Max SN883CH/34 (CE) Instrucciones de funcionamiento

SN883CH/34(CE)

34 DEGREE CLIPPED HEAD FRAMING

STICK NAILER

34-GRAD BEFESTIGTER RAHMEN-

STOCKHAUPTNAGLER

CLOUEUSE À MANCHE D’ENCADREMENT

DE TÊTE COUPÉE À 34 DEGRÉS

INCHIODATRICE A MANICA DI QUADRO

DI TESTA TAGLIATA A 34 GRADI

CLAVADORA DE BARRA DE MARCO

DE CABEZA CORTADA A 34 GRADOS

OPERATING and MAINTENANCE MANUAL

BETRIEBSANLEITUNG

MANUEL D’UTILISATION et D’ENTRETIEN

MANUALE DI FUNZIONAMENTO E MANUTENZIONE

MANUAL DE OPERACIONES Y MANTENIMIENTO

BEFORE USING THIS TOOL, STUDY THIS MANUAL TO ENSURE SAFETY WARNING AND

INSTRUCTIONS.

KEEP THESE INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE.

WARNING

LESEN SIE VOR INBETRIEBNAHME DES GERÄTES DIE GEBRAUCHS- UND SICHERHEITS-

HINWEISE. BITTE BEWAHREN SIE DIE GEBRAUCHS- UND SICHERHEITSHINWEISE AUF,

DAMIT SIE AUCH SPÄTER EINGESEHEN WERDEN KÖNNEN.

ACHTUNG

AVANT D’UTILISER CET OUTIL, LIRE CE MANUEL ET LES CONSIGNES DE SECURITE

AFIN DE GARANTIR UN FONCTIONNEMENT SUR.

CONSERVER CE MANUEL EN LIEU SUR AVEC L’OUTIL AFIN DE POUVOIR LE

CONSULTER ULTERIEUREMENT.

AVERTISSEMENT

PRIMA DI USARE QUESTA MACCHINA, STUDIARE IL MANUALE PER PRENDERE ATTO

DEGLI AVVERTIMENTI E DELLE ISTRUZIONIPER LA SICUREZZA.

TENERE QUESTE ISTRUZIONI INSIEME ALLO STRUMENTO PER CONSULTAZIONI FUTURE.

ATTENZIONE

PARA EVITAR GRAVES DAÑOS PERSONALES O EN LA PROPIEDAD.

ANTES DE EMPLEAR LA HERRAMIENTA, LEER CON ATENCIÓN Y COMPRENDER LOS

SIGUIENTES INSTRUCCIONES DE SEGURIDAD.

ATENCIÓN

DEFINITIONS OF SIGNAL WORDS

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death

or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or

moderate injury.

NOTE: Emphasizes essential information.

DEFINITIONEN DER HINWEISBEZEICHNUNGEN

ACHTUNG! Zeigt eine eventuell gefährliche Situation an, die den Tod oder schwere Verletzungen

zur Folge haben könnte, wenn sie nicht vermieden wird.

VORSICHT! Zeigt eine eventuell gefährliche Situation an, die leichte oder mittelschwere

Verletzungen zur Folge haben könnte, wenn sie nicht vermieden wird.

HINWEIS: Hebt wichtige Informationen hervor.

DÉFINITIONS DES DIFFÉRENTS DEGRÉS D’ AVERTISSEMENTS

AVERTISSEMENT Indique une situation éventuellement dangereuse qui, si elle n’est pas contournée,

pourrait provoquer la mort ou des blessure sérieuses.

ATTENTION Indique une situation éventuellement dangereuse qui, si elle n’est pas contournée,

pourrait provoquer des blessures légères à moyennement sérieuses.

REMARQUE Souligne des informations importantes.

DEFINIZIONE DELLE INDICAZIONI DI AVVERTIMENTO

ATTENZIONE: Indica l’eventualità che possa verificarsi una situazione pericolosa, la quale se non

viene evitata, può risultare letale o provocare gravi lesioni.

AVVERTENZA: Indica l’eventualità che possa verificarsi una situazione pericolosa, la quale se non

viene evitata, può provocare lesioni di lieve o media entità.

NOTA: Evidenzia informazioni importanti.

DEFINICIÓN DE LAS INDICACIONES DE ADVERTENCIA

¡ATENCIÓN! Indica una situación potencialmente peligrosa que podría causar la muerte o graves

lesiones si no se evita.

¡PRECAUCIÓN! Indica una situación potencialmente peligrosa que podría causar lesiones menos

graves o leves si no se evita.

NOTA: Resalta informaciones importantes.

ENGLISH Page 3 to 15 Page

DEUTSCH Page 17 to 29 Page

FRANÇAIS Page 31 to 43 Page

ITALIANO Page 45 to 57 Page

ESPAÑOL Page 59 to 71 Page

INDEX INHALTSVERZEICHNIS INDEX INDICE INDICE

OPERATING and MAINTENANCE MANUAL

ENGLISH

INDEX

1. SAFETY INSTRUCTIONS

……………………………………………

2. SPECIFICATIONS & TECHNICAL DATA

………………………………

3. AIR SUPPLY AND CONNECTIONS

……………………………………

4. INSTRUCTIONS FOR OPERATION

……………………………………

5. MAINTENANCE

………………………………………………………

6. STORAGE

………………………………………………………………

7. TROUBLESHOOTING/REPAIRS

………………………………………

BEFORE USING THIS TOOL, STUDY THIS MANUAL TO ENSURE SAFETY

WARNING AND INSTRUCTIONS.

KEEP THESE INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE.

WARNING

1. SAFETY INSTRUCTIONS

TO AVOID SEVERE PERSONAL INJURY OR

PROPERTY DAMAGE

BEFORE USING THE TOOL, READ

CAREFULLY AND UNDERSTAND THE

FOLLOWING “SAFETY INSTRUCTIONS”.

FAILURE TO FOLLOW WARNINGS COULD

RESULT IN DEATH OR SERIOUS INJURY.

WARNING

1. WEAR SAFETY GLASSES OR GOGGLES

Danger to the eyes always exists due to the

possibility of dust being blown up by the

exhausted air or of a fastener flying up due to

the improper handling of the tool. For these

reasons, safety glasses or goggles shall

always be worn when operating the tool.

The employer and/or user must ensure that

proper eye protection is worn. Eye protection

equipment must conform to the requirements

of Council Directive 89/686/EEC of 21 DEC.

1989 (the American National Standards

Institute, ANSI Z87.1) and provide both frontal

and side protection.

The employer is responsible to enforce the

use of eye protection equipment by the tool

operator and all other personnel in the work

area.

NOTE: Non-side shielded spectacles and

face shields alone do not provide adequate

protection.

PRECAUTIONS ON USING THE TOOL

ENGLISH

2. EAR PROTECTION MAY BE REQUIRED IN

SOME ENVIRONMENTS

As the working condition may include

exposure to high noise levels which can lead

to hearing damage, the employer and user

should ensure that any necessary hearing

protection is provided and used by the

operator and others in the work area.

3. DO NOT USE ANY POWER SOURCE

EXCEPT AN AIR COMPRESSOR

The tool is designed to operate on

compressed air. Do not operate the tool on

any other highpressure gas, combustible

gases (e.g., oxygen, acetylene, etc.) since

there is the danger of an explosion. For this

reason, absolutely do not use anything other

than an air compressor to operate the tool.

4. OPERATE WITHIN THE PROPER AIR

PRESSURE RANGE

The tool is designed to operate within an air

pressure range of 5 to 7 bar (70 to 100 p.s.i.).

The pressure should be adjusted to the type

of the work being fastened. The tool shall

never be operated when the operating

pressure exceeds 8 bar (120 p.s.i.).

Never connect the tool to air pressure which

potentially exceeds 14 bar (200 p.s.i.) as the

tool can burst.

5. DO NOT OPERATE THE TOOL NEAR A

FLAMMABLE SUBSTANCE

Never operate the tool near a flammable

substance (e.g., thinner, gasoline, etc.).

Volatile fumes from these substances could

be drawn into the compressor and

compressed together with the air and this

could result in an explosion.

6. NEVER USE THE TOOL IN AN EXPLOSIVE

ATMOSPHERE

Sparks from the tool may ignite atmospheric

gases, dust or other combustible materials.

7. DO NOT USE A WRONG FITTINGS

The connector on the tool must not hold

pressure when air supply is disconnected. If a

wrong fitting is used, the tool can remain

charged with air after disconnecting and thus

will be able to drive a fastener even after the

air line is disconnected, possibly causing

injury.

8. DISCONNECT THE AIR SUPPLY AND

EMPTY THE MAGAZINE WHEN THE TOOL

IS NOT IN USE

Always disconnect the air supply from the tool

and empty the magazine when operation has

been completed or suspended, when

unattended, moving to a different work area,

adjusting, disassembling, or repairing the tool,

and when clearing a jammed fastener.

100

Thinner Gasoline

ENGLISH

12. USE SPECIFIED FASTENERS

(SEE PAGE 7)

The use of fasteners other than specified

fasteners will cause the tool malfunction. Be

sure to use only specified fasteners when

operating the tool.

13. PLACE THE DISCHARGE OUTLET ON THE

WORK SURFACE PROPERLY

Failure to place the discharge outlet of the

nose in a proper manner can result in a

fastener flying up and is extremely

dangerous.

14. KEEP HANDS AND BODY AWAY FROM

THE DISCHARGE OUTLET

When loading and using the tool, never place

a hand or any part of body in fastener

discharge area of the tool. It is very

dangerous to hit the hands or body by

mistake.

15. DO NOT DRIVE FASTENERS CLOSE TO

THE EDGE AND CORNER OF THE WORK

AND THIN MATERIAL

The workpiece is likely to split and the

fastener could fly free and hit someone.

9. INSPECT SCREW TIGHTNESS

Loose or improperly installed screws or bolts

cause accidents and tool damage when the

tool is put into operation. Inspect to confirm

that all screws and bolts are tight and

properly installed prior to operating the tool.

10. DO NOT TOUCH THE TRIGGER UNLESS

YOU INTEND TO DRIVE A FASTENER

Whenever the air supply is connected to the

tool, never touch the trigger unless you intend

to drive a fastener into the work. It is

dangerous to walk around carrying the tool

with the trigger pulled, and this and similar

actions should be avoided.

11. NEVER POINT THE DISCHARGE OUTLET

TOWARD YOURSELF AND OTHER

PERSONNEL

If the discharge outlet is pointed toward

people, serious accidents may be caused

when misfiring. Be sure the discharge outlet

is not pointed toward people when connecting

and disconnecting the hose, loading and

unloading the fasteners or similar operations.

ENGLISH

20. NEVER USE THE TOOL IF ANY PORTION

OF THE TOOL CONTROLS (e.g., TRIGGER,

CONTACT ARM) IS INOPERABLE,

DISCONNECTED, ALTERED OR NOT

WOKING PROPERLY

21. NEVER ACTUATE THE TOOL INTO FREE

SPACE

This will avoid any hazard caused by free

flying fasteners and excessive strain of the

tool.

22. ALWAYS ASSUME THAT THE TOOL

CONTAINS FASTENERS

23. RESPECT THE TOOL AS A WORKING

IMPLEMENT

24. NO HORSEPLAY

25. NEVER LOAD THE TOOL WITH

FASTENERS WHEN ANY ONE OF THE

OPERATING CONTROLS (e.g., TRIGGER,

CONTACT ARM) IS ACTIVATED

26. WEAR THE GLOVES DEPENDING ON THE

WORKING CONDITION

27. WHEN DISPOSING THE MACHINE OR ITS

PARTS, FOLLOW THE RELEVANT

NATIONAL RULES

OBSERVE THE FOLLOWING GENERAL

CAUTION IN ADDITION TO THE OTHER

WARNINGS CONTAINED IN THIS

MANUAL

•Do not use the tool as a hammer.

•Always carry the tool by the grip, never

carry the tool by the air hose.

•The tool must be used only for the purpose

it was designed.

•Never remove, tamper with the operating

controls (e.g., TRIGGER, CONTACT ARM)

•Keep the tool in a dry place out of reach of

children when not in use.

•Do not use the tool without Safety Warning

label.

•Do not modify the tool from original design

or function without approval by MAX CO.,

LTD.

16. DO NOT DRIVE FASTENERS ON TOP OF

OTHER FASTENERS

Driving fasteners on the top of other fasteners

may cause deflection fasteners which could

cause injury.

17. REMOVING THE FASTENERS AFTER

COMPLETING OPERATION

If fasteners are left in the magazine after the

completion of operation, there is the danger

of a serious accident occurring prior to the

resumption of operation, should the tool be

handled carelessly, or when connecting the

air fitting. For this reason, always remove all

fasteners remaining in the magazine after

completion of the operation.

18. CHECK OPERATION OF THE CONTACT

TRIP MECHANISM FREQUENTLY IN CASE

OF USING A CONTACT TRIP TYPE TOOL

Do not use the tool if the trip is not working

correctly as accidental driving of a fastener

may result. Do not interfere with the proper

operation of the contact trip mechanism.

19. WHEN USING THE TOOL OUTSIDE OR

ELEVATED PLACE

When fastening roofs or similar slanted

surface, start fastening at the lower part and

gradually work your way up. Fastening

backward is dangerous as you may lose your

foot place.

Secure the hose at a point close to the area

you are going to drive fasteners. Accidents

may be caused due to the hose being pulled

inadvertently or getting caught.

ENGLISH

1. NAME OF PARTS

2. TOOL SPECIFICATIONS

3. FASTENER SPECIFICATIONS

Frame

Cylinder Cap

Contact Arm

Nose

Magazine

Trigger

Grip

Exhaust Cover

Pusher

Adjustment Dial

2. SPECIFICATIONS AND TECHNICAL DATA

PRODUCT NO. SN883CH/34 (CE)

HEIGHT 310 mm (12-1/4”)

WIDTH 121 mm (4-3/4”)

LENGTH 440 mm (17-3/8”)

WEIGHT 3.2 kg (7.1 lbs.)

RECOMMENDED

5 to 7 bar (70 to 100 p.s.i.)

OPERATING PRESSURE

LOADING CAPACITY 90 Nails

AIR CONSUMPTION 2.18Rat 6 bar (90 p.s.i.)

operating pressure

PRODUCT NO. SN883CH/34 (CE)

NAIL LENGTH 50 to 83 mm (2” to 3-1/4”)

SHANK DIAMETER 2.9 to 3.3 mm (.113” to .131”)

SHANK TYPE Smooth, Ring, Screw

HEAD DIAMETER 6.5 to 7.7 mm (.256” to .303”)

COLLATION ANGLE 34 degree

HEAD Clipped head

＊The machine has been designed

compact so that you can use it in

the narrow space.

ENGLISH

TOOL AIR FITTINGS:

This tool uses a 3/8” N.P.T. male plug. The inside

diameter should be 9.9mm (.39”) or larger. The

fitting must be capable of discharging tool air

pressure when disconnected from the air supply.

RECOMMENDED OPERATING

PRESSURE:

5 to 7 bar (70 to 100 p.s.i.). Select the operating

air pressure within this range for best fastener

performance.

DO NOT EXCEED 8 bar (120 p.s.i.).

5. APPLICATIONS

＊Floor and wall framing

＊Subflooring

＊Roof and wall sheathing

＊Fencing

4. TECHNICAL DATA

qNOISE

A-weighted single-event sound power level

------ LWA, 1s, d 94.6 dB

A-weighted single-event emission sound

pressure level at work station

------- LpA, 1s, d 90.28 dB

These values are determined and documented

in accordance to EN12549 : 1999.

wVIBRATION

Vibration characteristic value ＝4.1 m/s

These values are determined and documented

in accordance to ISO 8662-11.

This value is a tool-related characteristic value

and does not represent the influence to the

hand-arm-system when using the tool. An

influence to the hand-arm-system when using

the tool will, for example, depend on the

gripping force, the contact

pressure force, the working

direction, the adjustment of

mains supply, the

workpiece, the workpiece

support.

3. AIR SUPPLY AND

CONNECTIONS

Read section titled “SAFETY

INSTRUCTIONS”.

DO NOT USE ANY POWER SOURCE EXCEPT

AN AIR COMPRESSOR

The tool is designed to operate on compressed

air. Do not operate the tool on any other

highpressure gas, combustible gases (e.g.,

oxygen, acetylene, etc.) since there is the danger

of an explosion. For this reason, absolutely do not

use anything other than an air compressor to

operate the tool.

OPERATE WITHIN THE PROPER AIR

PRESSURE RANGE

The tool designed to operate within an air

pressure range of 5 to 7 bar (70 to 100 p.s.i.).

The pressure should be adjusted to the type of

the work being fastened. The tool shall never be

operated when the operating pressure exceeds 8

bar (120 p.s.i.).

WARNING

100

ENGLISH

DO NOT OPERATE THE TOOL NEAR A

FLAMMABLE SUBSTANCE

Never operate the tool near a flammable

substance (e.g., thinner, gasoline, etc.). Volatile

fumes from these substances could be drawn into

the compressor and compressed together with

the air and this could result in an explosion.

DO NOT USE A WRONG FITTINGS

The connector on the tool must not hold pressure

when air supply is disconnected. If a wrong fitting

is used, the tool can remain charged with air after

disconnecting and thus will be able to drive a

fastener even after the air line is disconnected,

possibly causing injury.

DISCONNECT THE AIR SUPPLY AND EMPTY

THE MAGAZINE WHEN THE TOOL IS NOT IN

USE

Always disconnect the air supply from the tool

and empty the magazine when operation has

been completed or suspended, when unattended,

moving to a different work area, adjusting,

disassembling, or repairing the tool, and when

clearing a jammed fastener.

FITTINGS: Install a male plug on the tool which is

free flowing and which will release air pressure

from the tool when disconnected from the supply

source.

HOSES: Hose has a min. ID of 6 mm (1/4”) and

max. length of no more than 5 meters (17”).

The supply hose should contain a fitting that will

provide “quick disconnecting” from the male plug

on the tool.

SUPPLY SOURCE: Use only clean regulated

compressed air as a power source for the tool.

3-PIECE AIRSET (Air filter, Regulator, Oiler):

Refer to TOOL SPECIFICATIONS for setting the

correct operating pressure for the tool.

NOTE:

A filter will help to get the best performance and

minimum wear from the tool because dirt and

water in the air supply are major causes of wear

in the tool.

Frequent, but not excessive, lubrication is

required for the best performance. Oil added thru

the air line connection will lubricate the internal

parts.

Air compressor

[AIR SUPPLY & CONNECTIONS]

Air filter

Air hose

Oiler

Used at 5 to 7 bar (70 to 100 p.s.i.)

Regulator

[AIR SUPPLY & CONNECTIONS]

3-piece airset

100

Thinner Gasoline

ENGLISH

4. INSTRUCTIONS FOR

OPERATION

2. OPERATION

Wear safety glasses or goggles. Danger to the

eyes always exists due to the possibility of dust

being blown up by the exhausted air or of a

fastener flying up due to the improper handling of

the tool. For these reasons, safety glasses or

goggles shall always be worn when operating the

tool.

The employer and/or user must ensure that

proper eye protection is worn. Eye protection

equipment must conform to the requirements of

Council Directive 89/686/EEC of 21 DEC. 1989

(the American National Standards Institute, ANSI

Z87.1) and provide both frontal and side

protection.

The employer is responsible to enforce the use of

eye protection equipment by the tool operator and

all other personnel in the work area.

NOTE: Non-side shielded spectacles and face

shields alone do not provide adequate protection.

WARNING

Keep hands and body away from the discharge

outlet when driving the fasteners because of

dangerous of hitting the hands or body by

mistake.

Nails

Read section titled “SAFETY

INSTRUCTIONS”.

1. BEFORE OPERATION

Check the following prior operation.

Wear Safety Glasses or Goggles.

Do not connect the air supply.

Inspect screw tightness.

Check operation of the contact arm & trigger if

moving smoothly.

Connect the air supply.

Check the air-leakage. (The Tool must not

have the air-leakage.)

Hold the Tool with finger-off the trigger, then

push the contact arm against the work-piece.

(The tool must not operate.)

Hold the Tool with contact arm free from work-

piece and pull the trigger. (The Tool must not

operate.)

Disconnect the air supply.

NAIL LOADING

●

When loading the nails, be sure to release

the finger from the Trigger.

●

Do not press the Contact Arm against the

object.

PROCEDURE

Load the nails into the slot in the rear of the

Magazine until they go over the Nail Stopper.

WARNING

Nail Stopper

Tabla de contenidos

Otros manuales de Pistola de clavos de Max

Max

Max SuperSider CN565S2 Instrucciones de funcionamiento

Max

Max NF665A/15 Instrucciones de funcionamiento

Max

Max SuperSider CN565S2(CE) Instrucciones de funcionamiento

Max

Max SN890CH/34 Instrucciones de funcionamiento

Max

Max GS683RH-EX Instrucciones de funcionamiento

Max

Max CN238D Instrucciones de funcionamiento

Max

Max HA55SF-ST Instrucciones de funcionamiento

Max

Max SuperLocator SN438J Manual de instrucciones

Max

Max NF235F/18 Instrucciones de funcionamiento

Max

Max NF255FA/18 Manual de instrucciones

Max

Max NF550/15-65 Instrucciones de funcionamiento

Max

Max CN450R Instrucciones de funcionamiento

Max

Max SuperRoofer CN445R2 Instrucciones de funcionamiento

Max

Max SN883-90CH/34(CE) Instrucciones de funcionamiento

Max

Max CN650M Instrucciones de funcionamiento

Max

Max NF255SF-ST Instrucciones de funcionamiento

Max

Max SN890CH2(CE) Manual de instalación y operación

Max

Max NF201/18-35 Instrucciones de funcionamiento

Max

Max CN890S Instrucciones de funcionamiento

Max

Max NF565/16 Instrucciones de funcionamiento

Max

Max CN55 Manual de instrucciones

Max

Max GS865E Instrucciones de funcionamiento

Max

Max SN883RH Instrucciones de funcionamiento

Max

Max PowerLite HA55SF2/18 Manual de instrucciones

Manuales populares de Pistola de clavos de otras marcas

Performance Tool

Performance Tool M643 Manual de usuario

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Manual de usuario

Parkside

Parkside PET 25 B1 Manual de usuario

Senco

Senco Fusion Technology F-35XP Manual de usuario

Grizzly

Grizzly G1847 Manual de usuario

Ryobi

Ryobi R18N18G Manual de usuario

Black & Decker

Black & Decker 492848-00 Manual de usuario

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Manual de usuario

Metabo HPT

Metabo HPT NR 3690DC Manual de instrucciones

Surtek

Surtek CN650 Dimensiones y guía de instalación

Makita

Makita GF600 Manual de usuario

Parkside

Parkside PET 25 B1 Manual de usuario

Senco

Senco AirFree 25 Manual de usuario

Freeman

Freeman P50LSLW Manual de usuario

Aicon PRO

Aicon PRO DAC4507 Manual de usuario

DAJ

DAJ XR150A Manual de usuario

Makita

Makita AN923 Manual de usuario

Grizzly

Grizzly T20644 Manual de usuario