Mastech MS5908C Manual de usuario

MS5908C

Circuit Analyzer

User’s Manual

TEST

Hz%

L - N

L - E

N - E

Peak

Z - L

Z - N

Z - E

ASCC

5 A 8 A 10 A HOLD

NEL

V Vd Z

RCD

GFCI

[]

MS5908C

01 02

General Instructions

This circuit analyzer is a special test device

designed for AC low-voltage distribution line quick

fault location. With simple operation, accurate

measurement and other features, it can detect

multiple problems on a line, such as causing to

electric shock, electrical fire, abnormal operation

of equipment, etc.

Functions:

• TRMS measuring AC voltage

• Artificial load 5A, 8A, 10A measuring line drop

• Measuring phase voltage, neutral line (zero line)

voltage to earth, peak voltage, frequency

• Measuring phase (live line), neutral line (zero line),

earth line conductor impedance

• Identifying 3-wire socket connection mode (zero

for left and live for right, having earth line or not)

• Test the reliability of residual current device (RCD)

and response action time

• Test the reliability of GFCI action and response

action time

• Backlight function and data hold function

Warning

Do not use this instrument without reading,

understanding and following the instructions

in this manual. Read and follow them carefully,

as well as all warnings and instructions marked

on the instrument!

To prevent damages to the instrument, it should

not be used for measuring the output of UPS

equipment, nor for measuring adjustable light

and square wave generator!

For measurement accurency during repeated

usage, allow at least 30 seconds between two

consecutive measurements to facilitate

equipment cooling when measuring voltage

drop and cable impedance.

To ensure accurate measurement data, please

check whether there is important load or heavy

load in the line before testing. Turn off the heavy

load, if necessary, then retest.

05 06

L - N N - E Peak

Voltage (V ): real time display of cable connection

status and display the voltage drop of current load

and measurement results of phase voltage drop

TRMS. This test item includes 3 submenus, namely

load with 5A, 8A and 10A. Press Up “ ”or Down

“ ” selection key on the sub test item to enter the

relevant test item.

One analog load can be added to live line (phase

line) and zero line (neutral line) for the analyser

to measure the voltage drop, and then calculate the

voltage drop of 5A, 8A and 10A load separately.

Under the appropriate test function, press the test

key “ ” to test.

Menu Operation

The main test items of the analyser are located on

the bottom of display, including five test items,

namely: voltage (V), voltage drop (Vd),

impedance (Z), RCD and GFCI. Press the main test

item selection key “ ” to select relevant test item.

V Vd Z

RCD

GFCI

Voltage (V): real time display of TRMS of phase

voltage, wiring status and frequency. This test item

includes 3 submenus, namely phase voltage (L_N)

TRMS, voltage to earth of neutral line (zero line)

(N_E) TRMS, peak voltage (Peak). Press Up “ ”

or Down“ ” selection key on the sub test item to

enter the relevant test item.

Press “FUNC”Press “FUNC” Press “FUNC”

Press “FUNC”

Press“ ”

Press“ ” Press“ ”

Press“ ”

11 12

Wiring test

NEL

The wiring test result will be shown immediately

after the analyzer is plugged to the socket under

test. The analyzer can identify the following wiring

conditions and display the test result on the screen.

Wiring

condition

Normal

No ground

wire is found

The live/zero

line is

connected

inversely.

Other

conditions

Screen display

L E N Caption

Off

Flashing

Where any wiring abnormality is found, the

analyzer can only complete partial measurement.

Where there is no earth line, the analyzer can only

measure the phase voltage and voltage drop.

Notes: The analyzer can't detect

1. Circuit voltage, i.e. the voltage between two live

lines;

2. Combined fault;

3. Reverse connection of earth line and neutral line.

Voltage measurement

The normal measured value of phase voltage is

220V±10%, 50Hz. The peak voltage of sine-wave

alternating current is 1.414 times to the effective

value of phase voltage. The voltage to earth of

neutral line shall be less than 2V. In the single-phase

circuit, if the “voltage to earth of zero line” is high,

it indicates that the leakage current in zero line or

earth line is high. In the three-phase circuit with

neutral line, a high “voltage to earth of zero line”

indicates that the three-phase load is imbalanced

or the neutral line is affected by harmonic

interference. Excessive voltage (voltage to earth

of zero line) will result in running deviation or

interruption.

15 16

Voltage drop (V ) measurement

Dummy load shall be used in the circuit to

measure the load phase voltage and then calculate

the voltage drop. The voltage drop and load phase

voltage will be displayed when the load reaches

5A, 8A and 10A.

In terms of qualified circuit, when measurement

is made in the most remote socket from the

switchboard, the voltage drop shall be less than 5%.

During the measurement of the remaining sockets

of the same area, the farthest socket from the

switchboard shall be measured first and then other

measurements shall be made from the distant to

the near. The reading of the voltage drop shall be

shown on the downward trend.

If the voltage drop exceeds 5% and no obvious

drop of reading is found during the measurement

made near the switchboard, it indicates that the

first connection point goes wrong. In this case,

perform a visual inspection of the wire connection

among the first connection point, equipment and

switchboard and the connection of breaker

(air-break switch). Usually, a high impedance point

generates heat. To locate this problem, infrared

radiation thermometer can be used. In addition, we

can directly measure the voltage on both sides of

the breaker (air-break switch) to locate the point of

failure.

d If the voltage drop exceeds 5%, and during the

measurement made near the switchboard, the

reading drops constantly and no obvious change

is found between the two sockets, it indicates that

the lead wire diameter is too small compared with

the transmission distance, the transmission

distance is too long or the circuit is overloaded.

Under such circumstances, check the cable to see

if the lead wire diameter complies with the required

standard, and measure the lead wire current to see

if it is overloaded.

If the voltage drop exceeds 5% and there is an

obvious change of voltage drop reading between

the two sockets, it indicates that a high impedance

point exists between the two sockets. Usually,

problems are found at the contact, such as poor

connection, loose connector, or socket problem.

Tabla de contenidos

Otros manuales de Instrumento de medición de Mastech

Mastech

Mastech MS8340B Manual de usuario

Mastech

Mastech MS6700 Manual de usuario

Mastech

Mastech MS8239D Manual de usuario

Mastech

Mastech MS6580 Manual de usuario

Mastech

Mastech MS8238G Manual de usuario

Mastech

Mastech MS8240D Manual de usuario

Mastech

Mastech MS2001 Instrucciones de montaje

Mastech

Mastech MS2128A Manual de usuario

Mastech

Mastech MS2009A Manual de usuario

Mastech

Mastech M266F Instrucciones de montaje

Mastech

Mastech MS2301 Manual de usuario

Mastech

Mastech MS6900 Manual de usuario

Mastech

Mastech MS2030 Manual de usuario

Mastech

Mastech MS20006 Manual de usuario

Mastech

Mastech MS2108 Manual de usuario

Mastech

Mastech MS6252B Manual de usuario

Mastech

Mastech MS2115B Manual de usuario

Mastech

Mastech MS6503 Manual de usuario

Mastech

Mastech MS6701 Manual de usuario

Mastech

Mastech MS2001 Instrucciones de montaje

Mastech

Mastech MS2203 Manual de usuario

Mastech

Mastech MS2006B Manual de usuario

Mastech

Mastech MS8212A Manual de usuario

Mastech

Mastech MS2030A Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario