M-system MD7G Manual de usuario

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8065 Rev.2 P. 1 / 2

INSTRUCTION MANUAL

TERMINAL BLOCK FOR GROUNDING

(ultra-slim) MODEL MD7G

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Terminal block.....................................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation and connection.

POINTS OF CAUTION

■ENVIRONMENT

•Indoor use.

•When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

•Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

•Environmental temperature must be within -25 to +85°C

(-13 to +185°F) with relative humidity within 30 to 90%

RH in order to ensure adequate life span and operation.

•This unit needs a DIN rail as earth grounding bar. Ox-

ide coating of an aluminium rail may lower the electric

conductivity between this module and the ground. Use a

steel or copper rail.

COMPONENT IDENTIFICATION

Body

Spring Loader

DIN Rail Mounting

Adaptor (for grounding)

Connection

Diagram

(left side)

Model No.

Indication

INSTALLATION

Mount the unit on a DIN rail. Once installed, do not move

it to another DIN rail.

■MOUNTING THE UNIT ON A DIN RAIL

A)Hang the upper hook of the DIN rail mounting adaptor at

the rear side of unit, on the DIN rail.

B)Push in the lower in keeping pressing the unit to the DIN

rail.

C)DIN rails generally have slight individual variability in

size. If you ﬁnd it difﬁcult to push in the lower part, go

back to (A) and hang the upper part more deeply onto the

rail and try (B) again.

DIN Rail

■REMOVING THE UNIT

A)Push down the spring loader utilizing a minus screwdriv-

er.

B)Conﬁrm that it is pulled enough down and pull out the

lower part of the unit.

C)Detach the upper part from the DIN rail.

Spring Loader

MD7G

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8065 Rev.2 P. 2 / 2

TERMINAL CONNECTION

Connect the unit as in the diagram below.

Be sure to ground the DIN rail on which the unit is mounted.

This unit, designed to connect shield wires and cross wires of the protected devices to a DIN rail, is NOT used to ground the

DIN rail.

■EXTERNAL DIMENSIONS unit: mm (inch)

95 (3.74)

(.28)

98 (3.86) [1.5 (.06)]

8–M3 EURO

TERMINAL

DIN RAIL

(35 mm wide)

DIN RAIL

ADAPTOR

WIRE INSERTION ANGLE: approx. 20°

57 (2.24)

1.9 (.07)

■CONNECTION DIAGRAM

2 5

3 6

1 4

DIN RAIL ADAPTOR

(for grounding)

DIN RAIL

Grounding

DO NOT connect to unused terminals.

*1. Oxide coating of an aluminium rail may lower the electric conductivity

between this module and the ground. Use a steel or copper rail.

*2. Be sure to ground the DIN rail.

Recommended grounding resistance ≤100Ω

WIRING INSTRUCTIONS

■EURO TERMINAL

Torque: 0.3 N·m

Applicable wire size: 0.2 – 2.5 mm2

Stripped length: 8 mm

■CAUTION WHEN WIRING

Hold the module steady at the front when you

tighten/loosen screw terminals.

Otros manuales de Protector contra sobretensiones de M-system

M-system

M-system MDCAT-A Series Manual de usuario

M-system

M-system MDP-SP Manual de usuario

M-system

M-system MMH-1 Manual de usuario

M-system

M-system MD7PL Manual de usuario

M-system

M-system MAKN Manual de usuario

M-system

M-system MD7TC Manual de usuario

M-system

M-system MDR2 Manual de usuario

M-system

M-system MDH Manual de usuario

M-system

M-system MD73W Manual de usuario

M-system

M-system MDA-TL Manual de usuario

M-system

M-system MDPA-24 Manual de usuario

M-system

M-system MDP-RB Manual de usuario

M-system

M-system MDCAT-SPE Manual de usuario

M-system

M-system MDP-JS Manual de usuario

M-system

M-system MMAH Series Manual de usuario

M-system

M-system MAT2 Series Manual de usuario

M-system

M-system MDCAT 5E Manual de usuario

M-system

M-system MDPA-24 Manual de usuario

M-system

M-system MDP-200T Manual de usuario

M-system

M-system MDP-DM3 Manual de usuario

M-system

M-system MD7PA Manual de usuario

M-system

M-system MDCAT-SPE-A Manual de usuario

M-system

M-system MD7FB Manual de usuario

M-system

M-system MD7JS Manual de usuario

Manuales populares de Protector contra sobretensiones de otras marcas

ELAC

ELAC ProteK PR91-W Manual de usuario

Tsubaki

Tsubaki TSM4000M1 Manual de usuario

QVS

QVS PP134C Manual de usuario

CyberPower

CyberPower CSP604T Manual de usuario

Davis Instruments

Davis Instruments Radio Surge Protector Manual de usuario

CyberPower

CyberPower CSP706T Manual de usuario

CyberPower

CyberPower B300WRC1 Manual de usuario

Leviton

Leviton 51120-3R Manual de usuario

Panamax

Panamax MAX 5400-EX Manual de usuario

CyberPower

CyberPower B1006T Manual de usuario

OBO Bettermann

OBO Bettermann ÜSM-20-230I1PE65 Manual de usuario

Minuteman

Minuteman MMS7120RCT Manual de usuario

Leviton

Leviton 52412-DS3 Manual de usuario

Savio

Savio LZ-07 Manual de usuario

Siemens

Siemens HNM3M120 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric LITOL LTM-125RF Manual de usuario

Intermatic

Intermatic PS3000 Manual de usuario

ASCO POWER TECHNOLOGIES

ASCO POWER TECHNOLOGIES 360 Manual de usuario