M-system M8SED Manual de usuario

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Signal conditioner ...............................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■POWER INPUT RATING & OPERATIONAL RANGE

• Locate the power input rating marked on the product and

conﬁrm its operational range as indicated below:

24V DC rating: 24V ±10%, approx. 60mA

■GENERAL PRECAUTIONS

• Before you remove the unit or mount it, turn off the power

supply and input signal for safety.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within 0 to 55°C (32

to 131°F) with relative humidity within 30 to 95% RH in

order to ensure adequate life span and operation.

• Be sure that the ventilation slits are not covered with ca-

bles, etc.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

COMPONENT IDENTIFICATION

Output 1 Monitor LED

Output 1

Setpoint Adj.

Output 2

Setpoint Adj.

Output 2 Monitor LED

Mounting Screw

Body

Specifications

INSTALLATION

Use Installation Base (model: M8BSx).

DC ALARM

(thumbwheel switch adjustment) MODEL M8SED

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-5488 Rev.2 P. 1 / 2

INSTRUCTION MANUAL

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit: mm (inch)

I/O PINS

17.5 (.69)

48 (1.89)

75 (2.95)

83 (3.27)

■CONNECTION DIAGRAM

Installation Base

OUTPUT 1

–

OUTPUT 2

POWER

–

INPUT

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Power input: Check the power input voltage.

3) Input: Check that the input signal is within 0 – 100% of

the full-scale.

4) Check that the output load is 125V AC/25VA or 60V

DC/15W at the maximum. For maximum relay life with

inductive loads, external protection is recommended.

When used with a multi-channel installation base (e.g.

M8BS-16), the ratings derated as following.

Terminal block type: 125V AC @ 0.2A, 30V DC @ 0.25A

Cable connector type: 24V AC @ 50mA, 24V DC @ 50mA

ALARM TRIP OPERATION

TRIP

ACTION

OUT

CODE

POWERED UNPOWERED

INP < SET INP > SET

OUT

Hi 1 OFF ON OFF

Hi 2 ON OFF ON

OUT

Lo 1 ON OFF OFF

Lo 2 OFF ON ON

ADJUSTMENT PROCEDURE

Turn the front thumbwheel SW to indicate desired set-

points in %.

Output 1 is for high trip, while Output 2 is for low.

Monitor LED turn ON when the coil is energized; Output 1

coil is energized when the input is above the setpoint, while

Output 2 coil is when the input is below the setpoint.

Relay contact turns ON when the coil is energized with Out-

put Code 1, de-energized with Output Code 2.

MAINTENANCE

Regular calibration procedure is explained below:

■CALIBRATION

Warm up the unit for at least 10 minutes.

• Hi Setpoint

Increase the input signal from a value lower than the set-

point and check that the relay trips at the setpoint.

• Lo Setpoint

Decrease the input signal from a value higher than the

setpoint and check that the relay trips at the setpoint.

When the trip points are shifted, please contact M-System’s

Sales Ofﬁce or representatives.

LIGHTNING SURGE PROTECTION

M-System offers a series of lightning surge protector for

protection against induced lightning surges. Please contact

M-System to choose appropriate models.

M8SED

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-5488 Rev.2 P. 2 / 2

Otros manuales de Sistema de seguridad de M-system

M-system

M-system 48NDT Manual de usuario

M-system

M-system M8SED1 Manual de usuario

M-system

M-system M6DXAR Manual de usuario

M-system

M-system KSL-x5 Manual de usuario

M-system

M-system Mini-M M2SED Manual de usuario

M-system

M-system KSE-x2 Manual de usuario

M-system

M-system 48NDVA Manual de usuario

M-system

M-system 48NAT Manual de usuario

M-system

M-system AS4V Manual de usuario

M-system

M-system AYDV Manual de usuario

M-system

M-system AS4CT Manual de usuario

M-system

M-system AS4T Manual de usuario

M-system

M-system AS4V Manual de usuario

M-system

M-system KS2V3 Manual de usuario

M-system

M-system AS4R Manual de usuario

M-system

M-system ASD1 Manual de usuario

M-system

M-system KSL2 Manual de usuario

M-system

M-system AS4CT Manual de usuario

M-system

M-system 48NDVD Manual de usuario

M-system

M-system ASWL2 Manual de usuario

M-system

M-system M2AS Manual de usuario

M-system

M-system KS2V2 Manual de usuario

M-system

M-system M1EAXV-2 Manual de usuario

M-system

M-system M1EAXV-1 Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario