Markibar IZAGA KEY Manual de usuario
USER MANUAL
IZAGA KEY
Página nº 1 de 25
The IZAGA automatic coffee grinder is a completely automatic
professional espresso coffee grinder that provides you with just the right
amount of freshly ground coffee quickly and conveniently for the perfect cup
of coffee.
This product has been designed using the latest technology and based on
more than 20 years of experience in the espresso coffee market. The result is a
high-quality product with multiple features that we hope will more than meet
your needs.
Be sure to read and follow the instructions and suggestions found in this
manual to fully and safely benefit from the features of this product.
In the case of a malfunction, contact the manufacturer or the store where
you bought the grinder.
Markibar reserves the right to add any future improvements it deems
appropriate as the result of the company's continuing research.
Página nº 2 de 25
INDEX
1.- Safety instructions.
2.- Technical information.
3.- Description.
4.- Safety features of the grinder.
5.- Installation and set up.
6.- Display.
7.- Problem solving.
8.- Cleaning.
9.- Maintenance.
10.- Declaration of conformity.
11.- Warranty conditions.
12.- Appendix I. Filter-holder identification.
Página nº 3 de 25
1.- Safety instructions.
Please read and pay close attention to the following safety instructions.
The failure to follow these instructions may result in a malfunction or damage
to the machine.
1.1- Symbols.
1.1-1. Safety instructions.
Risk of an accident if this note is not followed.
1.1-2. General instruction.
The machine may be damaged or proper operation is no longer
guaranteed if this instruction is not followed.
1.2- Safety instructions.
The power plug supplied by the manufacturer shall correspond to
the country where the machine is installed.
When unpacking the machine, check to see that the voltage of your
electrical system matches that shown by the manufacturer on the
rating label. Never use the machine in wet or damp areas.
The plastic bags used for packing may pose a safety hazard. Keep
them out of the reach of children.
Unplug the equipment before performing any maintenance or
cleaning tasks.
Never operate the grinder if the electrical cord is in poor condition.
Periodically inspect the electrical cord, the plug, etc. for any possible
damage.
Any repair should be performed by Authorized Service Technicians.
Página nº 4 de 25
For best results, the maximum operating cycle should not exceed 5
seconds of grinding and 10 seconds of stoppage. After 30 minutes of
continuous operation, allow the motor to cool before using it again.
Do no modify or alter the machine in any way. The Manufacturer
assumes no responsibility for damage caused by the failure to follow
these instructions.
This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience or knowledge. Children should be supervised to ensure
they do not play with the appliance.
This appliance can be used by children aged over 8 or persons with
reduced physical, sensory or mental capabilities or lack of
experience and knowledge, with proper supervision and training in
the safe use of the apparatus and understanding of the dangers
involved.
Cleaning and maintenance by the user should not be made by
children without supervision.
In case of damage to the power cord it must be replaced by the
manufacturer, its after-sales service or similarly qualified persons in
order to avoid hazards.
Do not insert objects in the ventilation slots on the grinder.
The grinder must be installed indoors, away from areas where it may
be splashed with water, sprayed with water from cleaning
operations, etc.
Never submerge the grinder in water or operate it with wet hands.
1.3- Using the grinder.
This machine is designed exclusively to grind coffee beans. Do not
use it to grind other products or objects. NEVER put GROUND
COFFEE in the HOPPER.
Página nº 5 de 25
2.- Technical information.
CHARACTERISTICS DATA
VOLTAGE / FREQUENCY 230 V 50 Hz
RATED POWER 525 W
ROTATION 1350 rpm
OVERLOAD FUSE 10 A, Type T
Maximum permitted operating time 50 % on, 50% off
HEIGHT H 640 mm
WIDTH W1/W2 180 mm
DEPTH L 352 mm
WEIGHT 16 kg
BEAN HOPPER CAPACITY 1.5 kg
GRINDING BURRS Ø64
PRODUCTION kg/hour 8 kg
Página nº 6 de 25
3.- Description.
1.- Bean hopper
2.- Hopper closing device.
3.- Grinding adjustment lock.
4.- Hopper fixing device.
5.- Grinding adjustment lever.
6.- Backlit branding area.
7.- Keypad and display.
8.- Press tamp.
9.- Filter-holder rest.
10.- Coffee grounds tray.
11.- Power supply and fuse.
12.- Cleaning access.
A.- Display.
B.- Minus key “–“.
C.- Plus key “+”.
D.- On/Off.
E.- Enter/Programming key.
F - 1 cup selection key.
G - 2 cups selection key.
Página nº 7 de 25
4.- Safety devices.
The grinder motor is protected by a thermal safety device that cuts off the
electricity to the motor if it becomes overheated. This device is
automatically reset when the machine cools.
The user cannot perform any operation on this device. If the device is
repeatedly activated, please consult our Technical Assistance Service, as
the motor may be damaged.
5.- Installation and set up.
Each grinder is factory tested with coffee beans to make sure that it works
properly. For this reason, you may find ground coffee in the grinder's
mechanisms.
5.1.- Grinder location.
Place the grinder on a solid, dry surface next to the coffee machine.
Never operate the grinder in wet or damp places.
5.2.- Installation and set up.
To put the hopper in place first loose
the fixing screw (T).
Página nº 8 de 25
Place the hopper as shown in the picture,
press down till the blocking device (Pos 4)
enters the hole (R) in the hopper neck.
For compliance with safety requirements,
tighten the hopper fixing screw (T) using a
5mm allen wrench.
Insert the coffee grounds tray as shown
in the illustration.
THE GROUND COFFEE SPILLED ON THIS
TRAY MUST NOT BE PUT IN THE HOPPER.
The grinder has a Ø57mm press tamp
placed in the front of the machine and
another Ø53mm press tamp is included in
the box along with the power cord and the
grounds tray. Check which one best matches
the filter-holder of your coffee machine and
change it if needed.
Página nº 9 de 25
To connect the grinder to the power supply, proceed as follows:
- The grinder's electrical connection must be properly protected by current
limiting circuit breakers, a differential switch and a ground connection,
according to current safety regulations.
- Make sure that the voltage and frequency of your establishment match
those indicated on the grinder's rating plate.
- Plug the grinder into the electrical socket. The display will show the
message:
- Open the hopper lid and pour the coffee beans into the hopper. NEVER
put GROUND COFFEE in the hopper
- Make sure that the hopper closing device (Pos. 2) is open.
- Select the desired coffee dose, pressing the corresponding button:
Key F: “ 1 CUP ” o key G: “ 2 CUPS ”.
- Insert the filter-holder from your coffee machine in the filter-holder rest
(Pos. 9) as far as it will go, pressing the switch.
- The corresponding dose is deposited in the filter-holder.
- Compact this dose using the press tamp (Pos. 8) to level off the ground
coffee before placing it in your coffee machine.
- The grinder automatically grinds the corresponding dose.
- Use the ON / OFF key (Pos. D) to turn on and off the grinder. In Off
position, the grinder remains in stand-by mode.
Tabla de contenidos
Otros manuales de Molinillo de café de Markibar
