connector on the tool must not hold pressure when air

supply is disconnected. If a wrong fitting is used, the tool

can remain charged with air after disconnecting and thus

will be able to drive a fastener even after the air line is dis-

connected, possibly causing injury.

6. DISCONNECT THE AIR SUPPLY AND EMPTY THE

MAGAZINE WHEN THE TOOL IS NOT IN USE

Always disconnect the air supply from the tool and empty

the magazine when operation has been completed or sus-

pended, when unattended, moving to a different work area,

adjusting, disassembling, or repairing the tool, and when

clearing a jammed fastener.

7. INSPECT SCREW TIGHTNESS

Loose or improperly installed screws or bolts cause acci-

dents and tool damage when the tool is put into operation.

Inspect to confirm that all screws and bolts are tight and

properly installed prior to operating the tool.

Thinner Gasoline

8. DO NOT TOUCH THE TRIGGER UNLESS YOU INTEND

TO DRIVE A FASTENER

Whenever the air supply is connected to the tool, never

touch the trigger unless you intend to drive a fastener into

the work. It is dangerous to walk around carrying the tool

with the trigger pulled, and this and similar actions should

be avoided.

9. NEVER POINT THE DISCHARGE OUTLET TOWARD

YOURSELF AND OTHER PERSONNEL

If the discharge outlet is pointed toward people, serious ac-

cidents may be caused when misfiring. Be sure the dis-

charge outlet is not pointed toward people when connecting

and disconnecting the hose, loading and unloading the fas-

teners or similar operations.

10. USE SPECIFIED FASTENERS

(SEE PAGE 7)

The use of fasteners other than specified fasteners will

cause the tool malfunction. Be sure to use only specified

fasteners when operating the tool.

11. PLACE THE DISCHARGE OUTLET ON THE WORK SUR-

FACE PROPERLY

Failure to place the discharge outlet of the nose in a proper

manner can result in a fastener flying up and is extremely

dangerous.

12. DO NOT DRIVE FASTENERS CLOSE TO THE EDGE

AND CORNER OF THE WORK AND THIN MATERIAL

The workpiece is likely to split and the fastener could fly free

and hit someone.

13. DO NOT DRIVE FASTENERS ON TOP OF OTHER FAS-

TENERS

Driving fasteners on the top of other fasteners may cause

deflection fasteners which could cause injury.

14. REMOVING THE FASTENERS AFTER COMPLETING

OPERATION

If fasteners are left in the magazine after the completion of

operation, there is the danger of a serious accident occur-

ring prior to the resumption of operation, should the tool be

handled carelessly, or when connecting the air fitting. For

this reason, always remove all fasteners remaining in the

magazine after completion of the operation.

15. CHECK OPERATION OF THE CONTACT TRIP MECHA-

NISM FREQUENTLY INCASE OF USING A CONTACT

TRIP TYPETOOL

Do not use the tool if the trip is not working correctly as ac-

cidental driving of a fastener may result. Do not interfere

with the proper operation of the contact trip mechanism.

16. WHEN USING THE TOOL OUTSIDE OR ELEVATED

PLACE

When fastening roofs or similar slanted surface, start fas-

tening at the lower part and gradually work your way up.

Fastening backward is dangerous as you may lose your foot

place.

Secure the hose at a point close to the area you are going

to drive fasteners. Accidents may be caused due to the

hose being pulled inadvertently or getting caught.

17. NEVER USE THE TOOL IF ANY PORTION OF THE TOOL

CONTROLS (e.g., TRIGGER, CONTACT ARM) IS INOP-

ERABLE, DISCONNECTED, ALTERED OR NOT WOK-

ING PROPERLY

18. NEVER ACTUATE THE TOOL INTO FREE SPACE

This will avoid any hazard caused by free flying fasteners

and excessive strain of the tool.

19. ALWAYS ASSUME THAT THE TOOL CONTAINS FAS-

TENERS

20. RESPECT THE TOOL AS A WORKING IMPLEMENT

21. NO HORSEPLAY

22. NEVER LOAD THE TOOL WITH FASTENERS WHEN

ANY ONE OF THE OPERATING CONTROLS (e.g., TRIG-

GER, CONTACT ARM) IS ACTIVATED

23. WHEN DISPOSING THE MACHINE OR ITS PARTS, FOL-

LOW THE RELEVANT NATIONAL RULES

OBSERVE THE FOLLOWING GENERAL CAU-

TION IN ADDITION TO THE OTHER WARNINGS

CONTAINED IN THIS MANUAL

•Do not use the tool as a hammer.

