MARTINDALE 101 Manual de usuario

1375 Hird Ave., Cleveland, OH 44107 • Phone (216) 521-8567 • Fax Local 521-9476 / USA & Canada (800) 344-9191

E-Mail: [email protected] • Website: www.martindaleco.com

1375 Hird Ave., Cleveland, OH 44107 • Phone (216) 521-8567 • Fax Local 521-9476 / USA & Canada (800) 344-9191

E-Mail: [email protected] • Website: www.martindaleco.com

1375 Hird Ave., Cleveland, OH 44107 • Phone (216) 521-8567 • Fax Local 521-9476 / USA & Canada (800) 344-9191

E-Mail: [email protected] • Website: www.martindaleco.com

1. Remove 3 screws from back — install two D cell batteries.

2. Adjust probe spacing by loosening screws on terminal block and re-tightening (Caution: do not

over-tighten).

3. Rotate rheostat COMPLETELY to counter clockwise position—turn switch on. Failure to do this will

peg out needle, and cause the tester to no longer function, which will void your warranty.

4. Position probes on commutator bars; turn rheostat clockwise until meter hand indicates OK (Fig. 1).

5. Systematically check all commutator bars.

1375 Hird Ave., Cleveland, OH 44107 • Phone (216) 521-8567 • Fax Local 521-9476 / USA & Canada (800) 344-9191

E-Mail: [email protected] • Website: www.martindaleco.com

ONE YEAR LIMITED WARRANTY

This unit was thoroughly tested and in proper working order when

leaving the factory. It is warranted against defects in materials and work-

manship to the original purchaser for a period of one year from date of

sale.

During the warranty period, we will repair or replace at our option free

of charge to the original purchaser any part of the tester that our examina-

tion shows to be defective in workmanship or materials.

This warranty does not apply to damage in transit or damage caused

by misuse, abuse, neglect, accident, or alterations by unauthorized per-

sons.

Non-warrantable units will be repaired and returned C.O.D.

Note: Upon purchase, warranty card must be returned, or warranty

will be voided.

PO Box 430 Cleveland, OH 44107 • Phone (216) 521-8567 • Fax Local 521-9476 / USA & Canada (800) 344-9191

E-Mail: [email protected] • Website: www.martindaleco.com

BAR TO BAR TESTER MODEL 101

The only low cost tester that assures product stability. A simple check takes less than 30 seconds and

eliminates those troublesome comebacks and many dollars of additional expense.

Note: Be sure and read instructions in brochure that comes with your Bar to Bar Tester.

FEATURES:

I. The #101 will clearly show an open or partial open in the armature winding. Many times, solder

loosening, slung out, or damaged connections have occurred within the armature and are not visible

to the naked eye. Most often, growler testing will not show any of these faults. With a black or open

indication on the #101's meter, simply follow the red probe to the exact location of problem on the

armature. At this point the armature can be resoldered, saving a rewind replacement or costly war-

ranty.

II. The #101 will immediately pinpoint a reverse coil by indicating yellow or reverse on the meter.

III. The #101 quickly locates a short by pointing the red or short .

IV. The #101 will further show a good, re-usable armature by continually reading in the green or ok.

The Model #101 is the fastest, simplest, most time saving device of it’s kind. The test and results are

100% accurate. It offers at minimal cost both time and equipment savings, and quality that assures a

long and dependable life.

ADDITIONAL INSTRUCTIONS:

I. This meter will check any armature that has enough resistance to move the meter hand into the

green. On a large armature which has very little resistance the meter hand will move only slightly into

the green, which is alright, all we are looking for is a point to get a pattern all the way around the com-

mutator.

II. A dead short will keep the hand of the meter in the red. A partial short will not let the hand come

back to the red position, but will show a lower reading in the green from where you had your rheostat

set for a pattern to go by. This will show you where your problem is by following the red probe to the

lead in your armature coil.

III. If you use a growler on your armature and it shows shorted all the way around. It is very possible

that you have an armature with an equalizer. Be sure to use the Bar to Bar Tester and set your meter

PO Box 430 Cleveland, OH 44107 • Phone (216) 521-8567 • Fax Local 521-9476 / USA & Canada (800) 344-9191

E-Mail: [email protected] • Website: www.martindaleco.com

on “OK” or anywhere in the green. If you get the same pattern all the way around the commutator,

then your armature is OK. It should read like this - One High and Two Lows or Two Highs and One

Low, depending on how the equalizer is put in. If you have a short it will read in the red or read low

green. If you do not get the same pattern then the equalizer is shorted or coils in the armature are

shorted.

IV. For a unbalanced winding the armature should check good with a growler. To make sure the coils

are put in the armature correctly and connected correctly to the commutator use your Bar to Bar Tester

to check them. You should get the same pattern all the way around the commutator - For example: If

we have a 3 bundle coil with 1 turn and 2 with 2 turns - your pattern should read like this - 1 Low and

2 Highs and should repeat this pattern all the way around the commutator. If it does not have the same

pattern then the leads from the coil were set in the commutator wrong which will cause hot spots on

the armature and will not operate properly under a load.

V. In some cases we may check an armature that has so many turns of small wire that you will not

be able to move the rheostat. It will come up into the green just by turning the switch on. This is fine

as long as the meter hand doesn’t go out of the green, it will check the armature just the same as if

you were using the rheostat. If on a small tool armature the hand goes all the way past the green scale,

then this armature has too much resistance to check unless you change batteries and use some that

are very weak - For example - Batteries that will slightly light a flashlight bulb - As you can see by these

instructions the more resistance the more voltage the armature coils will build up.

VI. When the meter shows an open, first check for a loose connection, such as not soldered or tig

welded in the commutator properly. If that checks “OK” than look for a broken wire or lead.

Sometimes an armature will short causing an open and not show on the growler as a short.

VII. Reverse coil this happens mostly in a lap winding and when we are using a top connection. It

is easy to pick up a bottom lead for a top lead which will cause a reversed coil. This will not show on

a growler.

Tabla de contenidos

Otros manuales de Equipo de prueba de MARTINDALE

MARTINDALE

MARTINDALE PC104 Manual de usuario

MARTINDALE

MARTINDALE LTDV Manual de usuario

MARTINDALE

MARTINDALE E-ZeTest EZ2500 Manual de usuario

MARTINDALE

MARTINDALE PD240 Manual de usuario

MARTINDALE

MARTINDALE IN2101 Manual de usuario

MARTINDALE

MARTINDALE IN2101 Manual de usuario

MARTINDALE

MARTINDALE SPC70 Manual de usuario

MARTINDALE

MARTINDALE ET5 Manual de usuario

MARTINDALE

MARTINDALE IN2103 Manual de usuario

MARTINDALE

MARTINDALE VT25 Manual de usuario

MARTINDALE

MARTINDALE VT25 Manual de usuario

MARTINDALE

MARTINDALE PD690 Manual de usuario

MARTINDALE

MARTINDALE TEK402 Manual de usuario

MARTINDALE

MARTINDALE HPAT600 Manual de usuario

MARTINDALE

MARTINDALE RC2000 Manual de usuario

MARTINDALE

MARTINDALE IN2101 Manual de usuario

MARTINDALE

MARTINDALE ET4 Manual de usuario

MARTINDALE

MARTINDALE RC2000 Manual de usuario

MARTINDALE

MARTINDALE HANDYPAT HPAT400 Manual de usuario

MARTINDALE

MARTINDALE TEK 402 Manual de usuario

MARTINDALE

MARTINDALE EZ150:EZ650 Manual de usuario

MARTINDALE

MARTINDALE FD550 Manual de usuario

MARTINDALE

MARTINDALE MICROPAT+ Manual de usuario

MARTINDALE

MARTINDALE MTL10 Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario