Marmitek IP EYE ANYWHERE 10 - ADVANCED Manual de usuario
0
IP Eye Anywhere ™ IP RoboCam ™ 1
1PREFACE
Thank you for purchasing the Marmitek Wireless* Pan-Tilt**
MPEG4/MJPEG*** Network Camera, a powerful dual-codec***
wireless* network camera with the 1-way**** or 2-way***** audio
function that provides the high-quality image and on-the-spot audio
via the Internet connection. The Infrared LEDs and light sensor
*****enable the camera to capture images even in the dark
environment. The camera’s pan/tilt** functions allow you to control
the camera to monitor everywhere remotely. Through the GPIO**
connectors, the camera can attach a variety of external devices for
your specific purposes. The camera can be installed as a standalone
system within your application environment easily and quickly, and
supports remote management function so that you can access and
control it using a Web browser on your PC.
Not all cameras have all the options installed. Options are marked
with one or more * and have the following definition:
*IP Eye AnyWhere 11, 21, IP RoboCam 11, 21
** IP RoboCam 10, 11, 21
***IP Eye AnyWhere 20, 21 IP RoboCam 21
**** IP Eye AnyWhere 20, 21
*****IP Robocam 21
******IP Eye AnyWhere 10, 11, IP RoboCam 10, 11
This Advanced Installation Guide provides you with the instructions
and illustrations on how to use your camera, which includes:
Chapter 1 Introduction to Your Camera describes the
features of the camera. You will also know the components and
functions of the camera.
Chapter 2 Hardware Installation helps you install the camera
according to your application environment. You can use
this camera at home, at work, at any where you want.
©MARMITEK
2
Chapter 3 Accessing the Camera lets you start using your
camera without problem. The camera can be set up
easily and work within your network environment
instantly.
Chapter 4 Configuring the Camera guides you through the
configuration of the camera using the Web browser on
your PC.
Chapter 5 Appendix provides the specification of the camera and
some useful information for using your camera.
NOTE The illustrations and configuration values in this guide are for
reference only. The actual settings depend on your practical
application of the camera.
IP Eye Anywhere ™ IP RoboCam ™ 3
2CONTENTS
0................................................................................ 0
1Preface ..................................................................... 1
2Contents.................................................................... 3
3SAFETY WARNINGS ................................................... 4
CHAPTER 1......................................................................... 5
INTRODUCTION TOYOUR CAMERA ............................................ 5
1.1 CHECKING THE PACKAGE CONTENTS......................................................... 5
1.2 GETTING TO KNOW YOUR CAMERA............................................................ 6
FEATURES AND BENEFITS .................................................................................. 10
1.4 SYSTEM REQUIREMENT........................................................................... 12
CHAPTER 2....................................................................... 13
HARD ARE INSTALLATION .................................................... 13W
2.1 INSTALLING THE CAMERA STAND,WALL MOUNT KIT................................. 13
2.2 CONNECTING THE CAMERA TO LAN/WLAN ............................................. 15
2.3 APPLICATIONS OF THE CAMERA ............................................................... 16
CHAPTER 3....................................................................... 17
ACCESSING THE CAMERA ..................................................... 17
3.1 USING IPFINDER ..................................................................................... 17
3.2 ACCESSING TO THE CAMERA ................................................................... 18
3.3 CONFIGURING THE IP ADDRESS OF THE PC ............................................. 22
CHAPTER 4....................................................................... 23
CONFIGURING THE CAMERA.................................................. 23
4.1 USING THE WEB CONFIGURATION............................................................ 23
4.2 USING SMART WIZARD............................................................................ 24
4.3 BASIC SETUP .......................................................................................... 28
4.4 NETWORK SETTINGS............................................................................... 32
4.5 PAN/TILT SETTINGS** ............................................................................. 40
4.6 SETTING UP VIDEO &AUDIO .................................................................... 41
4.7 EVENT SERVER CONFIGURATION............................................................. 46
4.8 MOTION DETECT ..................................................................................... 51
4.9 EVENT CONFIG ....................................................................................... 52
4.10 TOOLS.................................................................................................... 58
4.11 USB*** .................................................................................................. 60
4.12 INFORMATION ......................................................................................... 62
APPENDIX ........................................................................ 63
A.1 SPECIFICATION ....................................................................................... 63
A.2 GPIO TERMINAL APPLICATION**.............................................................. 65
A.3 GLOSSARY OF TERMS ............................................................................. 67
©MARMITEK
4
3SAFETY WARNINGS
o To prevent short circuits, this product should only be used inside and only in dry spaces.
Do not expose the components to rain or moisture. Do not use the product close to a
bath, swimming pool etc.
o Do not expose the components of your systems to extremely high temperatures or
bright light sources.
o In case of improper usage or if you have altered and repaired the product yourself, all
guarantees expire. Marmitek does not accept responsibility in the case of improper usage
of the product or when the product is used for purposes other than specified. Marmitek
does not accept responsibility for additional damage other than covered by the legal
product responsibility.
o This product is not a toy. Keep out of reach of children.
o Do not open the product: the device may contain live parts. The product should only be
repaired or serviced by a qualified expert.
o Only connect the adapter to the mains after checking whether the mains voltage is the
same as the values on the identification tags. Never connect an adapter when it is
damaged. In that case, contact your supplier.
IP Eye Anywhere ™ IP RoboCam ™ 5
CHAPTER 1
INTRODUCTION TOYOUR
CAMERA
1.1 Checking the Package Contents
Check the items contained in the package carefully. You should have
the following:
5One Network Camera.
5One AC Power Adapter.
5One External Antenna.*
5One Wall Mount Kit.
5One GPIO Connector**
5One Ethernet Cable (RJ-45 type).
5One Installation CD-ROM.
5One Quick Installation Guide.
NOTE Once any item contained is damaged or missing, contact the
authorized dealer of your locale.
1.2 Getting to Know Your Camera
Power LED indicates
the camera is powered
on with the steady
amber light.
Internal Microphone****
allows the camera to
receive sound and voice.
Link LED indicates
the camera’s network
connectivity with the
flashing green light.
Lens Assembly
USB Port*** allows you
to connect an external
USB device.
It provides the power
distribution up to 500mA.
USB*** Unmount
Button
Is used to remove the
connected USB device
safel
y
.
Front view IP Eye Anywhere
©MARMITEK
6
Light Sensor *****
is used to trigger on and off
the Infrared LEDs according
the environmental light level. Antenna*
Infrared LEDs (x7)*****
allow your camera to
capture clear image in
a dark environment.
Lens Assembly
Power LED
indicates the
camera is powered
on with the steady
amber light.
IP Eye Anywhere ™ IP RoboCam ™ 7
Front view IP RoboCam
The camera’s USB*** port supports WCN (Windows Connect Now)
technology, which allows you to use the notebook computer to set
up and store your wireless networking configuration on the USB
storage device, and then retrieve the wireless settings when you
connect the USB storage device to the camera.
NOTE After long pressing the Unmount*** button for four seconds,
the Power LED starts flashing. When the Power LED resumes
the steady amber light, you can remove the USB device safely.
USB Port***
allows you to connect an
external USB device. It
provides the power
distribution up to 500mA.
Link LED
indicates the camera’s
network connectivity
with the flashing green
light.
Internal Microphone *****
allows the camera to receive
sound and voice.
External Antenna*
Screw Hole is used
to connect the camera
stand.
Ethernet Cable Connector
is used to connect the
network cable, which supports
the NWay protocol so that the
camera can detect the
network speed automatically.
DC Power Connector
is used to connect the
A
C power adapter, in
order to supply power
to the camera. Reset Button will restart
the camera when it is
pressed quickly; when it is
long pressed for five
seconds, the camera will
resume the factory default
settings.
Rear View IP Eye AnyWhere
©MARMITEK
8
Ethernet Cable Connector
connects the network
cable, which supports the
NWay protocol so that the
camera can detect the
network speed
automatically.
External Antenna
Connector* connects
the external antenna.
DC Power Connector
connects the AC
power adapter, in
order to supply power
to the camera.
USB Unmount Button ***
is used to remove the
connected USB device
safely.
Audio-out
Connector*****
connects an external
active speaker.
IP Eye Anywhere ™ IP RoboCam ™ 9
GPIO Connectors**
is used to connect the
external devices.
Reset Button
will restart the camera when it
is pressed quickly; when it is
pressed and held for five
seconds, the camera will
resume the factory default
settings.
Rear View IP RoboCam
Este manual sirve para los siguientes modelos
12
Tabla de contenidos
Otros manuales de Cámara de seguridad de Marmitek
Marmitek
Marmitek MEGACAM4 Manual de usuario
Marmitek
Marmitek Gigacam none Manual de usuario
Marmitek
Marmitek MEGACAM1 Manual de usuario
Marmitek
Marmitek SD Memory CAM2 Manual de usuario
Marmitek
Marmitek IP EYE ANYWHERE 470 - ADVANCED Manual de usuario
Marmitek
Marmitek IP EYE ANYWHERE 470 - ADVANCED Manual de usuario
Marmitek
Marmitek IP EYE ANYWHERE - QUICK Manual de usuario
Marmitek
Marmitek IP RoboCam541 Guía de configuración
Marmitek
Marmitek IP EYE ANYWHERE 21 - SOFTWARE ULTRAVIEW Guía de configuración