•Always carry the tool by the grip, never carry the

tool by the air hose.

•The tool must be used only for the purpose it was

designed.

•Never remove, tamper with the operating controls

(e.g., TRIGGER, CONTACT ARM)

•Keep the tool in a dry place out of reach of chil-

dren when not in use.

•Do not use the tool without Safety Warning label.

•Do not modify the tool from original design or

function without approval by MAX CO., LTD.

3. SPECIFICATIONS AND TECHNI-

CAL DATA

1. NAME OF PARTS

2. TOOL SPECIFICATIONS

3. FASTENER SPECIFICATIONS

TOOL AIR FITTINGS:

This tool uses a 1/4" N.P.T. male plug. The inside diameter should

be .28" (7 mm) or larger. The fitting must be capable of discharging

tool air pressure when disconnected from the air supply.

RECOMMENDED OPERATING PRESSURE:

70 to 100 p.s.i. (5 to 7 bar). Select the operating air pressure with-

in this range for best fastener performance.

DO NOT EXCEED 120 p.s.i. (8 bar).

4. TECHNICAL DATA

1NOISE

A-weighted single-event sound power level

------ LWA, 1s, d 100.7 dB

A-weighted single-event emission sound pressure level at

work station

------ LpA, 1s, d 93.8 dB

These values are determined and documented in accord-

ance to EN12549 : 1999.

2VIBRATION

Vibration characteristic value = 3.81 m/s2

These values are determined and documented in accord-

ance to ISO 8662-11.

This value is a tool-related characteristic value and does not

represent the influence to the hand-arm-system when using

the tool. An influence to the hand-arm-system when using

the tool will for example depend on the gripping force, the

contact pressure force, the working direction, the adjust-

ment of mains supply, the workpiece, the workpiece sup-

port.

5. APPLICATIONS

∗Fastening asphalt and fiberglass shingles

∗Siding installation

∗Fastening lath wire on the plywood

∗Wooden box assembly

4. AIR SUPPLY AND CONNEC-

TIONS

Read section titled "SAFETY INSTRUCTIONS"

DO NOT USE ANY POWER SOURCE EXCEPT AN AIR COM-

PRESSOR

The tool is designed to operate on compressed air. Do not oper-

ate the tool on any other highpressure gas, combustible gases

(e.g., oxygen, acetylene, etc.) since there is the danger of an ex-

plosion. For this reason, absolutely do not use anything other

than an air compressor to operate the tool.

OPERATE WITHIN THE PROPER AIR PRESSURE RANGE

The tool designed to operate within an air pressure range of 70

to 100 p.s.i.. (5 to 7 bar)

The pressure should be adjusted to the type of the work being

fastened. The tool shall never be operated when the operating

pressure exceeds 120 p.s.i.. (8 bar)

DO NOT OPERATE THE TOOL NEAR A FLAMMABLE SUB-

STANCE

Never operate the tool near a flammable substance (e.g., thinner,

gasoline, etc.). Volatile fumes from these substances could be

drawn into the compressor and compressed together with the air

and this could result in an explosion.

DO NOT USE A WRONG FITTINGS

The connector on the tool must not hold pressure when air supply

is disconnected. If a wrong fitting is used, the tool can remain

charged with air after disconnecting and thus will be able to drive

a fastener even after the air line is disconnected, possibly caus-

ing injury.

1Frame

2Cylinder Cap

3Contact Arm

4Nose

5Magazine

6Trigger

7Grip

8Exhaust Port

9Trigger Lock

Dial

0Shingle gauge

HEIGHT 10-5/8" (271 mm)

WIDTH 4-5/8" (116 mm)

LENGTH 12-3/8" (313 mm)

WEIGHT 5.2 lbs. (2.4 kg)

RECOMMENDED

OPERATING PRESSURE

70 to 100 p.s.i.

(5 to 7 bar)

LOADING CAPACITY 120 Nails

AIR CONSUMPTION 0.046 ft3at 90 p.s.i. (1.3 at 6 bar)

operating pressure

NAIL LENGTH 3/4" to 1-3/4" (19 to 45 mm)

SHANK DIAMETER .120" (3.0 mm)

SHANK TYPE Smooth, Ring

WARNING

Thinner Gasoline

DISCONNECT THE AIR SUPPLY AND EMPTY THE MAGAZINE

WHEN THE TOOL IS NOT IN USE

Always disconnect the air supply from the tool and empty the

magazine when operation has been completed or suspended,

when unattended, moving to a different work area, adjusting, dis-

assembling, or repairing the tool, and when clearing a jammed

fastener.

