Macsense Connectivity XRouter Pro Manual de usuario
Networking the future
XRouter Pro
User’s Manual
MIH-130A
Copyright
Copyright © 2000 by this company. All rights reserved. No part of this doc-
umentation may be reproduced in any form or by any means or used to
make any directive work (such as translation or transformation) without
permission from Xsense Connectivity, Inc. Xsense Connectivity, Inc.
reserves the right to revise this documentation and to make changes in
content without obligation among Xsense Connectivity, Inc. to provide noti-
fication of such revision or change.
All products and their associated features are subject to change or
upgrade at the time of the shipment or of the sales.
FCC Notice
This equipment has been tested and found to be FCC Rules certified.
These restrictions are designed to provide protection against harmful inter-
ference from residential installations. This equipment generates radio fre-
quencies that may cause interference with radio communications if not
used in accordance with the instructions. Interference may even occur
during proper installation. If this equipment causes interference, the user
is suggested to correct the it by one or more of the following:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit that is separate
from the one to which the receiver is connected.
4. Consult the dealer or an experienced radio/television technician for
help.
CE Declaration of Conformity
The equipment complies with the requirements relating to electromanetic
compatiblity, the essential protection requirement of Council Directive/EEC
on the approximation of the Member States relating to Electromangnetic
compatibility.
Trademarks
All products and Brand names are trademarks and/or registered trade-
marks of their respective companies.
I
Safety Precautions
1. Follow all warnings and instructions marked on the product.
2. Slots and openings on the device are provided for ventilation. To
protect it from overheating, these openings must not be blocked or
covered.
3. Do not use or store this product in the environment that exceeds
temperature and humidity specifications. Do not place this product
near a radiator or heat register, or in a built-in installation unless
adequate ventilation is provided.
4. Before cleaning, unplug this product from wall outlet. Do not use
liquid cleansers or aerosol cleansers. Use a damp cloth for
cleaning.
5. Do not place cords or cables where they may be walked on or
tripped over.
6. Be sure to comply with any applicable local safety standards or
regulations.
7. General purpose cables are provided with this product. The use of
any other cables or requirements mandated by local authority is
user’s responsibility.
8. Cables attached to devices in different locations with different
power sources and grounding may cause hazardous voltage.
Consult a qualified electronic consultant before installing the prod-
uct to check if this phenomenon exists and, if necessary, take cor-
rective action.
9. Never touch uninsulated telephone wires or terminals unless the
line has been disconnected.
10. Avoid using telephone equipment or installing the product
during an electrical storm.
11. Never install this product, or any kind of telephone jacks, lines,
network cables, and power connections in wet locations.
12. Never spill liquid of any kind on the product.
II
Contents
1.0 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . .1
1.1 Sharing Internet Access . . . . . . . . . . . . . . . . . . . . . . . . .1
1.2 Modems Supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
1.3 Built-in DHCP Server . . . . . . . . . . . . . . . . . . . . . . . . . . .1
1.4 4-Port Switched Ethernet Hub Inside . . . . . . . . . . . . . . . .2
1.5 Easy Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
1.6 Virtual Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
1.7 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
1.8 NAT (Network Address Translation) . . . . . . . . . . . . . . . . .2
2.0 BEFORE YOU START . . . . . . . . . . . . . . . . . . . . . .3
2.1 Package Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
2.2 Items Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
2.3 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . .3
3.0 EASY INSTALLATION . . . . . . . . . . . . . . . . . . . . . .4
3.1 Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .4
3.1.1 Connecting the XRouter Pro to Your Modem . . . . . . .4
3.1.2 Connecting Computers to the XRouter Pro . . . . . . . .5
3.1.3 Connecting the Power Supply . . . . . . . . . . . . . . . . . .6
3.2 Software Configuration . . . . . . . . . . . . . . . . . . . . . . . . . .7
3.2.1 Setting Up TCP/IP . . . . . . . . . . . . . . . . . . . . . . . . . .7
3.3 Windows 95/98 TCP/IP Configuration of Computers . . . .7
3.3.1 Assigning TCP/IP Values Manually . . . . . . . . . . . . . .9
3.4 Mac OS TCP/IP Configuration . . . . . . . . . . . . . . . . . . . .10
3.4.1 Assigning TCP/IP Values Manually . . . . . . . . . . . . .11
3.4.2 Setting Up the XRouter Pro Through a Web Browser12
4.0 ADVANCED CONFIGURATION . . . . . . . . . . . . . .16
4.1 DHCP Server Settings . . . . . . . . . . . . . . . . . . . . . . . . . .16
4.2 Access Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
4.2.1 URL Access Setting . . . . . . . . . . . . . . . . . . . . . . . .17
4.2.2 IP Access Setting . . . . . . . . . . . . . . . . . . . . . . . . . .18
4.3 Virtual Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
III
4.4 Device Administration . . . . . . . . . . . . . . . . . . . . . . . . . .21
4.5 Status Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
4.6 Special APP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
4.7 DMZ (DeMilitarized Zone) Host . . . . . . . . . . . . . . . . . . .25
4.8 RIP (Routing Information Protocol) . . . . . . . . . . . . . . . .26
4.9 Static Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
4.10 PPPoE Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
4.11 Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
5.0 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . .30
APPENDIX A - Specifications . . . . . . . . . . . . . . . . . .31
APPENDIX B - Hardware Description . . . . . . . . . . . .32
Rear Panel Description . . . . . . . . . . . . . . . . . . . . . . .33
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
IV
1.0 INTRODUCTION
Thanks for purchasing the XRouter Pro MIH-130A Internet Sharing Hub.
The XRouter Pro functions as an easy-to-use communication device which
allows you to connect a local area network (LAN) to the Internet afford-
ably. With the XRouter Pro you can get as many as 252 Macintosh or PC
users online simultaneously through one cable line or DSL, with one ISP
account. The XRouter Pro installs quickly and easily, and best of all, it’s a
breeze to use.
1.1 Sharing Internet Access
The XRouter Pro provides high-speed Internet access to multiple users by
splitting the bandwidth from a cable line or from DSL (Digital Subscriber
Line) into tiny portions and routing these bandwidth “slices” to almost
every Internet users. The fewer the number of users be online at the same
time, the faster the information they receive via internet. Internet users on
different nodes are not limited to access to the same Web pages. Each
node functions independently from the other nodes connected to the
XRouter Pro.
1.2 Modems Supported
The XRouter Pro supports both cable modems and DSL modems. It has
one WAN (Wide Area Network) port to connect itself to a cable modem or
a DSL modem. This provides more than enough bandwidth to accommo-
date the needs of even large groups of Internet users.
1.3 Built-in DHCP Server
The XRouter Pro’s built-in DHCP Server dramatically reduces the amount
of efforts needed for configuration and maintenance by allowing you to
automatically configure the TCP/IP setting over a local area network.
1
Chapter 1 - INTRODUCTION
1.4 4-Port Switched Ethernet Hub Inside
In addition to providing Internet sharing capability, the XRouter Pro also
functions as an Switched Ethernet Hub, which offers four 10/100 Mbps
switched RJ-45 ports that allow you to connect a series of computers to
form a small LAN.
1.5 Easy Configuration
The XRouter Pro can be configured through a Web browser, and it fea-
tures the web-based management for a simple, intuitive set up.
1.6 Virtual Server
Internet users can set up an in-house web server, such as WWW or FTP,
through the XRouter Pro’s Virtual Server mapping function. The Virtual
Server allows you to select a particular computer within the network for
responding to outside Internet requests.
1.7 Security
The XRouter Pro provides firewall-like security through NAT (Network
Address Translation) to prevent unauthorized Internet users from access-
ing internal files. It can also filter out Internet requests from certain nodes
on a local network for administrative purposes.
1.8 NAT(Network Address Translation)
The MIH-130A features NAT (Network Address Translation) as a means of
translating private IP addresses into a global IP address. NAT masks local
IP addresses to the outside world, allowing a group of Internet users to
share a single ISP account. (No separate account is needed for each
users)
2
Chapter 1 - INTRODUCTION
2.0 BEFORE YOU START
2.1 Package Overview
Prior to setting up your XRouter Pro, make sure your XRouter Pro pack-
age includes the following items:
• an XRouter Pro
• a power adapter
• manual
• a Category-5 UTP cable with RJ-45 connectors
2.2 Items Required
• an account from an ISP (Internet Service Provider)
• a cable line or DSL
• a cable modem or DSL modem
• additional UTP cables with RJ-45 connectors (for additional comput-
ers)
2.3 System Requirements
• Computer equipped with 10 BASE-T Ethernet connection inter face
to support TCP/IP protocol
• Windows 95/98/2000, Windows NT 4.0 or that of later versions
• Mac OS 7.5.3 or later versions
• Netscape Communicator 4.0 or above (Microsoft Internet Explorer
4.0 or later versions is necessary for Web configuration.
Note: For future firmware upgrades, one of the operating systems listed
above is needed.
3
Chapter 2 - BEFORE YOU START
3.0 EASY INSTALLATION
3.1 Hardware Installation
Prior to connecting the XRouter Pro to LAN, please be certain that your
cable or DSL service is active and operating correctly. If you are experi-
encing difficulties with the cable or DSL service, please contact the service
provider before continuing the installation process.
3.1.1 Connecting the XRouter Pro to Your Modem
After verifying that your cable or DSL service is functioning properly, con-
nect the cable modem or DSL modem to the XRouter Pro by following the
instructions below:
1. Disconnect the Ethernet cable from the computer that is currently
connected to the DSL or cable modem if you have not done so.
2. Plug the RJ-45 connector from this cable into the WAN (Wide Area
Network) port on the back panel of the XRouter Pro.
(See Figure 3.1-1)
3. Leave the other end of this Ethernet cable connected to the DSL
modem or cable modem.
Figure 3.1-1
4
Chapter 3 - EASY INSTALLATION
3.1.2 Connecting Computers to the XRouter Pro
When you complete connecting the XRouter Pro to your DSL or cable
modem, now you may connect the Macintosh or PC computers in your
local area network to the XRouter Pro. Two methods can be implemented
for the connection: (1) plugging computers directly into the XRouter Pro,
and (2) connecting the XRouter Pro to your LAN hub.
Connect Computers Directly to the XRouter Pro
NOTE: You will need an Ethernet cable for each additional computer con-
necting to the XRouter Pro.
1. Plug one RJ-45 connector (of a standard twisted-pair Ethernet
cable) to the Ethernet port on your computer.
2. Plug the other end of this cable to one of the XRouter Pro’s four
LAN ports (located on the left side of the XRouter Pro’s rear panel.
Refer to Figure 3.1.1)
3. Repeat steps 1 and 2 for each computer you wish to provide
Internet access to until all four XRouter Pro LAN ports are filled.
NOTE: To connect more than four computers to the XRouter Pro, simply plug
additional computers into a network hub and plug this hub into the XRouter
Pro’s uplink port. Read below for further instructions.
Figure 3.1.2
Switch to right for
normal mode
Switch to left for
crossover mode
5
Chapter 3 - EASY INSTALLATION
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
