M-system M6SPA Manual de usuario

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7974 Rev.5 P. 1 / 4

INSTRUCTION MANUAL

FREQUENCY TRANSMITTER MODEL M6SPA

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Signal conditioner ...............................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES OR UL

•The equipment must be mounted inside a panel.

•The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

•Install lightning surge protectors for those wires connect-

ed to remote locations.

■POWER INPUT RATING & OPERATIONAL RANGE

•Locate the power input rating marked on the product and

conﬁrm its operational range as indicated below:

24V DC rating: 24V ±10%, approx. 0.5W

■GENERAL PRECAUTIONS

•Before you remove the unit or mount it, turn off the power

supply and input signal for safety.

■ENVIRONMENT

•Indoor use.

•When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

•Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

•Environmental temperature must be within -20 to +55°C

(-4 to +131°F) with relative humidity within 30 to 90%

RH in order to ensure adequate life span and operation.

■WIRING

•Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

•Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

•The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

COMPONENT IDENTIFICATION

Body

Front Cover

DIN Rail Adaptor

Specifications

■FRONT VIEW (with the cover open)

Zero Adj.

Power LED

Span Adj.

M6SPA

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7974 Rev.5 P. 2 / 4

INSTALLATION

Set the unit so that its DIN rail adapter is at the bottom. When the unit is installed to an Installation Base (model M6SBS),

refer to its instruction manual.

■MOUNTING THE UNIT ON A DIN RAIL

A)Hang the upper hook at the rear side of unit on the DIN

rail.

B)Push in the lower in keeping pressing the unit to the DIN

rail.

ADIN Rail

■REMOVING THE UNIT

A)Pull down the DIN rail adaptor using a minus screwdriv-

er.

B)Pull out the lower part of the unit.

C)Remove the upper part from the DIN rail.

DIN Rail Adaptor

TERMINAL CONNECTIONS

Connect the unit as in the diagram below or refer to the connection diagram on the side of the unit.

■EXTERNAL DIMENSIONS unit: mm (inch)

94 (3.70)

5.9 (.23)

DIN RAIL

35mm wide

DIN RAIL HOOK

*Use a minus screwdriver: tip width 3.8 mm max., tip thickness 0.5 to 0.6 mm

102 (4.02)

[0.5 (.02)]

SCREWDRIVER

INSERTION ANGLE

: approx. 40°

WIRE INSERTION ANGLE

: approx.35°

TEST PROBE

max. 2 (.08) dia.

SCREWDRIVER

INSERTION ANGLE

: approx. 35°

5678

1234

• When mounting, no extra space is needed between units.

M6SPA

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7974 Rev.5 P. 3 / 4

■CONNECTION DIAGRAM

2.4 kΩ

–

2.5 V

–

OUTPUT

–

INPUT

■ Open Collector or

Mechanical Contact

Input Connection Examples

■ Voltage Pulse

–

POWER

CONNECTOR

POWER

■WIRING INSTRUCTIONS

 •Applicablewiresize

Solid: 0.2 to 2.5 mm2(0.55 to 1.75 dia.)

Stranded: 0.2 to 2.5 mm2(Tinning wire ends may

cause contact failure and therefore is not

recommended.)

Ferruled: 0.2 to 1.5 mm2(0.55 to 1.35 dia.)

 •Exposewireconductorsby8mm(0.31”).

Expose 8 mm

• How to Connect Wires

Screwdriver

Wire

1) Insert a minus screwdriver into the wire entry opening,

between the clamp and the housing, until its tip hits the

bottom where it is ﬁrmly held.

Tension Clamp

Screwdriver

2) Insert a wire. Push the screwdriver toward the direction

indicated with the arrow in the ﬁgure below to widen the

opening if necessary.

Wire Entry

Wire

3) Conﬁrm that the wire tip hits the bottom and pull out the

screwdriver in holding it in position.

Conﬁrm that the wire’s insulation tube is not caught in

the clamp.

M6SPA

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7974 Rev.5 P. 4 / 4

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Conﬁrm that the wire insulation tubes are not caught in

the clamp.

3) Power input voltage: Check voltage across the terminal

7–8withamultimeter.

4) Input: Check that the input signal is within 0 – 100% of

the full-scale.

5) Output: Check that the load resistance meets the de-

scribed speciﬁcations.

ADJUSTMENT PROCEDURE

This unit is calibrated at the factory to meet the ordered

speciﬁcations, therefore you usually do not need any cali-

bration.

For matching the signal to a receiving instrument or in case

of regular calibration, adjust the output as explained in the

following.

■HOW TO CALIBRATE THE OUTPUT SIGNAL

Use a signal source and measuring instruments of sufﬁcient

accuracy level. Turn the power supply on and warm up for

more than 10 minutes.

1) ZERO: Apply 0% input and adjust output to 0%.

For a bidirectional output (e.g. -5 – +5 V DC), apply an

input signal corresponding to 0 V DC output. (Same pro-

cedure in (3))

2) SPAN: Apply 100% input and adjust output to 100%.

3) Check ZERO adjustment again with 0% input.

4) When ZERO value is changed, repeat the above proce-

dure 1) – 3).

MAINTENANCE

Regular calibration procedure is explained below:

■CALIBRATION

Warm up the unit for at least 10 minutes. Apply 0%, 25%,

50%, 75% and 100% input signal. Check that the output

signal for the respective input signal remains within accu-

racy described in the data sheet. When the output is out of

tolerance, recalibrate the unit according to the “ADJUST-

MENTPROCEDURE”explainedearlier.

LIGHTNING SURGE PROTECTION

M-System offers a series of lightning surge protector for

protection against induced lightning surges. Please contact

M-System to choose appropriate models.

Otros manuales de Transmisor de M-system

M-system

M-system MLV Manual de usuario

M-system

M-system M3LT Manual de usuario

M-system

M-system M6DVF Manual de usuario

M-system

M-system M3SXV Manual de usuario

M-system

M-system M5VSH Manual de usuario

M-system

M-system M3LLC Manual de usuario

M-system

M-system M3LM Manual de usuario

M-system

M-system B3FR Manual de usuario

M-system

M-system W2SP Manual de usuario

M-system

M-system TM Manual de usuario

M-system

M-system 6LC Manual de usuario

M-system

M-system M3LM Manual de usuario

M-system

M-system 10JM Manual de usuario

M-system

M-system Mini-M M2RT Manual de usuario

M-system

M-system Mini-M M2DU Manual de usuario

M-system

M-system Mini-M M2YV Manual de usuario

M-system

M-system M2EXV Manual de usuario

M-system

M-system 10JT Manual de usuario

M-system

M-system 27PM Manual de usuario

M-system

M-system 10VF Manual de usuario

M-system

M-system Mini-M M2UDS Manual de usuario

M-system

M-system M5YV Manual de usuario

M-system

M-system CT TRANSMITTER Manual de usuario

M-system

M-system M5 Series Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario