Master Meter ELinx Manual de usuario

Master Meter, Inc. ❘101 Regency Parkway, Mansfield, TX 76063 ❘T: 817-842-8000 ❘MasterMeter.com

! !

eLinx™PROGRAMMING

Category: Registers & Endpoints

Type: eLinx Interpreter

Issue: Programming

eLinx Interpreter Programming Manual

Introduction

This document will walk you through how to properly program your eLinx™Interpreter®.

PLEASE NOTE: eLinx Technician Version 1.3.0 software should be used when programming.

Installation:

After installing eLinx Technician software (See Figure 1), plug in the eLinx Programmer (See

Figure 2) to your computer. After a few seconds the programmer will begin installing the

correct driver. You are now ready to being using eLinx Technician software.

Figure 1: eLinx Technician Software

eLinx Interpreter Programming Manual

Figure 2: eLinx Programmer

Communication Port:

Within the Unit Control menu located in the top left-hand corner of your screen, you will find

the Communication Port (COM Port) command (See Figure 3). Please ensure the correct

COM Port is selected for the eLinx Programmer. If the correct COM Port has not been

selected, you will need to manually locate this communication port within the Device Manager

menu of your computer.

Figure 3: COM Port

Read & Write:

The Read and Write tabs (See Figure 4), located within the Unit Control menu are the two

main tabs you will be using.

Figure 4: Read & Write Tabs

eLinx Interpreter Programming Manual

Programmability Fields:

The programmable design of eLinx Interpreter allows this register to work on most any meter

and connect to most any AMR/AMI system with common bayonet-style register housing.

Please use Figure 5below as a reference for the Programmability Fields section of this

document.

Figure 5: eLinx LCD Display

Below you find a list of fields to take note of (See Figure 6).

Figure 6: Programmability Fields

eLinx Interpreter Programming Manual

1. CW Read – Reading to be programmed (If new installation set to “0”)

2. Number of digit to show – Number of digits to be shown (One to nine digits)

3. Start From digit – Starting digit

4. Main Display Units – Reading range to be used (Four multiplier options available)

5. IR Rotation Flag – Direction the measuring chamber spins with water flow (CCW-

Normal (MM) is most commonly used for Master Meter water meters)

6. Meter Decimal Point – Decimal place value to be shown (Also known as the Unit of

Measure. See Figure 5)

7. Flow Decimal Point – Decimal place value to be shown in the Rate of Flow (Also the

unit of measure for water flow) window

8. Meter Gear-Ratio – Found in 3G Tech NET**

9. Flow Ratio – Gear ratio of the meter (Gallons or Cubic Feet)

PLEASE NOTE: In order to view Rate of Flow, the desired unit of measure must be entered in

the Meter Gear Ratio field (Gallons is the most common Unit of Measure used).

After all parameters have been selected, attach the eLinx Programmer to the eLinx

Interpreter. There are multiple ways to attach to eLinx. Please see connectivity options listed

below:

1. Sensus TR/PL Sensor w/Wire

2. Itron Inline Connector

3. Nicor Connector

4. Bare Wires

Once connected click on the Write tab, located in the Unit Control menu. You are now able

to program all parameters selected for your eLinx Interpreter. You can verify programming

parameters within the Programming Status window, located to the right of the eLinx

Information window (See Figure 7).

Figure 7: Programming Status

eLinx Interpreter Programming Manual

**To locate the Meter Gear-Ratio for your eLinx Interpreter follow the steps below within 3G

Tech NET:

1. Select the Interpreter box under the Select Unit Types menu.

2. Double-Click on Interpreter II Properties located in Set menu, directly to the right of

the Select Unit Types menu.

3. Select the correct Brand, Size (Diameter) and Model (Catalog) meter you are

installing. Once preferences have been selected the Gear Ratio will appear.

4. Enter this value within the Meter Gear-Ratio field of eLinx Tech to continue

programming your eLinx Interpreter.

Tabla de contenidos

Otros manuales de Instrumento de medición de Master Meter

Master Meter

Master Meter Register Hoja de instrucciones

Master Meter

Master Meter FAM Manual de usuario

Master Meter

Master Meter Madness PD Manual de usuario

Master Meter

Master Meter octave Manual de usuario

Master Meter

Master Meter Multi-Jet Manual de usuario

Master Meter

Master Meter Sonata Manual de usuario

Master Meter

Master Meter Allegro Pit Manual de usuario

Master Meter

Master Meter octave Manual de usuario

Master Meter

Master Meter Allegro Manual de usuario

Master Meter

Master Meter SONATA ALLEGRO Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario

Master Meter eLinx Manual de usuario

Manuales populares de Instrumento de medición de otras marcas