M-system 99SVA Manual de usuario

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Signal conditioner ...............................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■POWER INPUT RATING & OPERATIONAL RANGE

• Locate the power input rating marked on the product and

conﬁrm its operational range as indicated below:

85 – 264V AC rating: 85 – 264V, 50/60 Hz, approx. 75VA

Power consumption: Approx. 12W (excluding that of out-

put current)

■GENERAL PRECAUTIONS

• Before you remove the unit or mount it, turn off the power

supply and input signal for safety.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -5 to +45°C

(23 to 113°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

• Be sure to put the terminal cover on while the power is

supplied.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

COMPONENT IDENTIFICATION

Specifications

Connection Diagram

Body

INSTALLATION unit: mm (inch)

100 (3.94)

120 (4.72)

160 (6.30) min.

4–M4

SCREW

Observe at the minimum of 30 mm (1.2”) for ventilation in all directions.

1A OUTPUT TRANSMITTER MODEL 99SVA

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-1684 Rev.3 P. 1 / 2

INSTRUCTION MANUAL

TERMINAL CONNECTIONS

Connect the unit as in the diagram below or refer to the connection diagram on the front of the unit.

■EXTERNAL DIMENSIONS unit: mm (inch)

100 (3.94)

202 (7.95)

130 (5.12)

100 (3.94)

120 (4.72)

130 (5.12)

2.5 (.01)

4–R2.5 MTG HOLE

■CONNECTION DIAGRAM

–

INPUT OUTPUT

1 3

FG 5

POWER

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 1.2 N·m

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Power input voltage: Check voltage across the terminal

6 – 7 with a multimeter.

3) Input: Check that the input signal is within 0 – 100% of

the full-scale.

4) Output: Check that the load resistance meets the de-

scribed speciﬁcations.

ADJUSTMENT PROCEDURE

This unit is calibrated at the factory to meet the ordered

speciﬁcations, therefore you usually do not need any cali-

bration.

For matching the signal to a receiving instrument or in case

of regular calibration, adjust the output as explained in the

following.

■HOW TO CALIBRATE THE OUTPUT SIGNAL

Use a signal source and measuring instruments of sufﬁcient

accuracy level. Turn the power supply on and warm up for

more than 10 minutes.

1) ZERO: Apply 1% input and adjust output to 1%.

2) SPAN: Apply 100% input and adjust output to 100%.

3) Check ZERO adjustment again with 1% input.

4) When ZERO value is changed, repeat the above proce-

dure 1) – 3).

MAINTENANCE

Regular calibration procedure is explained below:

■CALIBRATION

Warm up the unit for at least 10 minutes. Apply 1%, 25%,

50%, 75% and 100% input signal. Check that the output

signal for the respective input signal remains within accu-

racy described in the data sheet. When the output is out of

tolerance, recalibrate the unit according to the “ADJUST-

MENT PROCEDURE” explained earlier.

LIGHTNING SURGE PROTECTION

M-System offers a series of lightning surge protector for

protection against induced lightning surges. Please contact

M-System to choose appropriate models.

99SVA

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-1684 Rev.3 P. 2 / 2

Otros manuales de Transmisor de M-system

M-system

M-system M2ADS Manual de usuario

M-system

M-system WRS2 Manual de usuario

M-system

M-system Mini-M M2XU Manual de usuario

M-system

M-system 6M Manual de usuario

M-system

M-system KWVS2 Manual de usuario

M-system

M-system 10VF Manual de usuario

M-system

M-system JR Manual de usuario

M-system

M-system Mini-M M2XUM Manual de usuario

M-system

M-system 6PA Manual de usuario

M-system

M-system 6LC Manual de usuario

M-system

M-system MXV Manual de usuario

M-system

M-system FJR Manual de usuario

M-system

M-system W2CFG Manual de usuario

M-system

M-system M5YV Manual de usuario

M-system

M-system M1EXV-4 Manual de usuario

M-system

M-system MFS2 Manual de usuario

M-system

M-system MXLC Manual de usuario

M-system

M-system VOS2T Manual de usuario

M-system

M-system 6BR Manual de usuario

M-system

M-system M3SXT Manual de usuario

M-system

M-system M2LR Manual de usuario

M-system

M-system 10JV Manual de usuario

M-system

M-system Mini-M M2MS Manual de usuario

M-system

M-system 10JPA Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario