MantaroBot TableTop TeleMe Manual de usuario
MantaroBot™
20410 Century Boulevard Suite 120 Germantown Maryland 20874
www.MantaroBot.com info@mantarobot.com
Phone 301 528 2244 Fax 301 528 1933
MANTAROBOT™ TABLETOP TELEME
Assembly Instructions &
Quick Start Guide
MANTAROBOT TABLETOP TELEME
Assembly Instructions &
Quick Start Guide
MantaroBot™
20410 Century Boulevard Suite 120 Germantown Maryland 20874
www.MantaroBot.com info@mantarobot.com
Phone 301 528 2244 Fax 301 528 1933
2
Table of Contents
Table of Contents.......................................................................................................................................... 2
Assembly Instructions................................................................................................................................... 3
Assembly without Floor Base and Mast Extension................................................................................... 4
Assembly with Floor Base and Mast Extension ........................................................................................7
Installing User Device.............................................................................................................................. 12
Quick Start (when using Android tablets)...................................................................................................15
Quick Start (for TableTop TeleMes with WiFi option) ................................................................................22
MANTAROBOT TABLETOP TELEME
Assembly Instructions &
Quick Start Guide
MantaroBot™
20410 Century Boulevard Suite 120 Germantown Maryland 20874
www.MantaroBot.com info@mantarobot.com
Phone 301 528 2244 Fax 301 528 1933
3
Assembly Instructions
1. Carefully unpack the contents in which your TableTop TeleMe was shipped. DO NOT throw
away the shipping materials. Store them safely so they can be used to ship or transport your
TableTop in the future.
2. Identify the parts in the picture below. The only tool required to assemble your TeleMe is a #1
Phillips screwdriver. Parts D, E, and F are only included if you purchased the Floor Base with
Mast Extension option. Part G (not shown below) is the optional battery module installed in the
base of Part A.
MANTAROBOT TABLETOP TELEME
Assembly Instructions &
Quick Start Guide
MantaroBot™
20410 Century Boulevard Suite 120 Germantown Maryland 20874
www.MantaroBot.com info@mantarobot.com
Phone 301 528 2244 Fax 301 528 1933
4
Assembly without Floor Base and Mast Extension
1. Protruding from bottom of device holder (B) is a male connector. Protruding from top of base
pole (A) is a female connector. Plug male connector from device holder (B) into female
connector of base pole (A). See picture below.
2. Slide pole of device holder (B) all the way down
over the base pole (A) while aligning the two screw
holes in both (A) and (B).
MANTAROBOT TABLETOP TELEME
Assembly Instructions &
Quick Start Guide
MantaroBot™
20410 Century Boulevard Suite 120 Germantown Maryland 20874
www.MantaroBot.com info@mantarobot.com
Phone 301 528 2244 Fax 301 528 1933
5
3. Using a #1 Phillips screw driver, screw two of the provided screws (C) into the pole of device
holder (B) to secure it to base pole (A).
4. Plug in the supplied AC/DC power adapter to the connector located in the cavity on the
underside of the TableTop base. Plug the other end of the power supply cord to a wall outlet.
5. If the optional internal battery option was purchased it was already shipped installed into your
unit. However, the battery was disconnected for shipping. Remove the two screws holding the
MANTAROBOT TABLETOP TELEME
Assembly Instructions &
Quick Start Guide
MantaroBot™
20410 Century Boulevard Suite 120 Germantown Maryland 20874
www.MantaroBot.com info@mantarobot.com
Phone 301 528 2244 Fax 301 528 1933
6
rectangular shaped battery module on the underside of the base. Slide the battery module out,
connect the wire connector from the battery module to the wire connector inside the
compartment, and then slide the battery module back in. Put the two screws back holding the
battery module in place.
MANTAROBOT TABLETOP TELEME
Assembly Instructions &
Quick Start Guide
MantaroBot™
20410 Century Boulevard Suite 120 Germantown Maryland 20874
www.MantaroBot.com info@mantarobot.com
Phone 301 528 2244 Fax 301 528 1933
7
Assembly with Floor Base and Mast Extension
1. If the optional internal battery option was purchased it was already shipped installed into your
unit. However, the battery was disconnected for shipping. Remove the two screws holding the
rectangular shaped battery module on the underside of the TeleMe base (A). Slide the battery
module out, connect the wire connector from the battery module to the wire connector inside
the compartment, and then slide the battery module back in. Put the two screws back holding
the battery module in place.
2. Align the feet of TeleMe base (A) with holes in the Floor Base (F) as shown in the picture below.
MANTAROBOT TABLETOP TELEME
Assembly Instructions &
Quick Start Guide
MantaroBot™
20410 Century Boulevard Suite 120 Germantown Maryland 20874
www.MantaroBot.com info@mantarobot.com
Phone 301 528 2244 Fax 301 528 1933
8
Using thumb screw (E) attach the Floor base to the TeleMe base as shown below.
MANTAROBOT TABLETOP TELEME
Assembly Instructions &
Quick Start Guide
MantaroBot™
20410 Century Boulevard Suite 120 Germantown Maryland 20874
www.MantaroBot.com info@mantarobot.com
Phone 301 528 2244 Fax 301 528 1933
9
3. Protruding from bottom of mast (D) is a male connector. Protruding from top of base pole (A) is
a female connector. Plug male connector from mast (D) into female connector of base (A). See
picture below.
4. Slide mast (D) over the base pole
(A) while aligning the two screw
holes in both (A) and (D). See
picture on the right.
MANTAROBOT TABLETOP TELEME
Assembly Instructions &
Quick Start Guide
MantaroBot™
20410 Century Boulevard Suite 120 Germantown Maryland 20874
www.MantaroBot.com info@mantarobot.com
Phone 301 528 2244 Fax 301 528 1933
10
5. Using a #1 Phillips screw driver, screw two of the provided screws (C) into the bottom of mast
(D) to secure it to base (A). See picture below.
6. Protruding from bottom of device holder (B) is a male connector. Protruding from top of mast
(D) is a female connector. Plug male connector from device holder (B) into female connector of
mast (D). See picture below.
Tabla de contenidos
Manuales populares de Sistema de conferencias de otras marcas
Kramer
Kramer VIA GO Manual de usuario
AVT
AVT MAGIC AC1 Go Manual de usuario
ProSoft Technology
ProSoft Technology AN-X4-AB-DHRIO Manual de usuario
Sony
Sony PCS-I150 Manual de usuario
Middle Atlantic Products
Middle Atlantic Products VTC Series Manual de usuario
Prentke Romich Company
Prentke Romich Company Vanguard Plus Guía