FITTINGS: Install a male plug on the tool which is free flowing

and which will release air pressure from the tool when discon-

nected from the supply source.

HOSES: Hose has a min. ID of 1/4" (6 mm) and max. length of

no more than 17" (5 meters).

The supply hose should contain a fitting that will provide "quick

disconnecting" from the male plug on the tool.

SUPPLY SOURCE: Use only clean regulated compressed air as

a power source for the tool.

3-PIECE AIRSET (Air filter, Regulator, Oiler):

Refer to TOOL SPECIFICATIONS for setting the correct operat-

ing pressure for the tool.

NOTE:

A filter will help to get the best performance and minimum wear

from the tool because dirt and water in the air supply are major

causes of wear in the tool.

Frequent, but not excessive, lubrication is required for the best

performance. Oil added thru the air line connection will lubricate

the internal parts.

5. INSTRUCTIONS FOR OPERA-

TION

Read section titled "SAFETY INSTRUCTIONS".

1. BEFORE OPERATION

Check the following prior operation.

1Wear Safety Glasses or Goggles.

2Do not connect the air supply.

3Inspect screw tightness.

4Check operation of the contact arm & trigger if moving

smoothly.

5Connect the air supply.

6Check the air-leakage. (The Tool must not have the air-

leakage.)

7Hold the Tool with finger-off the trigger, then push the con-

tact arm against the work-piece. (The tool must not oper-

ate.)

8Hold the Tool with contact arm free from work-piece and pull

the trigger. (The Tool must not operate.)

9Disconnect the air supply.

2. OPERATION

Wear safety glasses or goggles danger to the eyes always exists

due to the possibility of dust being blown up by the exhausted air

or of a fastener flying up due to the improper handling of the tool.

For these reasons, safety glasses or goggles shall always be

worn when operating the tool.

The employer and/or user must ensure that proper eye protection

is worn. Eye protection equipment must conform to the require-

ments of the American National Standards Institute, ANSI Z87.1

(Council Directive 89/686/EEC of 21 DEC. 1989) and provide

both frontal and side protection.

The employer is responsible to enforce the use of eye protection

equipment by the tool operator and all other personnel in the work

area.

NOTE: Non-side shielded spectacles and face shields alone do

not provide adequate protection.

Keep hands and body away from the discharge outlet when driv-

ing the fasteners because of dangerous of hitting the hands or

body by mistake.

[AIR SUPPLY & CONNECTIONS]

Air filter

Air hose

Regulator

3-piece airset

Used at 70 to 100 p.s.i. (5 to 7 bar)

Air compressor Oiler

WARNING

NAIL LOADING

1Open the magazine:

Pull down door latch and swing door open. Swing magazine

cover open.

2Check adjustment:

The nail support can be moved up and down to four set-

tings. To change setting pull up on the post and twist to the

correct step. The nail support should be adjusted correctly

to the position as follows;

1-3/4" (45 mm) nails - use bottom step

1-1/4", 1-1/2" (32, 38 mm) nails - use middle step

3/4", 7/8", 1" (19, 22, 25 mm) nails - use top step

3Nail loading:

Place a coil of nails over the post in the Magazine. Uncoil

enough nails to reach the Feed Pawl, and place the second

nail between the teeth on the Feed Pawl. The nail heads fit

in slot on nose.

4Swing Cover closed.

5Close the Door.

Check that latch engages. (If it does not engage, check that

the nail heads are in the slot on the Nose).

TEST OPERATION

1Adjust the air pressure at 70 p.s.i. (5 bar) and connect the

air supply.

2Without touching the Trigger, depress the Contact Arm

against the work-piece.

Pull the Trigger. (The tool must fire the fastener.)

3With the tool off the work-piece, pull the Trigger.

Then depress the Contact Arm against the work-piece.

(The tool must fire the fastener.)

4Adjust the air pressure as much as the lowest possible ac-

cording to the diameters and length of fastener and the

hardness of work-piece.

DRIVING DEPTH ADJUSTMENT DIAL

•ALWAYS disconnect air supply before Adjust-

ment dial.

