Marsh 241D Manual de usuario

1. Remove current hot date coder

1.1 Stop the line, power o the hot date

coder.

If using air-driven hot date coder, shut

o air supply and disconnect air pipe.

1.2 Remove packaging material from

the coder bracket area.

1.4 Using wider end of Allen key a

from Marsh 241D box, remove the

2 bracket mounting screws.

1.5 Remove the bracket locking handle. 1.6 Remove existing platen rubber

from bracket, along with any platen

rubber clamps.

1.3 Undo connector on hot date coder.

Marsh 241D Installation Guide

3. Fix Marsh 241D to the correct print position

2. Fit Marsh 241D to bracket

3.1 Undo the 2 screws ½ turn. 3.2 Using smaller end of the supplied

Allen key a, loosen the gap

adjustment screw 1 full turn.

2.1 Fit new Marsh adhesive backed

platen rubber b in place of old

platen rubber.

2.2 Fit Marsh 241D to bracket clamp

using the 2 new mounting screws c

from the Marsh 241D box. Tighten

the 2 screws.

3.3 Push the printer towards the platen

rubber b to make sure the gap setting

tool dis pressing against, and in square

alignment with, the platen rubber.

3.4 Hold the printer rmly to keep in

this position and then tighten the

gap adjustment screw.

3.7 Push printhead carriage away to

unclip from the gap setting tool d.

Pull out the gap setting tool and

keep safe.

3.9a If it DOES slide, then re-t the

bracket locking handle.

3.5 Continue to hold the printer rmly

to keep in this position. Tighten both

bracket mounting screws c .

3.8 Wind on the ribbon by hand to

ensure it is tight.

3.9b If it does NOT slide, the bracket

locking handle is not needed. Unscrew

the top mounting screw ½ turn ONLY,

slide printer into desired position and

re-tighten the top mounting screw.

3.6 IMPORTANT: Check the gap setting

tool dhas remained in contact with,

and is square to, the platen rubber b .

3.9 Push on bracket clamp to see if it is

free to slide along the bracket slide bar.

3.10 Re-thread the packaging material

in the host machine.

4. Connect Marsh 241D

4.1 Unpack Marsh 241D I/O extension

cable eand t to Marsh 241D.

4.4 Unplug mains connector and

remaining connector from the hot date

coder control box. Remove the hot date

coder control box.

4.7 Using either the existing mains

IEC cable or the mains IEC cable f

supplied with the Marsh 241D,

connect mains power to the

power supply unit f.

4.2 Now focus on the hot date coder

control box, sitting on top of the VFFS

control cabinet. Unplug I/O connector

from the hot date coder control box.

4.5 Unpack Marsh 241D power

supply unit fand place it in place

of the hot date coder control box.

4.8 The Marsh 241D will power up with

a ashing light sequence and it will

wind a small amount of ribbon.

4.3 Connect I/O connector to

the I/O extension cable e.

4.6 Connect the 24VDC cable from the

Marsh 241D power supply unit fto

the Marsh 241D printer.

The Marsh 241D is

now ready to print

Otros manuales de Equipos para césped y jardín de Marsh

Marsh

Marsh Rain Cell Manual de usuario

Manuales populares de Equipos para césped y jardín de otras marcas

Vertex

Vertex 1/3 HP Especificaciones técnicas

GHE

GHE AeroFlo 80 Manual de usuario

Millcreek

Millcreek 406 Manual de usuario

Land Pride

Land Pride Post Hole Diggers HD25 Manual de usuario

extraspace

extraspace GardenStore Manual de usuario

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Manual de programación

Premier designs

Premier designs WindGarden 26829 Manual de usuario

Snapper

Snapper 1691351 Manual de usuario

Mosquito Magnet

Mosquito Magnet Patriot Manual de usuario

Perfect

Perfect BG2 Manual de usuario

P.Lindberg

P.Lindberg LS2 Manual de usuario

Gardena

Gardena Easy 1887 Manual de usuario

Makita

Makita UM104D Manual de usuario

AQUA FLOW

AQUA FLOW PNRAD Manual de usuario

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Guía del usuario

BIOGROD

BIOGROD 730710 Manual de usuario

Land Pride

Land Pride RCF2784 Manual de usuario

Makita

Makita UM110D Manual de usuario