Marshall Amplification V-MD241 Manual de usuario

MarshallElectronics

,Inc.

1910 East Maple Ave.

El Segundo, CA 90245

Tel: (800) 800-6608 / (310) 333-0606 • Fax: 310-333-0688

www.LCDRacks.com •sales@lcdracks.com

MarshallElectronics

Model No. V-MD241

High Definition LCD Monitor with Modular Inputs

Operating Instructions

Edition 2 Revision 0P

This page intentionally left blank

Maintenance

■Screen Cleaning

Periodically clean the screen surface using ammonia-free cleaning wipes (Marshall Part No. V-HWP-K). A clean micro-fiber cloth

can also be used using only non-abrasive and ammonia-free cleaning agents. Do not use paper towels. Paper towel fibers are

coarse and may scratch the surface of the polycarbonate faceplate or leave streaks on the surface. Antistatic and fingerprint

resistant cleaning agents are recommended. Do not apply excessive pressure to the screen to avoid damaging the LCD.

■Faceplate Dusting

Dust the unit with a soft, damp cloth or chamois. Dry or abrasive cloths may cause electrostatic charge on the surface, attracting

dust particles. Neutralize static electricity effects by using the recommended cleaning and polishing practice.

Warranty

Marshall Electronics warranties to the first consumer that this V-MD241 LCD monitor will, under normal use, be free from

defects in workmanship and materials, when received in its original container, for a period of one year from the purchase date.

This warranty is extended to the first consumer only, and proof of purchase is necessary to honor the warranty. If there is no

proof of purchase provided with a warranty claim, Marshall Electronics reserves the right not to honor the warranty set forth

above. Therefore, labor and parts may be charged to the consumer. This warranty does not apply to the product exterior or

cosmetics. Misuse, abnormal handling, alterations or modifications in design or construction void this warranty. It is considered

normal for a minimal amount of pixels, not to exceed three, to fail on the periphery of the display active viewing area. Marshall

Electronics reserves the option to refuse service for display pixel failure if deemed unobtrusive to effective use of the monitor by

our technicians. No sales personnel of the seller or any other person is authorized to make any warranties other than those

described above, or to extend the duration of any warranties on behalf of Marshall Electronics, beyond the time period

described above. Due to constant effort to improve products and product features, specifications may change without notice.

This page intentionally left blank

Table of Contents

Installation and Initial Setup ------------------------------------------------------------------------------------------------------5

Top and Front Panel Features ----------------------------------------------------------------------------------------------------7

Rear Panel Features-----------------------------------------------------------------------------------------------------------------8

Compatible Input Formats---------------------------------------------------------------------------------------------------------9

Input Module Installation-------------------------------------------------------------------------------------------------------- 10

MAIN MENU AND NAVIGATION------------------------------------------------------------------------------------------------ 11

VIDEO CONFIGURATION SUBMENU ....................................................................................................................................................11

MARKER CONFIGURATION SUBMENU ................................................................................................................................................14

FILTER CONFIGURATION SUBMENU....................................................................................................................................................17

SYSTEM CONFIGURATION SUBMENU .................................................................................................................................................19

FUNCTION PRESETS SUBMENU ........................................................................................................................................................... 20

IMD & TALLY CONFIGURATION ...........................................................................................................................................................20

SYSTEM INFORMATION SUBMENU ..................................................................................................................................................... 22

NETWORK CONFIGURATION SUBMENU .............................................................................................................................................22

Network Control Page ------------------------------------------------------------------------------------------------------------ 24

Power Tab ...........................................................................................................................................................................................24

Menu Tab ............................................................................................................................................................................................24

Function Presets..................................................................................................................................................................................26

IMD / Tally Config................................................................................................................................................................................26

Display Tab ..........................................................................................................................................................................................27

Keypad Tab..........................................................................................................................................................................................27

Tally Tab ..............................................................................................................................................................................................27

Network Tab........................................................................................................................................................................................27

Network Configuration........................................................................................................................................................................27

Navigator.............................................................................................................................................................................................28

Info Tab ...............................................................................................................................................................................................29

Global -------------------------------------------------------------------------------------------------------------------------------- 30

Specifications----------------------------------------------------------------------------------------------------------------------- 31

Dimensions-------------------------------------------------------------------------------------------------------------------------- 32

Maintenance------------------------------------------------------------------------------------------------------------------------ 35

Warranty ---------------------------------------------------------------------------------------------------------------------------- 35

This page intentionally left blank

Warning: Please use only the square type VESA mount (which fits inside the VESA Screw Length WARNING

silkscreen) with the 75mm hole pattern in order to avoid obstructing Module Slot 2.

Dimensions

Installation and Initial Setup

■Unpacking

Carefully unpack the V-MD241 monitor and verify that the following items are included:

• V-MD241 Monitor

• V-PS12-5A-XLR Power Supply

• Operating Instructions

Inspect the unit for any physical damage that may have occurred during shipping. Should there be any damage, immediately

contact Marshall Electronics at (800) 800-6608. If you are not located within the continental United States, call +1 (310) 333-

0606.

■Installation

A VESA standard 200/75mm hole pattern also allows custom mounting installations. Alternately, the V-MD241 can be used in a

desktop configuration with optional stand. Please contact Marshall Electronics for more information.

Warning: Please use only the square type VESA mount (which fits inside the VESA Screw Length WARNING

silkscreen) with the 200/75mm hole pattern in order to avoid obstructing Module Slot 2.

Please contact Marshall Electronics or visit www.LCDRACKS.com for further information.

■Connections, Power-On and Initial Setup

Plug the power supply into an AC power source (100-240 V @ 50/60 Hz). Attach the Power connector to the back of the monitor.

Connect the required cables for video signal input and output. (Power must be applied to the V-MD241 for the active loop-

though output to be activated.) The monitor defaults to ‘ON’ when power is supplied. Video will automatically be detected and

displayed on the screen.

This page intentionally left blank

Specifications

■PANEL

Screen Size 24” Diagonal

Display Area (h x v) 531.36 x 298.89 mm

Pixels 1920 x RGB x 1080

Viewing Angle (h x v) 178° x 178°

Brightness 300 cd/m2

Contrast Ratio 3000:1

■VIDEO INPUT/OUTPUT

Video Input / Output (Composite)

Supports SMPTE 170M, NTSC/PAL

YPBPRInput / Output (Component)

Supports SMPTE 260M, 274M, 296M

■CONNECTORS

Video Input

Video (Composite) 1 x BNC Female (75 Ω)

YPBPR(Component) 3 x BNC Female (75 Ω)

Video Output (Active Loop-Through)

Video (Composite) 1 x BNC Female (75 Ω)

YPBPR(Component) 3 x BNC Female (75 Ω)

S1, S2 (Module Slots)

For Marshall I/O Modules Only

Cold-Swap – remove power from unit before

Inserting or removing Modules.

Power Input

4-Pin XLR Connector

Tally Hardware Interface

HD-15 Female

CN-1 – Programming Port*

Factory / Upgrade Use Only

■TALLY Hardware Interface (HD-15)

Activation requires contact closure of pin to ground

on the HD-15 connector:

■ELECTRICAL

Power Consumption 3.5A @ 12VDC (42 W)

Voltage Requirement 12 VDC

■MECHANICAL

Weight (with rack ears): 11.05 lbs

Operating Temperature 32°F to 104°F (0°C to 40°C)

Storage Temperature -4°F to120°F (-20°C to

50°C)

See Dimensions section for exact specifications.

Warning: Please use only the square type VESA

mount (which fits inside the VESA Screw Length

WARNING silkscreen) with the 75mm hole pattern in

order to avoid obstructing Module Slot 2.

. HD-15 Female

Ethernet Control Interface

RJ-45 6p6c Female Connector

Global

Use the Global tab to control multiple Marshall Electronics MD monitors simultaneously. Only the POWER, MENU and DISPLAY

tabs may be used on the GLOBAL scale. All other options must be used on an individual monitor basis.

To control monitors globally:

1) Click on the GLOBAL CONTROL tab on the bottom of the web page. This will display the GLOBAL CONTROL menu.

2) Press the SCAN NETWORK button at the bottom of the GLOBAL CONTROL menu. This will scan your network for any

other MD series monitors and list them under SELECT MONITORS TO CONTROL list.

3) Click on all monitors that you wish to control with the GLOBAL CONTROL settings.

4) Click on the POWER, MENU or DISPLAY buttons that you wish to control.

Scan Network

Use the Scan Network button to scan for any other Marshall Electronics MD monitor connected on your network. The results

will show up in the SELECT MONITORS TO CONTROL box.

SELECT MONITORS TO CONTROL box

This box will list any MD Series monitors found on your network. The box will list the following items about each monitor: Host

Name, IP Address, Model. The IDENTIFY section allows you to identify a particular monitor by toggling all 3 Tally LEDs at once.

Use this to determine which physical monitor you will be controlling.

Monitor Count

Use this count to quickly identify the number of Marshall Electronics MD monitors on your network.

Top and Front Panel Features

Power Button

Use the power button to toggle between ON and STANDBY

modes. In both the STANDBY and the ON state, the LED on

the button will illuminate bright green. This indicates that

MAIN power is applied to the unit.

Input Select Buttons

Use the VIDEO, YPbPr, S1 and S2 buttons to select the

corresponding analog or digital input. Video standards

(NTSC/PAL, etc.) are automatically detected. S1 and S2

buttons select inputs connected to Optional Input Modules

(located in Slot-1 or Slot-2).

User-Definable Function Buttons

Four user-definable function buttons can be used for direct

access to various settings. Functions are assigned using the on-

screen menu.

Menu Navigation Buttons

Use the Menu, ▲,▼, and Select buttons to display and

navigate the on-screen menu (See Main Menu and

Navigation).

Image Adjustment Knobs

Use the image adjustment knobs to adjust color brightness,

color-saturation, tint, and contrast of the image. The status of

each image adjustment parameter is shown on the bottom left

of the screen, with values ranging from 0 to 100. Default value

is 50.

LED Tally

Three LED tally lights (yellow, red, green) are available above

the screen.

Rear Panel Features

YPbPr and CVBS Video Input and Output

The V-MD241 has CVBS and YPbPr inputs and one active loop-

through output for each input. See Compatible Input Formats

for details on accepted formats.

Power Input

Connect 12VDC to the 4-pin XLR power input connector.

Power should only be supplied from the included power

supply.

IMPORTANT: If using a power source other than the included

power supply, damage may result. Please use the pin out

diagram in the Specifications section.

Tally Input Connector

The LED tally can be activated via the HD-15 connector by

connecting the corresponding pin to ground. A variety of

external devices can be used to perform the contact closure.

No additional power should be supplied to the HD-15 port.

Network Port

The Network Port is used to access the Network Control Page

for the V-MD monitor. Use a regular RJ45 Ethernet cable to

connect the V-MD monitor to your network. Please see the

Network Configuration Submenu section of this manual for

further connection details.

Desktop Mounting Holes

These holes are used when attaching the monitor to the

optional desktop stand.

VESA 200/75mm Hole Pattern

VESA-standard 200/75 mm hole-patterns is provided to

accommodate a variety of custom mounting options. See

Dimensions for further details.

Warning: Please use only the square type VESA mount (which

fits inside the VESA Screw Length WARNING silkscreen) with

the 200/75mm hole pattern in order to avoid obstructing

Module Slot 2.

Optional Module Slot 1 / Slot 2

The V-MD monitor comes with Module Slots for Marshall

Electronics’ line of future proof Input Modules. Please contact

Marshall Electronics for a list of compatible Input Modules.

See the Input Module Installation instructions for details on

Module installation.

PROG Port

The PROG port is a Service / Upgrade port only. Please

contact Marshall Electronics for more information.

The Network Control page’s Navigator allows you to scan your network for any other Marshall Electronics Web Enabled MD

monitors. From the navigator, you can find and sort all monitors by their Host Name, IP Address or Model number. You can also

access each monitor’s Network Control page.

Press the Scan Network button once to scan your network for other MD monitors. The navigator will not detect any monitors

added to the network if the scan was performed prior to their installation.

The information field at the bottom will indicate the Host Name, IP Address and model number of the origin of the Navigator pop

up page. It will also give a count of how many monitors have been found on the network.

Info Tab

■System

This shows the System firmware version of your monitor.

■Power Module

This shows the Power Module firmware version of your monitor.

■Keypad

This shows the Keypad firmware version if your monitor has a Keypad separate from the main system board.

■Slot

This field determines the type of module present on the system as well as its firmware version. If there is no module

installed, the text will read “No Module v0.00.”

■Remote Enable

Select whether you would like to be able to access a particular monitor’s web page or web functions from another monitor on

the same network or only through the current monitor’s web page.

■Configuration Mode

Use this drop down menu to select between the different IP configuration modes available for the monitor.

■IP Address

If you have selected the Manual configuration mode for the IP configuration mode, you will be able to enter an IP address

manually in this field. If you have selected DHCP, the box will have an IP address already entered. This cannot be modified

when in DHCP mode.

■Subnet Mask

If you have selected the Manual configuration mode for the IP configuration mode, you will be able to enter Subnet Mask

address manually in this field. If you have selected DHCP, the box will have Subnet Mask already entered. This cannot be

modified when in DHCP mode.

■Default Gateway

If you have selected the Manual configuration mode for the IP configuration mode, you will be able to enter Default Gateway

address manually in this field. If you have selected DHCP, the box will have Default Gateway already entered. This cannot be

modified when in DHCP mode.

■Host Name

Use this field to enter a Host Name for the monitor. You may choose up to 15 alphanumeric characters for the Host Name.

■Web Authentication

Fill in the Web Authentication box to protect the monitor from being accessed by a user without a User Name and Password.

Filling this box in will enable the Username and Password fields below.

■Username

Enter a 15 alphanumeric character string Username in this field. This will only work if the Web Authentication option

has been turned ON.

■Enter Password / Re-enter Password

Enter a 15 alphanumeric character string Password in this field. You will need to Re-enter the password in the box

below the Enter Password box for additional security.

■MAC Address

This is the unique MAC address for this monitor. This cannot be changed.

To save all changes, press the Apply Changes button. You may also cancel out of the changes you have made by pressing the

Cancel button.

Navigator

Compatible Input Formats

The following video standards are supported by the V-MD241:

Video Input

NTSC, PAL

YPbPr Input

480i, 576i/50

480p, 576p/50

720p/25, 29.97, 30, 50, 59.94, 60

1080p/23.98, 23.98sF, 24, 24sF

1080i/50, 59.94, 60

Optional Input Modules (Type A modules)

MD-3GSDI and MD-TC – 3G/HD/SDI Input Module with Loop-Through

525i, 625i/50

720p/25, 29.97, 30, 50, 59.94, 60

1080p/23.98, 23.98sF, 24, 24sF, 25, 29, 30

1080i/50, 59.94, 60

3G – Level A and Level B

YCbCr, YCbCr+A, RGB, RGB+A

1080p/ 60, 59.94, 50

1080p/ 30, 29.97, 25, 24, 23.98, 30sF, 29.97sF, 25sF, 24sF, 23.98sF

1080i/ 60, 59.94, 50

MD-HDSDIx2 – Two-channel HD-SDI Input Module with switched output

525i, 625i/50

720p/25, 29.97, 30, 50, 59.94, 60

1080p/23.98, 23.98sF, 24, 24sF, 25, 29, 30

1080i/50, 59.94, 60

MD-HDMIx2 – Two-channel HDMI Input Module

480p59.94, 576p/50

720p/25, 29.97, 30, 50, 59.94, 60

1080p/23.98, 23.98sF, 24, 24sF, 25, 29, 30

1080i/50, 59.94, 60

MD-DVII – DVI-I Input Module

640 x 480/ 60, 75, 85

800 x 600/ 60, 75, 85

1024 x 768/ 60, 75, 85

1280 x 1024/ 60, 75

1600 x 1200/ 60 (CVT Timing)

1920 x 1200/ 60 (CVT Timing)

Input Module Installation

1. Remove Power From Unit

Modules are cold-swappable only. Damage will occur if modules are inserted or removed while unit is

powered.

2. Remove Blank Module Cover

Using Philips screwdriver, remove the 4-40x1/8” screws. There are a total of three screws, save them for later

use.

Remove blank cover

3. Insert Optional Module

Decide which slot you intend to install module (Slot 1 or Slot 2)

Carefully align the module with the chosen slot. The raised rails will fit inside the module

Align the Module so that the three (3) mounting holes all line up with the threaded holes of the slot.

The connectors on both the module and the main-board slot should now be in alignment.

Carefully PRESS the module into the slot. Module will seat flush with the rear of the unit.

Replace the three (3) screws removed in Step 2.

*NOTE* Use ONLY 4-40x1/8” screws provided. Any screw longer than 1/8” will damage the main unit.

■On-Screen Tally

Use this to turn the On-Screen Tally lights ON or OFF.

■Text Tally

Use this to turn the Text Tally function ON or OFF.

Display Tab

Image Adjust

■BRIGHTNESS, COLOR, CONTRAST

Use this section to adjust the Brightness, Color and Contrast of each individual panel. To enter a value manually, type in a

number from 0-100 in the dialogue box and press Set. The value selected on this page will show up on the monitor screen in

real time.

RGB Gain / Bias

■RGB Gain and Bias

Use this section to adjust the Gain and Bias for the Red, Green and Blue components of the video signal. To enter a value

manually, type in a number from 0-100 in the dialogue box and press Set.

Backlight

■Backlight

Use this section to adjust the Backlight value for the monitor. To enter a value manually, type in a number from 0-100 in the

dialogue box and press Set.

Keypad Tab

Keypad

Use the keypad portion of the Network Control page to access all aspects of the physical keypad from the Network Control page.

Tally Tab

Tally

Use the Tally page, in conjunction with the LAN100 tally source, to control the LED and soft tally on the monitor.

The radio buttons allow for customization of tally lights to be used by the monitor.

Network Tab

Network Configuration

Tabla de contenidos

Otros manuales de Monitor de Marshall Amplification

Marshall Amplification

Marshall Amplification 7" TFT LCD Color Monitor V-ASL7070 Manual de usuario

Marshall Amplification

Marshall Amplification Monitor V-LCD4-PRO-L Manual de usuario

Marshall Amplification

Marshall Amplification M-Lynx-10W Manual de usuario

Marshall Amplification

Marshall Amplification M-LYNX-702 Manual de usuario

Marshall Amplification

Marshall Amplification V-LCD51 Manual de usuario

Marshall Amplification

Marshall Amplification V-R201-IMD-TE Manual de usuario

Marshall Amplification

Marshall Amplification V-R171P Manual de usuario

Marshall Amplification

Marshall Amplification V-R563P-SDI Manual de usuario

Marshall Amplification

Marshall Amplification V-702W Manual de usuario

Marshall Amplification

Marshall Amplification V-R201-IMD-TE Manual de usuario

Marshall Amplification

Marshall Amplification V-R84P-SDI Manual de usuario

Marshall Amplification

Marshall Amplification V-R154P Manual de usuario

Marshall Amplification

Marshall Amplification ML-454-V2 Manual de usuario

Marshall Amplification

Marshall Amplification ML-503 Manual de usuario

Marshall Amplification

Marshall Amplification V-R171X-DLW Manual de usuario

Marshall Amplification

Marshall Amplification V-R231P-AFHD Manual de usuario

Marshall Amplification

Marshall Amplification V-RD151P Manual de usuario

Marshall Amplification

Marshall Amplification V-R841P-AFHD Manual de usuario

Marshall Amplification

Marshall Amplification ML-454 Manual de usuario

Marshall Amplification

Marshall Amplification V-R241-4K Manual de usuario

Marshall Amplification

Marshall Amplification V-R191P-SDI Manual de usuario

Marshall Amplification

Marshall Amplification V-R1041DP-AFHD Manual de usuario

Marshall Amplification

Marshall Amplification V-R171P-AFHD Manual de usuario

Marshall Amplification

Marshall Amplification V-R70DP Manual de usuario

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación