M-system R3-PA16 Manual de usuario

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8389 Rev.7 P. 1 / 6

INSTRUCTION MANUAL

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Totalized pulse input module .............................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside the instrument

panel of a metal enclosure.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■HOT SWAPPABLE MODULES

• Replacing the module does not affect other modules on

the same base. Thus, the module can be replaced while

the power is ON. However, replacing multiple modules

at once may greatly change live voltage levels. We highly

recommend to replace them one by one.

■GENERAL PRECAUTIONS

• DO NOT set the switches on the module while the power

is supplied. The switches are used only for maintenance

without the power.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

INSTALLATION

Use the Installation Base (model: R3-BSx).

TOTALIZED PULSE INPUT MODULE

(Pi 16 points) MODEL R3-PA16

R3-PA16

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8389 Rev.7 P. 2 / 6

COMPONENT IDENTIFICATION

RUN LED

ERR LED

Status Indicator LED

■ FRONT VIEW ■ SIDE VIEW

SW3

1Count Reset

Count Reset Input

Set the Count Reset SW to OFF to start counting.

Functions

Count Setting

from Host PC/PLC

■STATUS INDICATOR LED

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;

Green when the bus B operates normally;

Amber when both buses operate normally.

ERR indicator: Bi-color (red/green) LED;

Red with excitation abnormality;

Green in normal operating conditions.

Input status indicator: Red LED; turns on with the input

ON.

■SIDE DIP SW

(*)Factory setting

• Count Reset: SW3-1

SW COUNT RESET

NORMAL COUNT RESET

SW3-1 OFF (*) ON

Note: Be sure to turn OFF during use.

• Count Reset Input: SW3-3

SW COUNT RESET INPUT

INVALID VALID

SW3-3 OFF (*) ON

• Count Setting from Host PC/PLC: SW3-4

SW COUNT SETTING FROM HOST PC/PLC

COUNT RESET COUNT PRESET

SW3-4 OFF (*) ON

(For option /PRS, count preset is ON)

Note : Be sure to set unused SW3-2 to OFF.

PC CONFIGURATOR

With conﬁgurator software, settings shown below are available.

Refer to the software manual of R3CON for detailed operation.

• Max. Pulse count: 1 to 65,535 (factory setting: 10,000)

• Totalized count value (V2.01 or higher)

• Accumulated pulse count (Pulse counts are changeable by using the PC Conﬁgurator, refer to “Counter setting from host

PC/ PLC” section hereafter.)

R3-PA16

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8389 Rev.7 P. 3 / 6

FUNCTIONS

■MANUAL COUNT RESET

1) Remove Network Module or its cables and interrupt com-

munication with other devices.

2) Turn ON the Count Reset SW.

3) Return the module to the base and turn the power supply

on.

4) ERR LED turns on and the module starts resetting its

counter. When the resetting is complete, the LED turns

to green. DO NOT remove the power while the red LED

is on. The RUN LED starts blinking at the same time.

5) After the green LED is conﬁrmed, turn the power supply

off.

6) Turn OFF the Count Reset SW.

7) Return the Network module onto the base and turn the

power supply on.

Note: Count Reset SW must be turned OFF after this proce-

dure because the module does not start counting with

ON state.

■REMOTE COUNT RESET INPUT

With the Count Reset Input SW (SW3-3) turned ON, the

Pi 16 pulse input can be used to remotely reset the count

values.

SW3-3 = OFF: Pi 16 is used as a pulse input.

SW3-3 = ON: Pi 16 is used to reset the count values for the

Pi 1 through Pi 15. One pulse supplied at the Pi 16 will be

recognized as a reset signal.

■REMOTE COUNT RESET OPERATION

1) ERR LED turns on (red color) when the reset signal is

received.

2) In 1 second, the module starts resetting its counter.

When the resetting is complete, the LED turns to green.

3) After 1 second, ERR LED turns back to the state before

the reset signal has been received.

Note: Reset signals received while the module is processing (1)

through (3) are ignored.

■COUNT RESET FROM HOST PC/PLC

Refer to “COUNTER SETTING FROM HOST PC/PLC” sec-

tion hereafter.

