Macnaught RETRACTA FHM1900-01 Manual de usuario

Introduction

FHM1900-01

FHO1915-01

FHA1220-01

Description

Important

PLEASE READ THIS SAFETY INFORMATION

CAREFULLY BEFORE USE.

Please read and retain this instruction manual to

assist you in the operation and maintenance of this

product.

‘CAUTIONS’ are listed throughout this manual to

advise of actions that may cause personal injury or

damage to your equipment.

CAUTION

Never exceed the pressure rating of any component

in the system.

Check equipment daily for any leaks or damage.

Repair or replace worn or damaged items

immediately with genuine replacement parts.

Before operation check hoses for signs of wear,

leaks or loose fittings. Tighten all fluid connections

regularly and replace weak or damaged hose.

If accidental injection or injury should occur,

seek IMMEDIATE emergency medical attention.

Before attempting any maintenance or repairs of

this product, carefully release the fluid pressure,

before disconnecting the reel, failure to do this

may cause injury

CAUTION

To prevent injury or damage occurring, do not let

go of the hose during rewinding.

DO NOT attempt to stop leaks with your hand, body

glove or rag.

Installation

1) Using the appropriate hardware, bolt the frame

base of the reel to the desired location (See

Drilling Template). Ensure the mounting is strong

enough to support the weight of the reel.

2) Pull out hose to check spring tension and adjust if

required (See Adjusting Spring Tension)

3) Securely connect the fluid supply line to the reel

inlet on the side of the reel.

4) Turn on system and check for any leaks or

damage before use. Repair or reseal if required

4) Securely connect the desired hose-end

attachment to the hose outlet.

Note: Thread sealant may be required

F Series Heavy Duty Hose Reels

Thank you for purchasing the F-Series Heavy

duty hose reel

Your Retracta F-series reel has been manufactured

and constructed using high quality materials.

Hose Installation Procedure

 Truck bed

 Wall (Max 4 meter above the floor)

 Ceiling (Max 4 meter above the floor)

Note: Hose must always pull straight off

the drum as pictured in fig 2 below

Guide arm positions:

Mounting Options

Fig 1

Fig 2

Fig 3

Note: Incorrect hose orientation pictured

in Fig 3 below

Remove Hose Assembly

1) Turn off and disconnect the supply to reel and

release hose line pressure.

2) Pull out approximately 2m (6ft) of hose and allow

the drum to latch.

3) Remove the outlet nozzle, gun or tool and hose

stopper. Unlatch the reel and carefully allow the

hose to slowly rewind until there is no spring tension

remaining.

4) Manually unwind the hose assembly from the

drum. Carefully disconnect and remove the hose

from swivel assembly.

Fit Hose Assembly

5) Connect your new hose assembly to the swivel

assembly.

6) Manually rotate the drum assembly (away from

the roller guides) and manually recoil the hose onto

the drum.

7) Add tension to the reel by carefully rotating the

drum and hose assembly (towards the roller guides)

4 complete turns, slide the hose through the roller

guides and allow the reel to latch.

8) Fit the hose stopper to the hose end, release pull

the hose to release the drum latch, and slowly allow

the hose to slowly rewind onto the reel.

Adjust Spring Tension

1) Allow the hose to fully retract with the hose

stopper sitting against the mouth of the reel.

2) Loosen (but do not remove) the 4 bolts located on

the side of the reel.

3) Insert M12 hex allen key and hold it firmly before

removing the 4 bolts. When the bolt is removed,

the spring tension will transfer to the hex key.

Maintenance

Turn the hex key clockwise (against hose roll out) to

increase tension.

Turn the hex key counter-clockwise (with hose roll

out) to decrease tension.

Increase Tension

Decrease Tension

Note: The spring tension are adjustable at 90°

intervals

5) replace the 4 bolts to complete the adjustment.

6) Unlatch the Drum and check tension.

Repeat (1 - 5) if necessary

Maintenance

Replace Swivel Seals

1) Turn off and disconnect the supply to reel and

release hose line pressure.

2) Remove the supply line to the reel.

3) Remove the outlet nozzle, gun or tool and hose

stopper. Unlatch the reel and carefully allow the

hose to slowly rewind until there is no spring

tension remaining.

4) Remove roller arm (1)

5) Carefully remove the shaft nut (2)

6) Remove the side pedestal from the reel (3)

7) Remove the circlip retaining the swivel body

8) Remove the swivel boy from the shaft.

Note: Remove the hose from swivel body if

required.

9) Remove the old swivel seals, then carefully fit

your new set of seals

10) Lubricate swivel seals with oil, and carefully

slide swivel body onto the swivel shaft, then fit

the circlip

11) The rest of the re-assembly is a direct reversal of

the disassembly procedure.

Diagram and Part List

Order for replacement

Item no Part or Set No off Description

1 SK225s 1 Roller mouth assembly

2 SK223s 1 Latch Set

3 SK220s 1 Swivel Assembly

4 SK221s 1 Swivel Seal Set

5 RHA62s 1 Hose Stopper

6 RH1915HPs 1 Hose Assembly

7 SK224s 2 Bearing Set

Problem Cause Remedy

Hose does not fully

retract

Outlet nozzle, gun or tool is too

heavy

Add spring tension (See “Adjust Spring Tension”)

Spring requires re-tensioning Add spring tension (See “Adjust Spring Tension”)

Replacement hose is too long Fit correct length hose (Refer to Hose Specifications”)

Hose does not retract at

all

Spring has broke or has lost tension Replace spring canister is required

Incorrect operation Reel latches on first, second or third ‘click’. After the

third click reel automatically rewinds

Latch assembly is worn Replace the latch assembly

Fluid leaks from the

swivel

Swivel seals are worn Replace swivel seals (See “Replacement of Swivel

Seals”)

Reel does not latch

Troubleshooting

Dimensional Diagrams

150

130 472

220

280 235

230

250

600

315

590

570

Drilling Template

Note: Drawing Not To Scale

For Warranty Terms and Conditions see macnaught.com.au

For a list of Australian Service Centres see macnaught.com.au

Reel Specifications

Note:

This product should be disposed of according to all applicable local

and national government environment regulations and guidelines.

FHM1900‐01 FHO1915‐01 FHA1220‐01

NominalSize3/4"(19mm)ID 3/4"(19mm)ID 1/2"(12mm)ID

FluidType ‐Oil/Diesel Air/Water

WorkingPressure1450psi 1450psi 250psi

ShaftMaterial SteinlessSteel SteinlessSteel SteinlessSteel

HousingMaterialZincPlatedBrass ZincPlatedBrass ZincPlatedBrass

O‐RingMaterialViton Viton Viton

ReelInlet3/4"BSP(F) 3/4"BSP(F) 1/2"BSP(F)

ReelSwivelOutlet 3/4"BSP(F) ‐‐

Hosetype ‐

WireReforced

Rubber(SAE100R2) ReinforcedPVC

Length15mcapacity 15m 20m

HoseOutlet ‐3/4"BSP(M) 1/2"BSP(M)

IncludedFeederHoseNo Yes Yes

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas de Macnaught

Macnaught

Macnaught KR PRESSURITE Manual de usuario

Macnaught

Macnaught MATP1220 Manual de usuario

Macnaught

Macnaught K29-01 Manual de usuario

Macnaught

Macnaught Retracta R3 Manual de usuario

Macnaught

Macnaught Flexigun K29 Manual de usuario

Macnaught

Macnaught P3 POWERLUBE Manual de usuario

Macnaught

Macnaught HG20R-01 Manual de usuario

Macnaught

Macnaught MINI-LUBE K6 Manual de usuario

Macnaught

Macnaught HG 20F-012KMM-01 Manual de usuario

Macnaught

Macnaught K7/KR MINI-LUBE Series Manual de usuario

Macnaught

Macnaught Retracta F Series Manual de usuario

Macnaught

Macnaught M3D-SSAW3850-H Manual de usuario

Macnaught

Macnaught RETRACTA C1 Manual de usuario

Macnaught

Macnaught B2-01 Manual de usuario

Macnaught

Macnaught K57-01 Manual de usuario

Macnaught

Macnaught powergun pg450 Manual de usuario

Macnaught

Macnaught Lubermate L-AWP1015 Manual de usuario

Macnaught

Macnaught MAN1915-01 Manual de usuario

Macnaught

Macnaught Flexigun K32 Manual de usuario

Macnaught

Macnaught BG100 Manual de usuario

Macnaught

Macnaught lubemate L-AWP1030 Manual de usuario

Macnaught

Macnaught LEVERGUN K40-01 Manual de usuario

Macnaught

Macnaught M3D-SSAW-5050 Manual de usuario

Macnaught

Macnaught M3D-DEF-7530 Manual de usuario

Manuales populares de Herramientas de otras marcas

Martor

Martor SECUNORM 175 Manual de usuario

ERKCO

ERKCO 1000 Manual de usuario

jbc

jbc N4473 Manual de usuario

FEINMETALL

FEINMETALL FZWZ-SET-001 Manual de usuario

Worx Professional

Worx Professional Sonicrafter WU676 Manual de usuario

Gage Bilt

Gage Bilt GB713SH Manual de usuario

Hilti

Hilti DX 9-ENP Manual de usuario

norbar

norbar NORTRONIC 34399 Manual de usuario

BGS technic

BGS technic 8578 Manual de usuario

Makita

Makita DHR241 Manual de usuario

Motor Guard

Motor Guard JMB-1250 Manual de usuario

Power Adhesives

Power Adhesives 805-12 Manual de usuario

Clemco

Clemco 24189 Manual de usuario

VVG

VVG VNG 903 Series Manual de usuario

Hilti

Hilti FX 3-A Manual de usuario

Grizzly

Grizzly H6472 Manual de usuario

axing

axing BWZ 5-02 Manual de usuario

Dh-Robotics

Dh-Robotics RGI-100 Cómo utilizar