Master View CS-12 Manual de usuario
User Manual
CS-12 / CS-12C
Read this guide thoroughly and follow the installation and operation proce-
dures carefully in order to prevent any damage to the units and/or any de-
vices that connect to them.
This package contains:
M1 Master View CS-12 KVM Switch
M2 CS Custom KVM Cables (CS-12C only)
M1 User Manual
If anything is damaged or missing, contact your dealer.
© Copyright 2003 ATEN®International Co., Ltd.
Manual Part No. PAPE-1143-300
Printed in Taiwan 06/2003
All brand names and trademarks are the registered property of their respective owners.
2003-11-18
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in
accordance with the instruction manual, may cause
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
MReorient or relocate the receiving antenna;
MIncrease the separation between the equipment and
receiver;
MConnect the equipment into an outlet on a circuit different
from that which the receiver is connected;
MConsult the dealer or an experienced radio/television
technician for help.
2003-11-18
Overview
The Master View CS-12 / CS-12C KVM (Keyboard, Video,
Mouse), Switch is a control unit that allows access to two
computers from a single console (keyboard, monitor, and
mouse). Before the development of the Master View, the only
way to control multiple computer configurations from a single
console was through a complex and costly network system.
Now, with the CS-12 / CS-12C, you can easily access two
computers in a cost effective manner.
The Master View CS-12 / CS-12C provides two convenient
methods to access the computers connected to the system:
using the push button Port Selection Switch located on the
unit’s side panel; and entering hotkey combinations from the
keyboard.
Setup is fast and easy; plugging cables into their appropriate
ports is all that is entailed. There is no software to configure, no
installation routines, and no incompatibility problems. Since the
CS-12 / CS-12C intercepts keyboard input directly, it works on
all hardware platforms and operating systems*.
There is no better way to save time and money than with a
Master View CS-12 / CS-12C installation. Since a single
console manages both of the computers, a CS-12 / CS-12C
setup: 1) eliminates the expense of having to purchase a
separate keyboard, monitor, and mouse for each computer; 2)
saves the space those extra components would take up; 3)
saves on energy costs; and 4) eliminates the inconvenience
and wasted effort involved in constantly moving around from
one computer to another.
*Mac and Sun systems may require additional equipment. See
p. 5 for details.
- 1 -
2003-11-18
Features
MOne console controls two computers
MEasy to install - no software required - connecting cables to
the computers is all it takes
MEasy to operate - computer selection via push button switch
or hotkeys
MAuto Scan function to monitor computer operation
MHot pluggable - add or remove computers for maintenance
without powering down the switch
MLED display for easy status monitoring
MCaps Lock, Num Lock, and Scroll Lock states are saved and
restored when switching
MKeyboard and mouse emulation for error free booting
MSupports Microsoft IntelliMouse and the scrolling wheel on
most mice
MSuperior video quality - up to 1920 x 1440; DDC2B
MCompatible with all operating platforms*
MNon-powered operation
MSaves time, space, power, and equipment costs
*Mac and Sun systems may require additional equipment. See
p. 5 for details.
- 2 -
2003-11-18
Hardware Requirements
Console
MA VGA, SVGA, or Multisync monitor capable of the highest
resolution that you will be using on any computer in the
installation.
MA PS/2 Style Mouse.
MA PS/2 Style Keyboard.
Computers
The following equipment must be installed on each computer
that is to be connected to the system:
MA VGA, SVGA or Multisync card.
MA PS/2 style keyboard port.
MA PS/2 style mouse port.
Cables
Although it is possible to use standard KVM cables to connect
the computers to the switch, for optimum signal integrity and to
simplify the layout, we strongly recommend that you use high
quality CS Custom KVM cables, like the ones provided as part
of the CS-12C package.
CS Custom KVM cable sets are available in 1.2, 1.8, 3, and 6
meter lengths (see table, below):
Length CS Part Number
1.2 m 2L-5201P
1.8 m 2L-5202P
3.0 m 2L-5203P
6.0 m 2L-5206P
To purchase cables, contact your dealer.
- 3 -
2003-11-18
Components
1. CPU Port A Connectors*
The KVM cables that connect to the keyboard, monitor, and
mouse ports of the computer you are designating as
Computer A plug in here. Each port is identified by an
appropriate icon.
2. Console Port Section
Your keyboard, monitor, and mouse cables plug in here.
Each port is identified by an appropriate icon.
- 4 -
4
4
5
1
2
3
2003-11-18
3. CPU Port B Connectors*
The KVM cables that connect to the keyboard, monitor, and
mouse ports of the computer you are designating as
Computer B plug in here. Each port is identified by an
appropriate icon.
4. LEDs
A lit LED indicates that its corresponding Port is the one that
has the KVM focus. Depending on the Port’s status, the LED
may flash according to a specific pattern (see the table on p.
11 for details).
5. Port Selection Switch
Pressing this push button switch toggles the KVM focus
between the computers.
*Since the KVM cables come with PS/2 style connectors, certain
hardware configurations (such as notebooks), that don’t have
two PS/2 ports may require the use of an adapter, as shown
below:
Adapter Purpose
UC-100KMATwo PS/2 ports to USB adapter for PCs,
Macs and Sun systems
If you require an adapter, contact your dealer.
- 5 -
2003-11-18
Installation
1. Plug the monitor, keyboard, and mouse into the Console
port connectors (located on the left side panel) of the switch.
2. Use KVM cables (as described in the Cables section, p. 4),
to connect the switch’s CPU A and CPU B ports (located on
the front and rear panel, respectively), to the keyboard,
monitor, and mouse ports of the computers you are installing.
Note: The Power On default is to link to the first computer
you turn on.
- 6 -
1. Make sure that power to all the devices you will be
connecting up have been turned off. You must
unplug the power cords of any computers that
have the Keyboard Power On function.
2. To prevent damage to your equipment, make sure
that all devices you will be connecting up are
properly grounded.
2003-11-18
Operation
Controlling both computers from a single console could not be
easier. Two port selection methods that provide instant access
to the computers are available:
MManual Port Selection
MHotkey Port Selection
Manual Port Selection
With Manual Port Selection, you simply press the Port
Selection button on the Master View’s side panel to toggle the
KVM access between the computers. The Selected LED on the
top panel lights to indicate which port has the focus.
Hotkey Port Selection
Hotkey port selection allows you to directly access a computer
from the keyboard, instead of having to manually switch to it
with the Port Selection button. The CS-12 / CS-12C provides
two hotkey port selection features:
MSelecting the Active Port
MAuto Scan Mode
- 7 -
2003-11-18
MSelecting the Active Port - Default Method:
The default method to toggle the KVM focus between the two
ports from the keyboard is to tap the left or right Ctrl key twice:
[Ctrl] [Ctrl]
Note: The combination must be on the same side (both Left, or
both Right).
MSelecting the Active Port - Alternate Method:
If the Ctrl key combination conflicts with programs running on
your computer, you can switch the hotkey to the Scroll Lock key
by pressing and holding the Port Selection button for three (3)
seconds. After this, tap the Scroll Lock key twice to toggle the
KVM focus.
[Scroll Lock] [Scroll Lock]
Note: To switch back to the default hotkey, press and hold the
Port Selection button for three (3) seconds again.
- 8 -
2003-11-18
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cambiar de Master View
Master View
Master View CS-1754 Manual de usuario
Master View
Master View CS-114A Manual de usuario
Master View
Master View CS-914 Manual de usuario
Master View
Master View CS-138D Manual de usuario
Master View
Master View CS-914 Manual de usuario
Master View
Master View CS-1804 Manual de usuario
Master View
Master View CS-1004 Manual de usuario
Master View
Master View CS-228 Manual de usuario
