M-system R8-DC4C Manual de usuario

R8-DC4C

P. 1 / 4EM-9743 Rev.1

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

PHOTO MOSFET RELAY OUTPUT MODULE

(4 points) MODEL R8-DC4C

INSTRUCTION MANUAL

BEFORE USE ....

Thank you for choosing M-System. Before use, check the

contents of the package you received as below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■ PACKAGE INCLUDES:

Photo MOSFET relay output module......................... (1)

■MODEL NO.

Conﬁrm that the model number described on the product is

exactly what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

•Theequipmentmustbemountedinsideapanel.

•Theactualinstallationenvironmentssuchaspanelcon-

ﬁgurations, connected devices and connected wires may

affect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure CE conformity.

■GENERAL PRECAUTIONS

•Beforeyouremoveormounttheunit,turnoffthepower

supply and output signal for safety.

•Switches on the side of the module can be set for mainte-

nance only while the power supply is off. Do not access

them while the power is supplied.

■ ENVIRONMENT

•Indooruse

•Whenheavydustormetalparticlesarepresentintheair,

install the unit inside proper housing with sufﬁcient ven-

tilation.

•Donotinstalltheunitwhereitissubjectedtocontinuous

vibration. Do not apply physical impact to the unit.

•Environmentaltemperaturemustbewithin-10to+55°C

(14to131°F)withrelativehumiditywithin30to90%RH

in order to ensure adequate life span and operation.

■WIRING

•Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

•Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

•Theunitisdesignedtofunctionassoonaspowerissup-

plied,however,awarmupfor10minutesisrequiredfor

satisfying complete performance described in the data

sheet.

INSTALLATION

■HOW TO MOUNT THE MODULE ON DIN RAIL

• I/O Module

Confirm that the locking clamps of the I/O module are set.

Insert the module in parallel to the next one while aligning the grooves of

both modules (A & B in the above figure).

Maintain it perpendicularly to the rail.

More I/O modules can be added in the same manner.

R8-DC4C

P. 2 / 4EM-9743 Rev.1

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

■HOW TO UNMOUNT THE MODULE FROM DIN RAIL

Release the locking clamps and pull out straight the module.

Caution !

1) Be careful not to hurt your hand by pointed edges of the internal

communication bus connector.

2) I/O modules cannot hold tightly on the DIN rail by themselves without

power/network module.

Secure them to the position if necessary by using DIN rail end plates.

• Removing an intermediate module

• Protective Cover

The protective cover is to be attached over the connected I/O module

at the right end.

Align the hooks on the cover with the grooves of the module and slide it

straight until the hooks are latched.

When removing the cover, pull it out while squeezing the hooks inward.

Groove

Hook

R8-DC4C

P. 3 / 4EM-9743 Rev.1

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

COMPONENT IDENTIFICATION

RUN

Module Address Setting

Rotary SW

Function Setting

DIP SW

Terminator DIP SW

SW1

x10

12345678

SW2

SW4

SW3Term

Status Indicator LED

Output Status Indicator LED

Internal Bus Connector

Output Connectors

FRONT VIEW SIDE VIEW

CARD ADD.

DO1

DO2

DO3

DO4

■INDICATOR LED

LED

OPERATION

FUNCTION

Status OFF Stopping

Green ON Valid host communication

Green Blinking

Reading/writingconguration

RedON Setting error

RedBlinking Parameter error

Output

Status

OFF OFF

Green ON ON

■OUTPUT CONNECTOR ASSIGNMENT

PIN ID FUNCTION

No.

1 DO Discrete output

2 NC No connection

3 NC No connection

4 DO Discrete output

■PC CONFIGURATOR

The following parameters can be set with using PC Conﬁgu-

ratorSoftware(model:R8CFG):

•Outputatthestartup

•Outputatthelossofcommunication

•Commonsetting(lossofinternalbuscommunicationde-

tection time)

TurnSW4-8ONtoallowprogrammingbythePCCongu-

ratorviathePower/NetworkModule.

RefertotheusersmanualfortheR8CFGfordetailedopera-

tion of the software program.

■MODULE ADDRESS

■Module Address

The left switch determines the tenth place digit, while the

right switch does the ones place digit of the address.

Address is selected between 0 to 31.

(Factory setting: 0)

Module Address Setting (x1)

Module Address Setting (x10)

■OPERATING MODE

*Factory setting

• Output at The Loss of Communication

OUTPUT AT THE LOSS OF COMMUNICATION SW4-7

OutputHold(*)

(last data correctly rerceived is hold)

OFF

Stop output (Output ﬁxed at OFF) ON

• Conguration Mode

CONFIGURATION MODE SW4-8

DIP switch setting (*) OFF

PC Conﬁgurator and communicaton ON

• Terminator DIP SW

TERMINATOR SW SW3

Without(*) OFF

With ON

Caution:BesuretosetunusedSW4-1through4-6toOFF.

R8-DC4C

P. 4 / 4EM-9743 Rev.1

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EXTERNAL DIMENSIONS unit: mm (inch)

115 (4.53)6 (.24)7 (.28) 6 (.24) 7 (.28)

DIN RAIL

(35 mm wide)

[3 (.12)] [4 (.16)]

12 (.47) 59 (2.32)

55 (2.17)

CONNECTION DIAGRAM

OUTPUT

CONNECTOR 1

OUTPUT

CONNECTOR 4

INTERNAL

BUS

EXC.

SUPPLY

BUS CONNECTOR

INTERNAL

POWER

*1. Not used.

Do4

Do1

WIRING INSTRUCTIONS

■ e-CON connector

connectorXN2D-1474-S002(Omron)

RecommendedcableconnectorXN2A-1470(Omron)*1

Applicablewiresize:0.08mm2(AWG28)-0.5mm2(AWG20)

Outersheathdiameter:max.1.5dia

*1. The cable connector is not included in the package.

Refertothespecicationsoftheproduct.

Otros manuales de Unidad de control de M-system

M-system

M-system R3-PA4 Manual de usuario

M-system

M-system R3-RS8 Manual de usuario

M-system

M-system F2DL Manual de usuario

M-system

M-system R7L-EC8A Manual de usuario

M-system

M-system R7 Series Manual de usuario

M-system

M-system R3-NEIP1 Manual de usuario

M-system

M-system R7M-EC16B Manual de usuario

M-system

M-system R7M-YS2 Manual de usuario

M-system

M-system R7M-DAC16C Manual de usuario

M-system

M-system 61A Manual de usuario

M-system

M-system R7ML-YV2 Manual de usuario

M-system

M-system R5-NM1 Manual de usuario

M-system

M-system R3-PD16A Manual de usuario

M-system

M-system R7M-CT4E Manual de usuario

M-system

M-system R7C-EC8B/UL Manual de usuario

M-system

M-system R7D-EA16 Manual de usuario

M-system

M-system R7M-DC4G Manual de usuario

M-system

M-system R7HL-DC8C Manual de usuario

M-system

M-system R7F4HD-DC32B Manual de usuario

M-system

M-system R7E-DC16A Manual de usuario

M-system

M-system R7E-DA16 Manual de usuario

M-system

M-system R1M-A1 Manual de usuario

M-system

M-system R7ML-EC16D Manual de usuario

M-system

M-system R3-SV8C Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario