M-system 17PE Manual de usuario

17PE

P. 1 / 2EM-2938

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: inf[email protected].jp

COMPONENT IDENTIFICATION

Body

Specifications

Front Cover

(Connection diagram

behind)

■FRONT PANEL CONFIGURATION (with the cover open)

Span Adj.

Zero Adj.

INSTALLATION

Use Standard Rack (model: 17BXE).

BEFORE USE ....

Thank you for choosing M-System. Before use, check the

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System's Sales Ofﬁce or representatives.

■ PACKAGE INCLUDES:

Signal conditioner ....................................................(1)

■ MODEL NO.

Conﬁrm that the model number described on the product is

exactly what you ordered.

■ INSTRUCTION MANUAL

This manual describes necessary points of caution when you

use this product, including installation, connection and basic

maintenance procedures.

POINTS OF CAUTION

■ POWER INPUT RATING & OPERATIONAL RANGE

24 V DC ±10%, approx. 35 mA

■ REMOVING THE UNIT

• Before you remove the unit or mount it, turn off the power

supply and input signal for safety.

■ ENVIRONMENT

• Indoor use

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not apply physical impact to the unit.

• Environmental temperature must be within -5 to +55°C

(23 to 131°F) with relative humidity within 40 to 85% RH in

order to ensure adequate life span and operation.

■ WIRING

• Do not install cables (power supply, input and output) close

to noise sources (relay drive cable, high frequency line, etc.).

• Do not bind these cables together with those in which noises

are present. Do not install them in the same duct.

■ AND ....

• The unit is designed to function as soon as power is supplied,

however, a warm up for 10 minutes is required for satisfying

complete performance described in the data sheet.

PT TRANSMITTER MODEL 17PE

INSTRUCTION MANUAL

17PE

P. 2 / 2EM-2938

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: inf[email protected].jp

TERMINAL CONNECTIONS

Connect the unit as in the diagram below or refer to the connection diagram behind the front cover.

■ DIMENSIONS mm (inch)

110 (4.33 )

93 (3.66)

24 (.94)

7 (.28)

78 (3.07)32 (1.26)

8–M3.5

SCREW

7 (.28)

2–M3

SCREW

■ CONNECTION DIAGRAM

LOAD

SOURCE

FUSE

OUTPUT

AUXILIARY

POWER

CONNECTOR

■ TERMINAL ASSIGNMENTS

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Auxiliary power supply voltage: Check voltage supplied to

the rack (model: 17BXE). Use a power source of ripple

level 10% p-p or less.

3) Input: Check that the input voltage is within 0 – 120%

of the rated voltage.

4) Output: Check that the load resistance meets the described

speciﬁcations.

ADJUSTMENT PROCEDURE

This unit is calibrated at the factory to meet the ordered speci-

ﬁcations, therefore you usually do not need any calibration.

For matching the signal to a receiving instrument or in case

of regular calibration, adjust the output as explained in the

following.

■ HOW TO CALIBRATE THE OUTPUT SIGNAL

Use a signal source and measuring instruments of sufﬁcient

accuracy level. Turn the auxiliary power supply on and warm

up for more than 10 minutes.

1) ZERO: Apply 0% input and adjust output to 0%.

2) SPAN: Apply 100% input and adjust output to 100%.

3) Check ZERO adjustment again with 0% input.

4) When ZERO value is changed, repeat the above procedure

1) – 3).

MAINTENANCE

Regular calibration procedure is explained below:

■ CALIBRATION

Warm up the unit for at least 10 minutes. Apply 0%, 25%,

50%, 75% and 100% input signal. Check that the output

signal for the respective input signal remains within accuracy

described in the data sheet. When the output is out of toler-

ance, recalibrate the unit according to the "ADJUSTMENT

PROCEDURE" explained earlier.

LIGHTNING SURGE PROTECTION

In order to protect the unit from lightning surges entering

through signal and power supply cables, use of appropriate

lightning surge protectors are recommended. Please contact

M-System.

Otros manuales de Transmisor de M-system

M-system

M-system Mini-M M2RTS Manual de usuario

M-system

M-system CT TRANSMITTER Manual de usuario

M-system

M-system M3LPA Manual de usuario

M-system

M-system MLV Manual de usuario

M-system

M-system W2CFG Manual de usuario

M-system

M-system M3LU2 Manual de usuario

M-system

M-system KAC Manual de usuario

M-system

M-system F2VS Manual de usuario

M-system

M-system B3VS/2 Manual de usuario

M-system

M-system MXS Manual de usuario

M-system

M-system VOS2T-R Manual de usuario

M-system

M-system M6SVF Manual de usuario

M-system

M-system 10VS4 Manual de usuario

M-system

M-system M5CT Manual de usuario

M-system

M-system WRS2 Manual de usuario

M-system

M-system Mini-M M2CA Manual de usuario

M-system

M-system M2VF Manual de usuario

M-system

M-system 6AC Manual de usuario

M-system

M-system M5XWTU Manual de usuario

M-system

M-system MXT Manual de usuario

M-system

M-system 10JFT Manual de usuario

M-system

M-system 35mm Manual de usuario

M-system

M-system W2TS Manual de usuario

M-system

M-system Mini-M M2RT Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario