Magna-Matic MAG-8200 Series Manual de usuario
Original Instructions
MAG-8200 SERIES
PROFESSIONAL LAWN MOWER BLADE SHARPENERS
AND ALL OPTIONS SETS
2
MAG-8200 LAWNMOWER BLADE SHARPENER
THANK YOU,
We sincerely appreciate your decision to make Magna-Matic your lawn mower blade sharpener. We understand
there are other choices in the marketplace, and we are extremely condent that after the rst few blades you
sharpen, it will be evident you’ve chosen the best machine for the job. Rest assured that if you have a question
or problem you will have complete customer support for all of our products.
800-328-1110 (USA & CANADA) or 920-564-2366
https://www.magna-matic.com
BOX INVENTORY
MAG-8200 (1/2 HP or 1 HP fixed table)
• MAG-8200 Sharpener
• (1) Grit Guard top
• (2) Grit Guard Sides
• (1) Grit Guard Bottom (can be ported or not)
• (1) Crank handle
• (1) Spanner Wrench
• (1) Arbor Wrench
Please be sure all the items are in the box and inspect for shipping damage, or
for missing parts. Contact Magna-Matic right away to remedy any problems due
to shipping. 800-328-1110
Modular Worktable Option
• (1) Modular worktable assembly
• (1) Flat table insert
• (1) Rounded table insert (mulching blades)
• (1) T-Handle wrench
• (1) Arbor Spacer
• (1) 1/2” wide grinding wheel
Belt Grinder Option
• (1) T-Handle wrench
• (1) Eyelet pull tool
• (1) Contact wheel and idler wheel assembly
• (1) 8200-215 abrasive belt
3
Fixed worktable and non-ported grit guard bottom
shown in this image.
Water-Cooled Option
• (1) Water tray
• (1) Splash guards for grit guard (left and right)
• (4) Rubber feet for water tray, hardware, and corner supports
• (1) Coolant tank with pump installed inside
• (1) Coolant lter sock
• (1) 30” length of clear tubing
• (1) Gallon jug of coolant
• (1) Refractometer
• (1) Tube of silicon
• (1) Stand shelf for tank (if purchased with stand)
QUICK START
VIDEOS
SCAN QR CODE
We recommend using the videos, it makes set-up and
understanding the machine much easier.
4
MAG-8200 LAWNMOWER BLADE SHARPENER
Before handling any equipment read and understand the instructions.
THE SAFE WAY IS THE ONLY WAY TO GRIND!
• Grounding Instructions - This tool must be grounded while in use to protect the operator from electric
shock. The tool is equipped with an approved three conductor cord and three prong grounding type plug
to t the proper grounding type receptacle. The green (or green and yellow) wire is the grounding wire.
• Extension Cords - Use only three wire extension cords which have three prong grounding type plugs and
three pole receptacles which accepts the tool’s plug. Replace or repair damaged cords.
• Keep Work Area Clean - Clean benches and oors to prevent slip, trip, or falls.
• Consider Working Environment - Don’t use power tools in damp or wet locations. Keep work area well lit.
Don’t expose power tools to rain.
• Do not use tool in presence of ammable liquids or gases.
• Keep Children Away - All visitors should be kept a safe distance from the work area. Do not let visitors
have contact with the tool or the extension cord.
• Store Idle Tools - When not in use, tools should be stored in dry, high or locked-up places out of reach of
children.
• Do Not Force Tool - It will do the job better and safer at the rate for which it was designed.
• Do Not Over-Reach - Keep proper footing and balance at all times
• Use Safety Glasses - Also face or dust mask-wrap around goggles, or other eye protection.
• Wear Proper Apparel - Do not wear loose clothing or jewelry that can get caught in moving parts. Gloves
and non-skid footwear are required when working. Wear protective hair covering to contain long hair.
• Do Not Abuse Cord - Never carry tool by cord or pull it to disconnect from receptacle.
• Keep cord away from heat, oil, and sharp edges.
• Disconnect Tool - When not in use; before servicing; when changing grinding wheels.
• Avoid Accidental Starting - Don’t carry plugged in tool. Be sure switch is o when plugging in.
• Grinding Wheels - Use only grinding wheels having a maximum operating speed of 5500 RPM.
KEEP GUARDS IN PLACE.
• Guard Against Electrical Shock - Prevent body contact with grounded surface. For example: pipes, radia-
tors, etc.
• Stay Alert - Watch what you are doing. Use common sense. Do not operate tool when you are tired, or
under the inuence of any drugs or alcohol.
• Check Damaged Parts - Before further use of the tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly and perform its intended function.
• Check for alignment of moving parts, breakage of parts, mounting and any other condition that eect
its operation. All parts should be properly repaired or replaced. Do not use this tool if the switch does not
turn it on or o.
• Never Leave Tool Unattended - Turn the power o. Don’t leave the tool until it comes to a complete stop.
• Read “A Primer on Grinding Wheel Safety” https://www.magna-matic.com
WARNING WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAU-
TIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE
THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL
INJURY.
CAUTION LAWN MOWER BLADES HAVE SHARP EDGES - ALWAYS WEAR
PROTECTIVE GLOVES AND SAFETY GLASSES!
5
SAFETY LABELS
SAFETY COLOR DEFINITION
DANGER Interaction with the hazard will
cause severe injury or death.
WARNING Interaction with the hazard could
cause severe injury or death.
CAUTION Interaction with the hazard could
cause minor or moderate injury.
SAFETY
ICON DEFINITION
WARNING
Read all included
manuals and
bulletins included with this equip-
ment.
Always wear protective gloves when
operating this equipment.
Gloves are required.
Always wear protective eye wear
when operating this equipment.
Eye protection
required.
Always wear protective hearing
protection when operating this equip-
ment.
Hearing protection required.
Always wear respiratory protection
when operating this equipment.
Respiratory protection required.
SAFETY
ICON DEFINITION
DANGER Keep clear of the grinding wheel. Con-
tact will cause severe cuts or
abrasions.
Always keep safety guards in place.
DANGER
Disconnect power before servicing
machine
Always keep safety panels in place.
WARNING Keep clear of pulleys and belts. Con-
tact will cause severe injury.
Always keep safety guards in place.
6
MAG-8200 LAWNMOWER BLADE SHARPENER
ASSEMBLY & TESTING
CAUTION TURN OFF
AND UNPLUG
BEFORE SERVICING!
GRIT GUARD ASSEMBLY
1. Use #10 self-tapping screws to assemble the grit guard.
2. Start with the sides, they only t one possible way, check that the holes line up.
3. The grit guard sides t on the inside of the lips.
4. Assemble the grit guard bottom to the top and sides plates
5. The grit guard bottom three lips t on the outside of the grit guard box.
6. Watch the quick start videos for step by step videos.
7
GRIT GUARD TO SHARPENER ASSEMBLY
1. Remove grinding wheel (see page 8-9)
2. Align the bottom of the grit guard to the yellow base of the sharpener. The bottom of the grit guard
should cradle the yellow base.
3. Use two #10 self-tapping screws to connect the grit guard bottom to the sharpener
4. By doing this step rst it will be easier to see which holes line up with the top of the grit guard and
the yellow grinding wheel compartment.
5. Use two button head screws from the inside of the grinding wheel compartment, use the two nylon
nuts to connect the top of the grit guard to the grinding wheel compartment.
WARNING WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAU-
TIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE
THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL
INJURY.
TESTING THE MAG-8200
Before turning the unit on, test the unit by checking if the grinding wheel moves freely. Ensure the MAG-8200
ON/OFF switch is in the OFF POSITION, plug the MAG-8200 into a 15 amp, 110 volt outlet. Switch the ON/OFF
switch to the ON POSITION to test the motor. The motor should achieve FULL speed in 1-2 seconds. If it does
not, (see page ******) or contact MAGNA-MATIC (800-328-1110).
8
MAG-8200 LAWNMOWER BLADE SHARPENER
ASSEMBLY
MOUNTING AND CHANGING GRINDING WHEELS
1. Be sure the MAG-8200 power cord is unplugged.
2. Use the two catch clamps to remove the black front cover.
3. Locate your spanner wrench and arbor wrench (both supplied by Magna-Matic.)
4. The arbor wrench ts into a square notch in the arbor behind the grinding wheel
5. The spanner wrench ts into the two holes in the arbor nut.
6. ARBOR HAS LEFT-HANDED THREADS.
Always inspect grinding wheels for possible damage - never mount a cracked grinding wheel.
DO NOT OVER-TIGHTEN ARBOR NUT - ONLY LIGHT PRESSURE TO TIGHTEN.
The motor will tighten the arbor nut every time the sharpener is turned on.
For optimum performance use only grinding wheels specied by Magna-Matic. All NORTON®
brand grinding wheels sold by Magna-Matic are speed tested for 5500 RPM
NOTE: ARBOR HAS LEFT-HANDED THREADS.
MAG-8200 OEM 1” WHEEL = 9000-35
MAG-8200M OEM 1/2” WHEEL = 8000-30
MAG-8200B OEM 2” ABRASIVE BELT = 8200-215
Purchase replacement grinding wheels & belts at:
https://www.magna-matic-direct.com/grinding-wheels/
STRAIGHT FLAT
CUTTING EDGES
CURVED / WAVY
CUTTING EDGES
HOW TO CHOOSE THE CORRECT GRINDING WHEEL FOR THE BLADE
The 1” wide grinding wheel or 2” wide abrasive belt is used for conventional lawn mower blades with straight at cutting
edges. When you mount the 1” wheel use only the arbor nut. Do not use the arbor spacer with the 1” wide wheel.
This 1/2” wide grinding wheel is required to sharpen curved/wavy cutting edge mulching blade. The arbor spacer (8000-27)
is necessary to mount a 1/2” wide grinding wheel.
Scan Here to buy
abrasives
9
IMPORTANT - PLEASE READ!
MOUNTING 1” WIDE GRINDING WHEEL = ONLY ARBOR NUT
1” WIDE WHEEL + FLAT WHITE TABLE = CONVENTIONAL FLAT BLADES
MOUNTING ORDER
1. WHEEL
2. SPACER
3. ARBOR NUT
IMPORTANT - PLEASE READ!
MOUNTING 1/2” WIDE GRINDING WHEEL = SPACER + ARBOR NUT
1/2” WIDE WHEEL + ROUNDED METAL TABLE = CURVED MULCHING BLADES
10
MAG-8200 LAWNMOWER BLADE SHARPENER
Call with any questions!
800-328-1110
IMPORTANT STAND NOTE:
The MAG-8200 Series mounts in the
same orientation as the MAG-8000. So
when you follow your MAG-10400 Stand
instructions “STEP 7”.
The yellow base of the MAG-8200 is not
threaded so the mounting to the stand is
with a through bolt 1/4”.
The 10400-04 balancer arm base is a
little longer now for the new
MAG-8200 series.
IMPORTANT DUST COLLECTOR
NOTE:
The MAG-8200 Series mounts needs the
MAG-200 Dust Collector
mounted under the grit guard.
It is mounted on the opposite side that it
was for the MAG-8000.
For the MAG-8200 we have moved up to
a 4” diameter grit guard inlet and 4” di-
ameter yellow spiral hose. This increases
the air ow up 400 CFM from 250 CFM.
The table top orientation for the MAG-10400 stand for all MAG-8000,
MAG-8100, and MAG-8200 Sharpeners. This is covered in Step 7 of the
stand instruction sheet.
Use two 1/4-20 x 2” long hex bolts with 1/4
nuts to directly mount the MAG-8100 or
MAG-8200 directly to the stand table top.
For mounting water-cooled units, follow the
water-cooled mounting instructions.
Otros manuales para MAG-8200 Series
1
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Otros manuales de Herramientas eléctricas de Magna-Matic
Magna-Matic
Magna-Matic MAG-8000-7 Manual de usuario
Magna-Matic
Magna-Matic MAG-8000 Series Manual de usuario
Magna-Matic
Magna-Matic MAG-8100 Series Manual de usuario
Magna-Matic
Magna-Matic MAG-8100 Series Manual de usuario
Magna-Matic
Magna-Matic MAG-8200 Series Manual de usuario
Magna-Matic
Magna-Matic MAG-9000 Series Manual de usuario