1With air pressure set, drive nails into a representative mate-

rial sample to determine if adjustment is necessary.

2If adjustment is required, disconnect air supply.

Door latch

Magazine cover

Door

Nail support

Magazine

Feed pawl

Nail

Adjustment dial

WARNING

3Refer to the mark on the Contact Arm cover for direction to

turn the Adjustment dial.

4Reconnect air supply.

TRIGGER LOCK MECHANISM

The tool is equipped with a trigger lock mechanism. Push and ro-

tate the Trigger Lock Dial to the trigger free position before driving

nails.

SHINGLE GAUGE

•ALWAYS disconnect the air supply before mak-

ing adjustment.

This gauge can be used to control shingle spacing. Loosen the

screw to adjust gauge to desired shingle exposure, as shown.

CLEANING THE ROOFING NAILER

•Do not use gasoline or similar highly flammable

liquids to clean the nailer.

Vapor could be ignited by a spark causing an explosion.

Tar and dirt may build up on the Nose and Contact Arm. This can

prevent correct operation. Remove any build-up with kerosene,

#2 fuel oil or diesel fuel. Do not dunk the nailer into these solvents

beyond the height of the nail heads, to avoid getting the solvent

into the drive cylinder.

Dry off the nailer before use. Any oil film left after cleanup will ac-

celerate the tar buildup, and the nailer will require more frequent

re-cleaning.

NOTE:

Solvents sprayed on Nose to clean and free up the trip may have

the opposite effect! The solvent may soften the tar on the shin-

gles and cause tar build-up to be accelerated. Dry operation is

better, as noted above.

Deeper Shallower

Trigger lock dial

Trigger

Shingle exposure

WARNING

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Pistola de clavos de Max

Max

Max NF235F/18 Instrucciones de funcionamiento

Max

Max SN890CH2(CE) Manual de instalación y operación

Max

Max HA55SF-ST Instrucciones de funcionamiento

Max

Max SN890CH/34 Instrucciones de funcionamiento

Max

Max PowerLite HA65Q/15-11 Manual de instrucciones

Max

Max NF201/18-35 Instrucciones de funcionamiento

Max

Max CN890S Instrucciones de funcionamiento

Max

Max GS865E Instrucciones de funcionamiento

Max

Max CN80 Instrucciones de funcionamiento

Max

Max SuperFramer SN883RH2 Instrucciones de funcionamiento

Max

Max SuperSider CN565S2(CE) Instrucciones de funcionamiento

Max

Max NF550/15-65 Instrucciones de funcionamiento

Max

Max NF665A/15 Instrucciones de funcionamiento

Max

Max NF255FA/18 Manual de instrucciones

Max

Max GS732C LT Instrucciones de funcionamiento

Max

Max SN883CH/34 (CE) Instrucciones de funcionamiento

Max

Max SuperLocator SN438J Manual de instrucciones

Max

Max GS683RH-EX Instrucciones de funcionamiento

Max

Max NF255SF-ST Instrucciones de funcionamiento

Max

Max NF665/15 Instrucciones de funcionamiento

Max

Max PowerLite HN65 Manual de instrucciones

Max

Max CN450R Instrucciones de funcionamiento

Max

Max HN50 Instrucciones de funcionamiento

Max

Max SuperSider CN565S2 Instrucciones de funcionamiento

Manuales populares de Pistola de clavos de otras marcas

Performance Tool

Performance Tool M643 Manual de usuario

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Manual de usuario

Parkside

Parkside PET 25 B1 Manual de usuario

Senco

Senco Fusion Technology F-35XP Manual de usuario

Grizzly

Grizzly G1847 Manual de usuario

Ryobi

Ryobi R18N18G Manual de usuario

Black & Decker

Black & Decker 492848-00 Manual de usuario

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Manual de usuario

Metabo HPT

Metabo HPT NR 3690DC Manual de instrucciones

Surtek

Surtek CN650 Dimensiones y guía de instalación

Makita

Makita GF600 Manual de usuario

Parkside

Parkside PET 25 B1 Manual de usuario

Senco

Senco AirFree 25 Manual de usuario

Freeman

Freeman P50LSLW Manual de usuario

Aicon PRO

Aicon PRO DAC4507 Manual de usuario

DAJ

DAJ XR150A Manual de usuario

Makita

Makita AN923 Manual de usuario

Grizzly

Grizzly T20644 Manual de usuario