MasterCraft 055-6755-8 Manual de usuario

TABLE SAW

WITH HEAVY-DUTY STEEL STAND

Item No.: 055-6755-8

Instruction Manual

Toll-Free Helpline

1-800-689-9928

Table of contents

I. Specifications

SECTION PAGE

II.

III.

IV.

VI.

VII.

VIII.

IX.

Specifications........................................................................

General safety guidelines.....................................................

Electrical information.............................................................

Know your table saw.............................................................

Assembly and adjustments...................................................

Operating instructions...........................................................

Maintenance.........................................................................

Troubleshooting....................................................................

Warranty................................................................................

Parts list................................................................................

MODEL:

MOTOR:

MOTOR SPEED:

TABLE SIZE:

BLADE SIZE:

MAXIMUM DEPTH OF CUT AT 90°:

MAXIMUM DEPTH OF CUT AT 45°:

WEIGHT:

055-6755-8

120 V 60 Hz 15 A

5000 RPM (no load)

650 x 434mm

10" (24-tooth) carbide-tipped

3" (7.6 cm)

2 1/2" (6.4 cm)

45 lb (20.5 kg)

II. General safety guidelines

WARNING: Read all the safety guidelines and instructions before you use this electric power

tool!

WARNING! When using electrical power tools, the following essential safety measures have to

be observed to prevent electric shocks, injury and fire hazards. Failure to adhere to the safety

guidelines and instructions can cause electric shock, fire and/or severe injuries.

1. Store all safety guidelines and instructions for future use.

2. This device is not intended for use by people (including children) lacking experience with

electrical power tools unless they have receieved instructions about how the device is to be

used. Children have to be supervised to ensure that they do not play with the device.

3. Store the operating instructions so that they are always available to the user of the tool when

it is being operated.

4. Remove the protection padding found around the motor before using.

5. Pay close attention to instructions on reducing the risk of kickback.

6. Always use push sticks when ripping narrow workpiece and when making non-through cuts.

7. If you lend this device to other people, always hand over these operating instructions to ensure

safe use. Instruct inexperienced people in accordance with these safety instructions.

8. Keep your work area tidy. Untidiness in your work area can cause accidents.

9. Pay attention to the surrounding conditions. Do not expose the electric power tool to rain. Do

not use electric power tools in damp or wet conditions. Ensure that the work area is well lit.

Do not use electric power tools where there is a danger of fire or explosion.

10. Protect yourself against electric shocks. Avoid bodily contact with earthed parts (e.g. pipes,

radiators, electric hobs or cooling appliances).

11. Keep other people away from the work area. Do not let other people, especially children, touch

the electric power tool or the power cable. Keep them away from your work area.

12. Store unused electric power tools safely. Unused electric power tools should be stored in a dry,

high-lying or locked place, out of the reach of children.

13. Do not overload your electric power tool. It works better and more securely within the stated

output range.

14. Use the correct electric power tool. Do not use inefficient machines for heavy work. Do not use

the electric power tool for purposes for which it was not intended for. For example, do not

use circular saws to cut wooden masts or logs.

15. Wear suitable clothing. Do not wear baggy clothing or jewellery, as they can be caught

by moving parts. When working outdoors, anti-slip shoes are recommended. If you have long

hair, wear a hair net.

16. Wear safety equipment. Wear safety goggles. If the work creates dust, wear a dust mask.

17. Attach the dust extraction unit. If there are connections for dust extraction and collection

equipment, then make sure that the equipment is correctly attached and used.

18. Never use the cable for purposes for which it is not intended. Do not use the cable to pull the

plug out of the power socket. Protect the cable from heat, oil and sharp edges.

19. Secure the workpiece. When necessary use clamping devices to secure the workpiece. The

workpiece is thereby secured better than by hand.

20. Avoid taking abnormal stances. Make sure you stand securely and keep your balance at all

times.

21. Look after your tool with care. Keep the cutting tool sharp and clean so that you are able to

work better and more safely with it. Observe the guidelines on lubrication and exchanging tools.

Check the power cable of the electric power tool regularly and in case of damage let a recognized

specialist repair it. Check extension cords regularly and replace them if they are damaged.

Keep the handles dry, clean and free of oil and grease.

22. Pull the plug out of the power socket when the electric power tool is not in use, before

maintenance and when exchanging tools such as saw blades, drills and mills.

23. Do not leave keys in the device. Before you switch the device off, check that keys and setting

tools have been removed.

24. Avoid starting-up the device accidentally. Make sure that when you insert the plug into

the power socket, the power switch is turned off.

25. Use an extension cord when working outdoors. Only use extension cords outdoors which are

authorized for outdoor use and are correspondingly marked.

26. Be attentive. Be carefully what you do. Carry out your work sensibly.

27. Check the electric power tool for any sign of damage. Before continuing work with the electric power

tool, safety devices or easily damaged parts have to be carefully checked to ensure that they

function properly and are not defective. Check that moving parts are working properly and are

not or damaged. All parts must be correctly assembled by an experienced individual, unless

stated otherwise in the operating instructions, and meet all required conditions in order

II. General safety guidelines (continued)

KEEP THIS USER’S MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE

ALWAYS WEAR EYE PROTECTION THAT CONFORMS WITH CSA

REQUIREMENTS.

FLYING DEBRIS can cause permanent eye damage.

Prescription eyeglasses are not a replacement for proper eye protection.

WARNING! EXPOSURE TO EXCESSIVE NOISE LEVELS CAN RESULT IN PERMANENT

HEARING LOSS. ALWAYS WEAR EAR PROTECTION (SAFETY EAR MUFFS OR EAR

PLUGS) TO REDUCE NOISE LEVELS WHEN OPERATING THE TABLE SAW.

to guarantee that the electric power tool functions without a problem. Damaged switches have

to be replaced by a qualified electrician. Do not use electric power tools if the power switch

cannot be turned on and off.

28. WARNING! The use of other insertion tools and accessories can present a danger of injury.

to you.

29. Let a specialist electrician repair your electric power tool. This electric power tool corresponds

to the applicable safety conditions. Repairs are only allowed to be carried out by a specialist

electrician, using original replacement parts; otherwise accidents may occur.

Additional safety guidelines for circular table saws

30. No other people may stand in the direct vicinity of the machine when it is in use. People not

operating the machine must maintain a suitable safe distance!

31. Never lay the power cable over the machine table!

32. Use the push rod to pass the workpiece safely into the saw blade! Do not come too close to

the saw blade!

33. Make sure that the thickness of the material to be cut is less than the maximum possible

cutting depth.

34. Never cut “hands-free”! The workpiece must always lie level on the machine table and

be moved along the stop! The workpiece must always be pressed hard against the stop!

35. Never cut workpieces that are so small that they cannot be safety pressed against the stop

and could turn!

36. Never cut workpieces that are so small that they cannot be moved by the push rod at a safe

distance from the saw blade!

37. Only cut one workpiece at a time! Never cut several workpieces simultaneously! Workpieces

must not be placed behind or on top of each other!

38. There is a danger of the workpiece “jamming” and slipping away!

39. Make sure that the workpiece cannot slip while cutting or get jammed in the saw blade!

40. Clean the work area and the workpiece after each cut.

41. Never reach into the openings of the device! Never insert objects into the openings of the device

(e.g. the saw blade casing, dust extraction adaptor). Danger of cuts! Never reach around or

over saw blade.

II. General safety guidelines (continued)

KEEP THIS USER’S MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE

WARNING! Switch the device off, remove the plug from the power socket and let the machine

come to a standstill! No foreign bodies are allowed to be on the workpiece or the machine

table! Cut pieces of the workpiece can be caught by the rotating cutting disc and be

flung from the tool and work area.

42. Never remove the cutting piece if the machine is still switched on or running! Danger of cutting

yourself!

43. Cut workpieces may have sharp edges, ridges or wooden splinters! Danger of cutting injuries!

44. Always switch the machine off and remove the power plug when you leave the machine.

45. Never expose the device to rain or extreme moisture!

46. Do not perform any cuts with this circular table saw other than those described in these

operating instructions! Seams and notches must not be sawn!

47. Circular saws must not be used for slitting (notches which end in the workpiece)!

48. Failure to comply with these warnings may result in serious personal injury.

II. General safety guidelines (continued)

KEEP THIS USER’S MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE

GUIDELINES FOR USING EXTENSION CORDS

Make sure your extension cord is properly wired and in good condition. Always replace a damaged

extension cord, or have it repaired by a qualified person before using it. Protect your extension cords

from sharp objects, excessive heat, and damp or wet areas.

Use a separate electrical circuit for your tools. This circuit must consist of not less than #12 wire

with a 20 A time-delayed fuse or a #14 wire with a 15 A time-delayed fuse. Before connecting the

motor to the power line, make sure the switch is in the OFF position and the electric current is rated

the same as the current stamped on the motor nameplate. Running at a lower voltage will damage

the motor.

WARNING: THIS TABLE SAW IS INTENDED FOR INDOOR USE ONLY. DO NOT EXPOSE

IT TO RAIN OR USE IT IN DAMP LOCATIONS.

Make sure the extension cord is in good condition. When using an extension cord, be sure to use

one that is heavy enough to carry the current that your product will draw. An undersized cord will

cause a drop in line voltage, which will result in loss of power and overheating. The table below

shows the correct size to be used according to cord length and nameplate ampere rating. When

in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

MINIMUM GAUGE FOR EXTENSION CORDS (AWG)

(when using 120 V only)

Ampere rating Total length of cord

More than Not more than

25’ (7.6 m)

50’ (15.2 m)

100’ (30.5 m)

150’ (45.7 m)

Not recommended

III. Electrical information

IV. Know your table saw

1 Blade guard

2 Mitre gauge

3 Working table

4 Blade bevel lock knob

5 ON/OFF switch with key

6 Stand

7 Rubber foot

8 Rip fence

9 Table insert

10 Push sticker

11 Locking lever

12 Blade height/bevel adjusting handwheel

13 Saw blade

14 Anti-kickback pawls

Fig. 1

13 14

WARNING:

• IF ANY PART IS MISSING OR DAMAGED, DO NOT PLUG IN THE TABLE SAW UNTIL YOU

HAVE REPLACED THE MISSING OR DAMAGED PARTS. CALL THE TOLL FREE HELPLINE

AT 1-800-689-9928 FOR MORE INFORMATION.

• TO AVOID INJURY, THE STYROFOAM BLOCK SHOULD BE REMOVED BETWEEN THE

MOTOR AND THE TABLE.

UNPACKING

1. Carefully remove the table saw from the carton.

2. Separate the parts.

3. Lay out all of the parts, and check them against the parts listed below. Examine all of the parts

carefully.

Table saw Blade guard Kickback-pawls Mitre gauge

Push stick

Stand Legs (A)

Short bottom

leg brackets (E) Screw M6 x 12 Spring washer 6

Rubber feet Manual

Bolt M6 x 25

Flat washer 6 Hex nut M6

Long top leg

brackets (B)

Long bottom

leg brackets (C)

Short top

leg brackets (D)

Rip fence Push stick

storage screws

Blade wrench

V. Assembly and adjustments

10”TABLE SAW

Item No.:055-6755-8

Instruction Manual

Toll-FreeHelpline

1-800-689-9928

TO ASSEMBLE THE LEG STAND (Fig. 2-5)

1. Unpack all parts, and group them by type and size.

Refer to the parts list for correct quantities, see

Page. 9.

2. Attach one long top leg bracket (B) to the top of one

leg (A) using a screw, flat washer, spring washer and

hex nut. (Fig. 2)

NOTE: Do not tighten the bolts until the stand is

properly aligned (see step #8).

3. Attach other end of the long top leg bracket (B) to top

of another leg (A) using using a screw, flat washer,

spring washer and hex nut.

4. Attach one long bottom leg bracket (C) to the centre

of each leg (A) using a screw, flat washer, spring

washer and hex nut. This completes the front

frame section. (Fig. 3)

5. Assemble the rear frame section in exactly the same

manner.

6. Join the front and rear frame assemblies to the two

short upper supports (D) and two short bottom

supports (E) using a screw, flat washer, spring washer

and hex nut. (Fig. 4)

7. Insert the rubber foot to the bottom of each leg.

(Fig. 5)

8. Place the stand on a level surface, and adjust it so

WARNING: DO NOT CONNECT THE PLUG TO THE OUTLET UNTIL ALL INSTALLATIONS

AND ADJUSTMENTS HAVE BEEN COMPLETED AND YOU HAVE READ AND UNDERSTOOD

THE SAFETY AND OPERATIONAL INSTRUCTIONS.

MOUNTING HOLES (Fig. 1)

The table saw must be mounted to a firm supporting

surface such as workbench or leg stand. Four bolt

holes have been provided in the saw’s base for this

purpose. Each of the four mounting holes should be

bolted securely using 1/4". machine bolts, lock

washers, and hex nuts (not included). Bolts should be

of sufficient length to accommodate the saw base,

lock washers, hex nuts, and the thickness of the

workbench. Tighten all four bolts securely.

Carefully check the workbench after mounting to

make sure that no movement can occur during use.

If any tipping, sliding, or walking is noted, secure the

workbench to the floor before operating.

V. Assembly and adjustments (continued)

Mounting hole

Fig. 2

Fig. 3

Fig. 1

A A

Otros manuales para 055-6755-8

Tabla de contenidos

Otros manuales de Sierra de MasterCraft

MasterCraft

MasterCraft 054-8363-0 Manual de usuario

MasterCraft

MasterCraft 54-8333-2 Manual de usuario

MasterCraft

MasterCraft 054-8326-0 Manual de usuario

MasterCraft

MasterCraft 55-6847-0 Manual de usuario

MasterCraft

MasterCraft MAXIMUM 055-6768-8 Manual de usuario

MasterCraft

MasterCraft 054-8255-8 Manual de usuario

MasterCraft

MasterCraft 055-6778-4 Manual de usuario

MasterCraft

MasterCraft 54-8340-4 Manual de usuario

MasterCraft

MasterCraft 054-8161-0 Manual de usuario

MasterCraft

MasterCraft 055-6755-8 Manual de usuario

MasterCraft

MasterCraft 054-8332-4 Manual de usuario

MasterCraft

MasterCraft 054-8153-0 Manual de usuario

MasterCraft

MasterCraft 55-6883-2 Manual de usuario

MasterCraft

MasterCraft 054-8285-6 Manual de usuario

MasterCraft

MasterCraft 055-6742-8 Manual de usuario

MasterCraft

MasterCraft 55-6863-0 Manual de usuario

MasterCraft

MasterCraft Hawkeye Laser 054-8347-0 Manual de usuario

MasterCraft

MasterCraft 055-9035-4 Manual de usuario

MasterCraft

MasterCraft 055-6739-8 Manual de usuario

MasterCraft

MasterCraft 054-1237-4 Manual de usuario

MasterCraft

MasterCraft 55-6898-8 Manual de usuario

MasterCraft

MasterCraft 055-4500-6 Manual de usuario

MasterCraft

MasterCraft 055-6717-0 Manual de usuario

MasterCraft

MasterCraft 055-6740-2 Manual de usuario

Manuales populares de Sierra de otras marcas

RIDGID

RIDGID BS1400 Manual de usuario

ATIKA

ATIKA BWS 400-2 Manual de usuario

RGC

RGC FS20 Manual de usuario

Makita

Makita M2300 Manual de usuario

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manual de usuario

IMET Spa

IMET Spa SIRIO 370 AF-E Manual de usuario

Optimum

Optimum OPTisaw CS 275 Manual de usuario

Makita

Makita BPB180 Manual de usuario

Stihl

Stihl MS 462 C-M Manual de usuario

AEG

AEG TS 250 K Manual de usuario

Meec tools

Meec tools 004665 Manual de usuario

Makita

Makita LS1018L Manual de usuario

Ryobi

Ryobi RCS1400 Manual de usuario

DeWalt

DeWalt DCS391 Manual de usuario

Sealey

Sealey SA72 Manual de usuario

skilsaw

skilsaw SPT88 Instrucciones de montaje

Urrea

Urrea SI810 Dimensiones y guía de instalación

EINHELL

EINHELL BKG 210/1 Manual de usuario