R3-PA16

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8389 Rev.7 P. 4 / 6

COUNTER SETTING FROM HOST PC/PLC

■COUNTER RESET

(Available for R3-NC1, R3-NC3, R3-NE1, R3-NM1, R3-NDx, R3-NFL1, R3-NP1, R3-NML3 (Firmware version 2.00 or later))

Setting SW3-4 OFF and turning power on enable the function.

The bits indicating the channels to reset counter are allocated in the ﬁrst word from host PC/PLC.

When these bits are changed from 0 to 1, the counter is reset. When it is conﬁrmed that the counter is reset, return to 0.

Notice that if the bit remains at 1, the next reset will not work.

Count reset CH.1

Count reset CH.16

Count reset CH.2

Count reset CH.3

Count reset CH.4

■COUNTER PRESET

(Available in combination with R3-NE1, R3-NM1 (Firmware version 2.00 or later), and R3-PA16 displayed ‘SW3-4 RESET/

PRESET’ on the right side)

Setting SW3-4 ON and turning power on enable the function.

Write the preset value to the Holding Resisters, which has same address as the Input Resisters.

• Input Resisters • Holding Resisters

Address

n+0

n+1

n+2

n+3

n+14

n+15

Input 1

Input 3

Input 15

Input 2

Input 4

Input 16

Address

n+0

n+1

n+2

n+3

n+14

n+15

Preset value of Input 1

Preset value of Input 3

Preset value of Input 15

Preset value of Input 2

Preset value of Input 4

Preset value of Input 16

R3-PA16

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8389 Rev.7 P. 5 / 6

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit: mm (inch)

130 (5.12)

27.5 (1.08) 109 (4.29)

POSITIONING

GUIDE

TERMINAL

COVER

20–M3

SCREW

6.2

(.24)

■CONNECTION DIAGRAM

1INTERNAL

BUS A

INTERNAL

BUS B*

BUS CONNECTOR

INTERNAL

POWER

Pi 1

Pi 16

Pi 15

Pi 14

Pi 13

Pi 12

Pi 11

Pi 10

Pi 9

Pi 8

Pi 7

Pi 6

Pi 5

Pi 4

Pi 3

Pi 2

COM(+)

+24V

■R3-PA16x/A

Pi 1

Pi 16

Pi 15

Pi 14

Pi 13

Pi 12

Pi 11

Pi 10

Pi 9

Pi 8

Pi 7

Pi 6

Pi 5

Pi 4

Pi 3

Pi 2

■R3-PA16x

*For dual redundant communication.

**DO NOT use the terminals No. 9 and 19.

R3-PA16

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8389 Rev.7 P. 6 / 6

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.5 N·m

■SOLDERLESS TERMINAL

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable. Solder-

less terminals with insulation sleeve do not ﬁt.

Applicable wire size: 0.3 – 0.5 mm2

Recommended manufacturer: Japan Solderless Terminal

MFG. Co., Ltd., Nichifu Co., Ltd.

12max

6max

3max 4min

3.2 dia.

(mm)

Tabla de contenidos

Otros manuales de Unidad de control de M-system

M-system

M-system R8-SVT8 Manual de usuario

M-system

M-system R7ML-EC16B Manual de usuario

M-system

M-system R5-NE1 Manual de usuario

M-system

M-system R3-RS8 Manual de usuario

M-system

M-system R7F4HML3-D-DAC32B Manual de usuario

M-system

M-system R7M-YV2-R Manual de usuario

M-system

M-system R3-GD1 Manual de usuario

M-system

M-system R3-NF3 Manual de usuario

M-system

M-system R7L-RR8 Manual de usuario

M-system

M-system R3-GM1 Manual de usuario

M-system

M-system R30YS4 Manual de usuario

M-system

M-system M8CD1 Manual de usuario

M-system

M-system 73VR3100 Manual de usuario

M-system

M-system 61F Manual de usuario

M-system

M-system R6-NE1 Manual de usuario

M-system

M-system R3-NF1 Manual de usuario

M-system

M-system R7ML-DC16A Manual de usuario

M-system

M-system R3-DS4 Manual de usuario

M-system

M-system R7C-EC16A Manual de usuario

M-system

M-system R7G4HH-A-YVF4 Manual de usuario

M-system

M-system R7F4DD-DC16A-H Manual de usuario

M-system

M-system R7L-EC8A Manual de usuario

M-system

M-system R3-SV8C Manual de usuario

M-system

M-system R3-NE1 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario