Makita UB1102 Manual
P 1/ 8
Model No.
Description
Continuous Rating (W)
Voltage (V) Cycle (Hz) Input Output Max. Output (W)
--- ---
--- ---
110
220
230
240
Nozzle .....................................1
Joint .........................................1
Dust bag (capacity of 2L) .......1 (for some countries)
5.7
2.9
2.8
2.7
50/60
50/60
50/60
50/60
600
--- ---120 6.8 50/60 ---
600
--- ---600
--- ---600
Current (A)
Dimensions: mm (")
Width (W)
Height (H)
Length (L) 479 (18-7/8)
185 (7-1/4)
178 (7)
No load speed: min.ˉ¹=rpm
Max. air volume*1: m³/min.
Max. sealed suction: kPa
Protection against electric shock
Power supply cord: m (ft)
*1 Without Nozzle, Joint
*2 With Nozzle, Joint
16,000
Model No. UB1102
Double insulation
Variable speed control No
4.1
Australia: 0.5 (1.64), Others: 2.5 (8.2)
2.0 (4.3)
5.7
0 - 16,000
UB1103
Yes
0 - 4.1
0 - 5.7
UB1102, UB1103
Blower
Weight according to
EPTA-Procedure 01/2003*2: kg (lbs)
Dust bag assembly
Nozzle assembly
Long nozzle assembly
Flexible hose set
Anchor nozzle set (for vacuum function only)
Bending long nozzle set
PRODUCT
Models UB1102, UB1103 Blowers are successors of UB1100, UB1101.
Their output air volume is 4.1m³/min. over the predecessors 2.8m³/min.
The other features are as follows:
•Ergonomic designed handle with elastomer for more comfortable
and controlled operation
•Self-standing design enables stationary use, easy storage and upside-down
standing
The specification difference between UB1102 and UB1103 is;
UB1102: Single speed
UB1103: Variable speed control by dial and trigger
CONCEPT AND MAIN APPLICATIONS
Specification
Standard equipment
Optional accessories
Note: The standard equipment for the tool shown above may vary by country.
L
H
W
TECHNICAL INFORMATION
P 2/ 8
Repair
It is not required to lubricate, because the product has no gear mechanism to be lubricated.
[3] DISASSEMBLY/ASSEMBLY
[3] -1. Switch
CAUTION: Repair the machine in accordance with “Instruction manual” or “Safety instructions”.
[1] NECESSARY REPAIRING TOOLS
[2] LUBRICATION
Fig. 1
DISASSEMBLING
ASSEMBLING
1. Switch can be disassembled without separating Fan housing complete section. See Fig. 1.
Code No. Description Use for
1R370 connecting Ring terminals to Brush holderRing Terminal Setting Jig
1R063 assembling Field to Motor housing completeGuide Bar for fitting Field
Assemble Switch by reversing the disassembly procedure. Refer to Fig. 1.
Note: When mounting Handle cover, be careful of the following.
• Switch and Lead wire are not pinched with Handle cover.
Refer to Fig. D-2 and Fig. D-3.
• There are no gaps between Handle cover and Fan housing complete.
No.1
No.2
Handle cover
Switch
Fan housing
complete
Handle cover
1. Remove four 4x18 Tapping screws
that secure Handle cover to Motor
housing.
4. Remove Switch from Handle section
of Motor housing complete.
2. Separate Handle cover, pulling toward Fan housing complete side
(pulling toward the direction designated with arrow No.1.)
3. Disassemble Handle cover by broadening Handle cover (pulling
its ends toward the direction designated with arrow No. 2).
Now, Handle cover is removed.
P 3/ 8
Repair
[3] DISASSEMBLY/ASSEMBLY
[3] -2. Fan Section
DISASSEMBLING
Disassemble Fan 110 as drawn in Fig. 2.
Assemble Fan Section by reversing the disassembly procedure. Refer to Fig. 2.
Note: Align the hole on Set plate with the protrusion on Fan cover, and insert Set plate by hand, then push it
with a small screwdriver until it stops.
Refer to the drawing on the top right in Fig. 2.
Fig. 2
ASSEMBLING
Fan cover
Fan 110
M5-8 Hex nut
Flat washer 5
Flat washer 8
1. Remove Nozzle. Nozzle
3. Unscrew five 4x18 Tapping screws
and remove Fan cover.
4. Remove M5-8 Hex nut by turning it
counterclockwise with an impact driver while
holding Fan 110 firmly with a gloved hand.
5. Remove Flat washer 5, Fan 110 and Flat washer 8.
Set plate
Fan cover
2. Remove Set plate by prying it off with
a small slotted screwdriver.
P 4/ 8
Repair
[3] DISASSEMBLY/ASSEMBLY
[3] -3. Motor Section
DISASSEMBLING
(1) Remove Carbon brush as drawn in Fig. 3.
(2) Disassemble Fan section as drawn in Fig. 2.
(3) Disassemble Armature as drawn in Fig. 4.
Fig. 3
Fig. 4
Flat washer 8
Armature
Fan housing
complete
1. Unscrew four 4x35 Tapping
screws and disassemble Fan
housing complete.
2. Remove Flat washer 8 from
Armature shaft.
3. Remove Armature from
Motor housing.
Carbon brush
P 5/ 8
Repair
[3] DISASSEMBLY/ASSEMBLY
[3] -3. Motor Section (cont.)
DISASSEMBLING
(4) Disassemble Field as drawn in Fig. 5.
Fig. 5
Switch
Field lead wire
Handle cover
Ring terminal
Field
Field
1. Unscrew four 4x18 Tapping screws and remove Handle
cover.
3. Disconnect Ring terminals from Brush holders
with a Slotted screwdriver.
Note:
Tapping the edge of Motor housing
with a plastic hammer enables Field
to be removed easily.
4. Unscrew two 5x40 Tapping screws and remove
Field from Motor housing.
2. Disconnect Field lead wires from Switch.
P 6/ 8
Repair
[3] DISASSEMBLY/ASSEMBLY
[3] -3. Motor Section (cont.)
ASSEMBLING
(1) Assemble Field to Motor housing. Refer to the drawing on the middle right in Fig. 5.
Also see Fig. D-2 about the wiring of Field lead wires.
Note: Using 1R063 enables Field to be assembled easily than by hand. See Fig. 6.
(2) Connect Ring terminal to Brush holder using 1R370. See
Fig. 7
.
Fig. 6
Ring terminal
1R370
Fig. 7
1R063
Field
(3) Connect field lead wires to Switch and mount Handle cover to Motor housing with four 4x18 Tapping screws.
Refer to the drawings on the top left and right in Fig. 5.
(4) Insert Armature into Motor housing. Refer to the drawing on the right in Fig. 4.
(5) Mount Flat washer 8 to the drive end of Armature's shaft. Refer to the drawing on the center in Fig. 4.
(6) Assemble Fan housing complete with four 4x35 Tapping screws. Refer to the drawing on the left in Fig. 4.
(7) Assemble Fan 110 and Fan cover. Refer to Fig. 2.
And then, set Carbon brush. Refer to Fig. 3.
P 7/ 8
Circuit diagram
Wiring diagram
Fig. D-1
Fig. D-2
White
Noise
suppressor
Switch
viewed from Commutator side
Brush
holder B
Brush
holder A
Line filter
Power supply cord
Color index of lead wires' sheath
Black Blue
Brown
Field
connected to
Switch
Field
Motor housing
complete
Wiring of Field lead wires
connected to
Switch
Slit
Field lead wires
Lead wire
holder
1. Mount Filed to Motor housing complete as shown below.
Lead wire (white or blue) of Power supply
cord connected to P2 terminal
Lead wire (black or brown) of Power supply
cord connected to P1 terminal
Note: Noise suppressor and Line filter are not
used for some countries.
2. Route Field lead wires through the slit
and Lead wire holder as shown below.
P 8/ 8
Wiring diagram
Fig. D-3
Noise suppressor
(if used)
Motor housing
complete
Lead wire
holder
Switch
Field
Power supply
cord
See the drawing
on the right in Fig. D-2.
Line filter (if used)
Set Line filter with Field lead wires
between Lead wire holders.
1. Pass Field lead wires through Line filter
and wind them one turn and pass them
again as shown below.
2. Winded Filed lead wires have to be located on
the Motor housing complete side.
Line filter
Handle cover
Field side
Field lead wires
Motor housing complete
Winded Field
lead wires
Otros manuales para UB1102
7
Tabla de contenidos
Otros manuales de Soplador de Makita
Makita
Makita UB001G Manual de usuario
Makita
Makita EB7660TH Manual de usuario
Makita
Makita UB402MP Instrucciones de operación
Makita
Makita EB5300TH Guía del usuario
Makita
Makita UB101D Manual de usuario
Makita
Makita UB003C Manual de usuario
Makita
Makita DAS180 Manual de usuario
Makita
Makita RBL500 Manual de usuario
Makita
Makita PM7651H Guía del usuario
Makita
Makita BBX7600 Instrucciones de operación
Makita
Makita DUB361Z Manual de usuario
Makita
Makita DUB185 Manual de usuario
Makita
Makita DUB362 Manual de usuario
Makita
Makita M4000 Manual de usuario
Makita
Makita DUB184 Manual de usuario
Makita
Makita UB401MP Guía del usuario
Makita
Makita UB001G Manual de usuario
Makita
Makita DUB186 Manual de usuario
Makita
Makita DUB362 Manual de usuario
Makita
Makita HG5002 Manual de usuario
