Master cool 89660 Manual de usuario

www.mastercool.com

OPERATING INSTRUCTIONS

PROFESSIONAL R134a MANIFOLD GAUGE SET

PART #89660

WARNING

Wear Safety Goggles

Avoid Contact with Refrigerant

R134a TEMPERATURE PRESSURE CHART

Ambient Temp (˚F) Low Side Gauge High Side Gauge

65˚ 25-35 psi 135-155 psi

70˚ 35-40 psi 145-160 psi

75˚ 35-45 psi 150-170 psi

80˚ 40-50 psi 175-210 psi

85˚ 45-55 psi 225-250 psi

90˚ 45-55 psi 250-270 psi

95˚ 50-55 psi 275-300 psi

100˚ 50-55 psi 315-325 psi

105˚ 50-55 psi 340-345 psi

TROUBLESHOOTING TIPS

• Low side and high side pressure are low.

Usually indicates a low charge.

• Low side pressure is low and high side pressure is high.

Usually indicates a blockage in the system. (i.e. expansion of valve or oriﬁce tube.)

• Low side pressure is high and high side pressure is low.

When accompanied by a vibrating gauge needle, usually indicates faulty reed valves in compressor.

• Low side and high side pressures are high.

Usually indicates an over charged system.

HOOK-UP FOR SYSTEM DIAGNOSIS:

• Verify that service ports are clean and free of metal shavings.

• Verify that both valves on the manifold are shut completely.

• Connect blue adapter to low side service port (5).

• Connect red adapter to high side service port (4).

• Start engine. Turn A/C mode selector to HIGH and fan to HIGH.

• Observe pressure on the manifold gauges and refer to your automotive manual for proper diagnosis.

CHARGING REFRIGERANT:

a. Verify that both valves on the manifold are shut completely.

www.mastercool.com

b. Turn on car and A/C system, (this will aid in charging of the refrigerant.)

c. Connect the other end of the yellow hose (3) to Refrigerant Gas supply. (Follow refrigerant manufacturer’s

instructions for proper dispensing.)

d. Open manifold low side (blue) valve slowly until pressure reaches 40 psi. Do not exceed 40 psi during the

recharging process. Exceeding 40 psi could damage the compressor.

e. When charging is ﬁnished, close low side (blue) valve.

EVACUATION OF SYSTEM WITH VACUUM PUMP AND LEAK TESTING:

a. Verify that there is no refrigerant in the A/C system.

b. Attached blue and red adapter to A/C system.

c. Connect yellow hose to vacuum pump, turn on pump.

d. Open manifold low side (blue) valve.

e. Open manifold high side (red) valve.

*After system had been evacuated to a gauge reading of 29” Hg (inches of vacuum), run vacuum pump for

20 minutes.

f. Close both high and low side manifold valves.

g. Allow system to sit and check gauges to verify vacuum remains.

SYSTEM SCHEMATIC:

1. Low side (blue) hose/adapter.

2. High side (red) hose/adapter.

3. Service (yellow) hose.

4. Compressor discharge service valve (16mm diameter.)

5. Compressor suction service valve (13mm diameter.)

89660-INST

Otros manuales de Instrumento de medición de Master cool

Master cool

Master cool 52233 Manual de usuario

Master cool

Master cool 98063-BT Manual de usuario

Master cool

Master cool 52238 Manual de usuario

Master cool

Master cool ULTIMA ID PRO 69HVAC -PRO2 Manual de usuario

Master cool

Master cool R134a Manual de usuario

Master cool

Master cool 52236 Manual de usuario

Master cool

Master cool 53100-C Manual de usuario

Master cool

Master cool Intella Sense 55800 Manual de usuario

Master cool

Master cool 98063-BT Manual de usuario

Master cool

Master cool R134a Manual de usuario

Master cool

Master cool Black Series Manual de usuario

Master cool

Master cool 98061 Manual de usuario

Master cool

Master cool R1234yf Manual de usuario

Master cool

Master cool 98061 Manual de usuario

Master cool

Master cool 52251 Manual de usuario

Master cool

Master cool 52240 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario