Martin MAC 575 Krypton Manual de usuario
MAC 575 Krypton Low-Noise Upgrade Kit Installation Guide – Page 1 of 46
MAC 575 Krypton™ Low-Noise
Upgrade Kit Installation Guide
Introduction
This Installation Guide explains how to install the MAC 575 Krypton Low-Noise Upgrade Kit to convert a
standard MAC 575 Krypton to a Low-Noise model.
The MAC 575 Krypton Low-Noise Upgrade Kit has part number P/N 50300514.
For the latest documentation and information about this and all Martin Professional products, please visit
the Martin website at www.martin.com.
Warning! Read and follow the safety precautions in the MAC 575 Krypton user manual before installing the
Low-Noise Upgrade Kit. The user manual is supplied with the MAC 575 Krypton and is also
available for download from www.martin.com
Disconnect the fixture from power, allow to cool and place on a workbench before starting work.
The MAC 575 Krypton Low-Noise Upgrade Kit must be installed by qualified professional
technicians only. Read all of this Installation Guide carefully before starting to install the Upgrade
Kit. Martin Professional A/S and its affiliated companies cannot be held responsible for any
injury, damage, direct or indirect loss, consequential or economic loss or any other loss
resulting from failure to follow the instructions, respect the safety precautions and carry out the
safety tests listed in this Installation Guide.
If you have any questions about how to install the Upgrade Kit or use the MAC 575 Krypton
safely, please contact your local Martin distributor (see www.martin.com/distributors for details)
or call the Martin 24-hour service hotline on +45 8740 0000, or in the USA on 1-888-tech-180.
Important!To avoid damage to PCBs and their sensitive electronic components, take precautions to avoid
ESD (electrostatic discharge) and carry out work at an ESD-free workstation. Do not get oil or
grease onto optical components. If necessary, clean components with 99.9% isopropyl alcohol.
© 2008 Martin Professional A/S. Olof Palmes Allé 18, DK-8200 Aarhus N, Denmark. Information subject to change without notice. Martin
Professional A/S and all affiliated companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic
loss or any other loss occasioned by the use of, inability to use or reliance on the information contained in this installation note. The
Martin logo, the Martin name and all other trademarks in this document pertaining to services or products by Martin Professional A/S or its
affiliates and subsidiaries are trademarks owned or licensed by Martin Professional A/S or its affiliates or subsidiaries.
P/N 35000602 Rev. B
MAC 575 Krypton Low-Noise Upgrade Kit Installation Guide – Page 2 of 46
Overview
The MAC 575 Krypton Low-Noise Upgrade Kit contains the following items:
ABCD
EFGH
IJKL
MNOP
QRST
Table 1
MAC 575 Krypton Low-Noise Upgrade Kit Installation Guide – Page 3 of 46
Tools required
Screw sizes given in this guide are indicative only.
The following tools are normally required to upgrade a
standard MAC 575 Krypton as described in this guide.
However, if screws have been replaced during service, for
example, you may find that other tools are required.
• wire cutters
• adjustable wrench
• 4 mm Allen key
• 2 x flathead screwdrivers
• Pozidriv PZ1 and PZ2 screwdrivers (all cross-head screws in MAC 575 Krypton fixtures are Pozidriv,
not plain Phillips type)
• 10 mm and 8 mm hex head screwdrivers
• Torx TX10 and TX20 screwdrivers
• Round (needle) file
• Gaffa tape
• Spirit marker pen
To help you avoid dropping screws into the fixture, we recommend that you magnetize tools. Use of a
powered screwdriver with correctly set torque will also save you time.
UVWX
Y Z AA AB
Table 1
A Wiring harness P/N 11850227
B Wiring harness P/N 11850228
C SMPS to DC/DC PCB leads P/N 11850230
D High-voltage wiring diagram P/N 33120093
E Base shell with fans P/N 62408570
F SMPS bracket P/N 62408580
G Ballast mounting bracket P/N 62408370
H Ballast mounting plate P/N 62408440
I Ballast mounting plate, terminals side P/N 62408400
J Inrush PCB P/N 62408390
plus P/N 62000144
K Vented panel for ballast-side
base side cover P/N 23912582
L Pan stop with switch P/N 62400815
M Grounding label for ballast P/N 33160051
N Ballast label P/N 33160050
O Voltaflex insulation for base side cover P/N 33001113
P Voltaflex insulation for pan frame P/N 33001114
Q Flexible cable retainer P/N 13101010
R M6x70 hex ballast mounting bolts x3 P/N 08111007
S M6 lockwasher P/N 08114401
T M3 lockwasher P/N 08054401
U M3x6 countersunk Torx screw x4 P/N 08050802
V M4x12 countersunk Torx screw x10 P/N 08070808
W M3x8 panhead Torx screw P/N 08050703
X M4x16 panhead Torx self-tap screw x3 P/N 08070703
Y M6 washer, stainless steel x3 P/N 08114302
Z M3x8 countersunk Torx screw x2 P/N 08050803
AA M4x10 phd. Torx tap + spike screw x6 P/N 08070701
AB Spacer Ø7/Ø4 x2 P/N 08261020
Parts list
MAC 575 Krypton Low-Noise Upgrade Kit Installation Guide – Page 4 of 46
Schematic wiring diagram
MAC 575 Krypton Low-Noise Upgrade Kit Installation Guide – Page 5 of 46
Replacement of components
To install the MAC 575 Krypton Low-Noise Upgrade Kit components in a standard MAC 575 Krypton
fixture:
1. Disconnect the fixture from
power, allow to cool, and place
on a workbench. Take
precautions against ESD
(electro-static discharge).
2. See Figure 1. Lay the fixture
on its side and remove the 14
Torx 20 pan frame retaining
screws (arrowed),
P/N 08070808, from the base.
Keep the screws for re-use.
3. See Figure 2. Stand the fixture
upright.RemovethethreePZ2
screws from the corners of
each base top cover (6 screws
total P/N 08070502) but do not
remove the ground (earth)
lead Torx screws that are set
slightly in from the corners of
the base covers. Keep screws
for re-use during reassembly.
Figure 1
Figure 2
MAC 575 Krypton Low-Noise Upgrade Kit Installation Guide – Page 6 of 46
4. See Figure 3. Remove the four
PZ2 screws Afrom the base
side cover on the ballast side.
Keep the screws for re-use.
Cut cable ties Bas necessary
to release the wiring to the
SMPS module and move the
cover away from the base.
5. See Figure 4. Remove the two
PZ2 screws Cfrom the top of
the base side cover and lift the
cover away from the SMPS
module. The screws are no
longer required.
Figure 3
A
A
A
A
B
Figure 4
C
C
Figure 4
MAC 575 Krypton Low-Noise Upgrade Kit Installation Guide – Page 7 of 46
6. See Figure 5. Cut cable ties as
necessary to release the base
side cover’s ground lead.
7. See Figure 6. Remove the
Torx 20 ground lead screw
(arrowed) from the base side
cover and disconnect the
ground lead. Keep the screw,
washer and ground lead for
re-use.
8. See Figure 7. Remove the
two PZ2 screws at each side
of the base cover and
remove the cover inner
panel. Keep the screws for
re-use.Thecoverinner panel
is no longer required.
Figure 5
Figure 6
Figure 7
MAC 575 Krypton Low-Noise Upgrade Kit Installation Guide – Page 8 of 46
9. See Figure 8. A new inner
panel with air vents,
P/N 23912582, is supplied in
the Upgrade Kit. Turn the
inner panel so that the tab
(arrowed) in one edge of the
inner panel is lined up with
the channel in the base side
side cover. Use the two
screws you have just
removed to fasten the new
inner panel into the base side
cover. You are screwing into
plastic, so do not overtighten.
Put the side cover and inner
panel assembly to one side.
10. See Figure 9. Remove the
nut and lock washer from the
phase compensation
capacitor. Keep the nut and
washer for re-use.
11. See Figure 10. Disconnect
the spade connectors from
the phase compensation
capacitor and remove the
capacitor. Keep the capacitor
for re-use.
Figure 8
Figure 9
Figure 10
MAC 575 Krypton Low-Noise Upgrade Kit Installation Guide – Page 9 of 46
12. See Figure 11. Remove the
Torx 20 ground lead screw
(arrowed) from the end of the
SMPS (switch-mode power
supply). The screw, washer
and ground lead are no
longer required.
13. See Figure 12. Note which
terminals the voltage Aand
frequency Btap leads on the
ballast are connected to and
use a small flathead
screwdriver to release the
tap leads from the terminals.
14. See Figure 13. Remove the
four Torx 10 screws from the
inrush PCB mounting posts,
using a wrench to hold the
mounting posts while you
loosen the screws. The
screws are no longer
required.
Figure 11
Figure 12
AB
Figure 13
MAC 575 Krypton Low-Noise Upgrade Kit Installation Guide – Page 10 of 46
15. See Figure 14. Remove the
four Torx 10 screws
(arrowed, one screw is
hidden behind the
technician’s hand in the
photo) from the DC/DC PCB
mounting posts. These
screws are no longer
required. Move the DC/DC
PCB to one side for access
to the SMPS mounting
screws.
16. See Figure 15. Remove the
three Torx 10 SMPS
mounting screws (arrowed)
from the SMPS bracket.
Keep the screws for re-use.
Figure 14
Figure 15
Otros manuales para MAC 575 Krypton
2
Tabla de contenidos
Otros manuales de Equipo de DJ de Martin
Martin
Martin MAC 600 Manual de usuario
Martin
Martin MAC 700 WASH Manual de usuario
Martin
Martin Atomic 3000 LED Manual de usuario
Martin
Martin Exterior Inground 400 Manual de usuario
Martin
Martin THRILL Compact PAR 64 LED Manual de usuario
Martin
Martin PixLine 10 Manual de usuario
Martin
Martin MAC Aura XB Manual de usuario
Martin
Martin MX-10 Manual de usuario
Martin
Martin MAC Encore Performance CLD Guía de configuración
Martin
Martin MAC Quantum Profile Manual de usuario
Martin
Martin ELP WW Manual de usuario
Martin
Martin Mania EF1i Manual de usuario
Martin
Martin MAC Allure Wash PC Manual de usuario
Martin
Martin MAC 2000 Wash XB Manual de usuario
Martin
Martin JEM Glaciator X-Stream Manual de usuario
Martin
Martin THRILL Manual de usuario
Martin
Martin T-Rex Manual de usuario
Martin
Martin MAC 2000 Profile II Manual
Martin
Martin RUSH MH 10 Beam FX Manual de usuario
Martin
Martin RUSH PAR 3 RGB Manual de usuario
Manuales populares de Equipo de DJ de otras marcas
thomann
thomann Stairville DJ Lase 40-G MK-III Manual de usuario
Eagletone
Eagletone 6 Eyes Flower Manual de usuario
EuroLite
EuroLite FLD-1508 Manual de usuario
Technical Pro
Technical Pro LG8xSEA Manual de usuario
JB Systems
JB Systems Lounge Laser DMX Manual de usuario
Lightmaxx
Lightmaxx Vega Halo 90 Manual de usuario
Elation
Elation FUZE WASH Z350 Manual de usuario
Maverick
Maverick MK3 WASH Manual de usuario
Infinity
Infinity TF-260C7 Fresnel Manual de usuario
Chauvet
Chauvet EVE E-50Z Manual de usuario
Eliminator Lighting
Eliminator Lighting E 138 Manual de usuario
EuroLite
EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario