Mantracourt PSDS-HSBK Manual de usuario

PSDS-HSBK Quick Start Guide

mantracourt.com

PSDS-HSBK

Portable Sensor Display –Strain Bridge

Mantracourt Electronics Limited PSDS HSBK Quick Start Guide

Introduction/overview.........................................................................................................................................2

Getting started......................................................................................................................................................3

Hardware overview.....................................................................................................................................................................................3

Front ............................................................................................................................................................................................................3

Back..............................................................................................................................................................................................................4

Top ...............................................................................................................................................................................................................5

Setting up without the Toolkit............................................................................................................................6

Calibration .....................................................................................................................................................................................................6

Change units.................................................................................................................................................................................................8

Change decimal places.............................................................................................................................................................................8

Overload/underload alarm......................................................................................................................................................................8

Using TEDS ................................................................................................................................................................................................. 10

Toolkit ................................................................................................................................................................ 12

Toolkit overview ....................................................................................................................................................................................... 12

Mantracourt Electronics Limited PSDS HSBK Quick Start Guide

Introduction/overview

The PSDS-HSBK allows simple display of strain bridge based measurements such as load cells and pressure

gauges with sensitivity up to +/-480 mV/V.

Up to six calibration ranges are available allowing for different loading modes (tension and compression) or

different sensors. Each calibration range will remember settings that contribute to the user experience such as

selected units and tare values.

TEDS devices using templates 33, 40 and 41 can be connected and will update the viewed calibration. The last

twenty TEDS devices connected will be remembered and recognized when connected again reverting to the last

user experience settings for that device. TEDS can be disabled and the internal calibration ranges become

available again.

There are also up to six display modes available. These determine what is visible on the LCD display and what

actions are available from the set of three soft keys.

Full configuration is available with a free PC based toolkit. Some simple configuration such as two point

calibration is available from within the handheld using the menu system.

Mantracourt Electronics Limited PSDS HSBK Quick Start Guide

Getting started

This document is designed to give a very quick overview of the PSDS-HSBK and its general, standard functionality.

For more details, see the full manual.

Hardware overview

Front

Mantracourt Electronics Limited PSDS HSBK Quick Start Guide

Back

Mantracourt Electronics Limited PSDS HSBK Quick Start Guide

Top

The Load Cell connector fitted to PSD Standard Product is BINDER 770-8. The cable fitted mating connector is a

BINDER 771 8-way male connector. There are three versions available with different field cable diameters.

View from solder connector side of the connector

Cable pair

Suggested

Colour

Connector

Function

White

Loadcell Reference +ve

Black

Loadcell Reference -ve

Green

Loadcell Signal +ve

Black

Loadcell Signal -ve

Red

Loadcell Excitation +ve

Black

Loadcell Excitation -ve

Blue

TEDS

Black

Ground

Screen

Grey

Cable screen should only be connected to

chassis of the sensor.

If this cannot be achieved, then it should be

connected to Excitation -ve.

Mantracourt Electronics Limited PSDS HSBK Quick Start Guide

Setting up without the Toolkit

Quick, limited setup is possible using just the handheld and no toolkit. To access all the configuration features,

you will need to use the toolkit.

Calibration

Please note that this must be done in the correct order for the calibration to work

correctly. Changing the Sensitivity after inputting mV/V readings will cause the

calibration to be void. Always make sure you finish with Apply

’CALIBRATION’

’USER CALIBRATION’

’ENTER PASSWORD’(if set)

Scrolls through available characters

Moves between digits

’LIVE CALIBRATION’

’SENSITIVITY’

Select required input sensitivity (Note, this MUST be selected before the following

steps)

Return to previous menu

’UNITS’

Select required calibration units

Mantracourt Electronics Limited PSDS HSBK Quick Start Guide

Return to previous menu

’LOW/HIGH CALIBRATION’

’SET OUTPUT LOW’

Manually enter the low output required using to select digits and to change

the value

changes the sign of the entered number

moves the decimal place to the left

moves the decimal to the right

to save changes (long press cancels changes and returns to previous view)

’SET OUTPUT HIGH’

Manually enter the high output required (as above)

to save changes (long press cancels changes)

’CAPTURE mV/V LOW’Apply low load, let load settle then:

Confirm or edit low mV/V input

(You can manually edit the mV/V to a value from a calibration certificate here)

to save changes (long press cancels manual changes)

’CAPTURE mV/V HIGH’Apply high load, let load settle then:

Confirm or edit high mV/V input

(You can manually edit the mV/V value to a value from a calibration certificate here)

to save changes (long press cancels manual changes)

If everything is as planned

Return to previous menu

Mantracourt Electronics Limited PSDS HSBK Quick Start Guide

’APPLY’

Return to previous selected display mode.

Change units

In all standard display modes, scrolls through the available units for the selected calibration.

Change decimal places

In all standard display modes, a 2 second press shifts the decimal place position for the selected units.

Overload/underload alarm

Please note, the values saved for the thresholds are applied in the calibrated units of the

currently selected range. This means that different ranges will trigger at different loads if

the calibrated unit is different.

’ALARM’

’ALARM SOURCE’

Select ‘GROSS’or ‘NET’

Return to previous menu

’ALARM MODE’

Select ‘NORMAL’or ‘LATCHED’

(When the alarm is latched but no longer being triggered, cancel the alarm by:

’ALARM’

Mantracourt Electronics Limited PSDS HSBK Quick Start Guide

’**ALARM CANCEL**’)

’ALARM THRESHOLDS’

’ALARM LOW’

Manually enter the low threshold required using to select digits and

to change the value

changes the sign of the entered number

moves the decimal place to the left

moves the decimal to the right

to save changes (long press cancels changes and returns to display mode)

’ALARM HIGH’

Manually enter the high threshold required as above.

to save changes (long press cancels changes and returns to display mode)

Return to previous menu

’ALARM TRIGGER’

Select from:

Disabled

Outside limits (<low, >high)

Inside limits (>low, <high)

Above high (>high)

Below high (<high)

Above low (>low)

Below low (<low)

Otros manuales para PSDS-HSBK

Tabla de contenidos

Otros manuales de Instrumento de medición de Mantracourt

Mantracourt

Mantracourt BroadWeigh Manual de usuario

Mantracourt

Mantracourt Broadweigh Bluetooth Series Manual de usuario

Mantracourt

Mantracourt PSD Manual de usuario

Mantracourt

Mantracourt BroadWeigh Manual de usuario

Mantracourt

Mantracourt X24 Manual de usuario

Mantracourt

Mantracourt B24 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario