M-Power MP100 Manual de usuario

MP100

User’s Guide

Rev.F

Sep 2018

MP100 User’s Guide

Contents

Read Before Operating...................................................................................................................2

General Information.......................................................................................................................3

User Interface..................................................................................................................................3

Display..............................................................................................................................................4

Using MP100....................................................................................................................................5

Turn the unit on.......................................................................................................................5

Warm up sequence..................................................................................................................5

Normal mode...........................................................................................................................6

Real time reading ............................................................................................................6

STEL screen.....................................................................................................................6

TWAscreen......................................................................................................................6

Peak screen ......................................................................................................................6

Min screen (for Oxygen sensor only).............................................................................7

Turn the unit off ..............................................................................................................7

Config mode.....................................................................................................................................7

Enter Config mode..................................................................................................................7

Sensor calibration....................................................................................................................8

Calibration adapter.................................................................................................................8

Zero calibration.......................................................................................................................9

Span calibration......................................................................................................................9

Bump test...............................................................................................................................10

Change alarm limit ...............................................................................................................10

Change bump/cal interval ....................................................................................................11

Change span value ................................................................................................................12

Change display unit ..............................................................................................................12

Vibrator enable/disable.........................................................................................................12

Power on zero enable/disable ...............................................................................................13

Fast power on enable/disable ...............................................................................................13

Reset config............................................................................................................................13

Exit Config mode...................................................................................................................14

Maintenance ..................................................................................................................................14

Replace the battery ...............................................................................................................14

Replace the sensor filter........................................................................................................15

Replace the sensor.................................................................................................................15

Ordering information...................................................................................................................17

Specifications.................................................................................................................................18

Sensor configuration.....................................................................................................................19

Alarm signal summary .................................................................................................................20

Trouble shooting............................................................................................................................22

MP100 User’s Guide

Read Before Operating

This manual must be carefully read by all individuals who have or will have the responsibility of

using, maintaining or servicing this product. The product will perform as designed only if it is

used, maintained and serviced in accordance with the manufacturer’s instructions.

Warning

⚫Never operate the monitor when the cover is removed.

⚫Remove the monitor cover and battery only in area known as non-hazardous.

⚫Use only mPower’s lithium battery part number 1.17.02.0002 (3.6V, 2700mAH, AA size) or

part No. ER14505 cell manufactured by EVE Energy Co., LTD

⚫This instrument has not been tested in an explosive gas/air atmosphere having an oxygen

concentration greater than 21%.

⚫Substitution of components will impair suitability for intrinsic safety.

⚫Substitution of components will void warranty.

⚫It is recommended to bump test with a known concentration gas to confirm the instrument is

functioning properly before use.

⚫Before use, ensure that the ESD film on the display is not damaged or peeling.

Avertissement:

⚫N'utilisez jamais le moniteur lorsque le couvercle est enlevé.

⚫Retirer le couvercle du moniteur et la batterie uniquement dans une zone connue comme non dangereuse.

⚫Utilisez uniquement la batterie au lithium de mPower, pièce No. 1.17.02.0002 (3.6V, 2700mAH, taille AA)

ou celle de EVE Énergie Cie., Lté, pièce No. ER14505.

⚫Cet instrument n'a pas été testé dans une atmosphère explosive gaz / air ayant une concentration en oxygène

supérieure à 21%.

⚫La substitution de composants compromettra l'aptitude à la sécurité intrinsèque.

⚫La substitution des composants annulera la garantie.

⚫Il est recommandé de tester avec un gaz de concentration connu pour confirmer que l'instrument fonctionne

correctement avant de l'utiliser.

⚫Avant de l’utiliser, assurez-vous que le film ESD sur l'écran n'est pas endommagé ou épluché.

Proper Product Disposal at The End Of Life

The Waste Electrical and Electronic Equipment(WEEE) directive (2002/96/EC) is

intended to promote recycling of electrical and electronic equipment and their

components at end of life . This symbol (crossed-out wheeled bin) indicates

separate collection of waste electrical and electronic equipment in the EU

countries. This product may contain one or more Nickel-metal hydride (NiMH),

Lithium-ion, or Alkaline batteries. Specific battery information is given in this

user guide. Batteries must be recycled or disposed of properly. At the end of its

life, this product must undergo separate collection and recycling from general or

household waste. Please use the return and collection system available in your

country for the disposal of this product.

MP100 User’s Guide

General Information

UNI (MP100) is a single sensor, portable, personal toxic gas monitor. It displays gas

concentration continuously on a big segment LCD. It also monitors STEL, TWA, peak and min

(for O2only) value of the gas and can be displayed on demand.

High, Low, STEL&TWA alarm threshold values are configurable. The shell is made of high

strength, durable material. Two key operation, simple to use. Sensor and battery can be replaced

easily. Calibration is also very convenient.

User Interface

1. AudibleAlarm Port

2. LED alarm window

3. LCD

4. Left Key (Confirm/Number increasing)

5. Right Key (Power/ Cursor moving)

6. Alligator clip

7. Sensor

8. Vibrator

MP100 User’s Guide

Display

1. Gas name, includes: CO, H2S, SO2, O2, VOC

2. Question mark

3. OK

4. Gas unit, includes: x10-6, ppm, %, mg/m3, µmol/mol

5. Battery

6. HIGH, LOW, STEL, TWA alarm

7. Span calibration

8. Zero calibration

9. Number

MP100 User’s Guide

Using MP100

Turn the unit on

Press and hold the Right Key for 3 seconds, until LCD displays , buzzer beeps,

green LED flashes, then release the button, the unit is powered on.

Warm up sequence

After powered on, the unit enter warm up and self-test sequence, show the firmware version as

follows:

If the sensor is not able to be identified by the instrument or is not installed into the instrument,

then the screen switches between and .Otherwise, the

following values will be shown accordingly:

High alarm threshold value:

Low alarm threshold value:

STEL (short-term exposure limit) alarm threshold value:

MP100 User’s Guide

TWA (time-weighted average) alarm threshold value:

Normal mode

Real time reading

The unit enters normal mode, start monitoring gas concentration and display on the LCD screen.

User can check some other values like STEL,TWA, PEAK, and MIN (for O2only) by pressing the

Right Key.

*Unit will return to real time reading from any other screen when there’s no key action for 60

seconds.

STEL screen

TWA screen

Peak screen

Press the Left Key to clear peak value

MP100 User’s Guide

Press the Left Key again, peak value is cleared.

Min screen (for Oxygen sensor only)

Press the Left Key to clear min value

Press the Left Key again, minimum value is cleared

Turn the unit off

In normal display mode, press and hold the Right Key, then the unit will display a 5 second count

down, LEDs will flash and buzzer will beep once per second.

Config mode

In Config mode, user can do calibration & change parameters for the unit. In general, use the Left

Key to increase the number or confirm, use the Right Key to move the cursor or move to the next

programming item.

Enter Config mode

Press and hold the Left Key and the Right Key together for 3 seconds, the unit enters Config

mode.

The Config mode is password protected, LCD displays to prompt enter

password. The screen displays , with one digit flashing.

MP100 User’s Guide

To input password, use the Left Key to increase the number, use the Right Key to move cursor.

Once all four digits are input, the cursor will move to “OK”, use the Left Key to finish password

input and enter the Config mode.

If the digit input is mistaken, use the Right Key to move cursor between four digits and “OK”

mark, to change the input.

*MP100 preset password is 0000

Sensor calibration

Before the unit can monitor gas correctly, it needs to know the metric, this is done by zero

calibration and span calibration.

Calibration adapter

1. Calibration adapter is used to apply gas to the unit during calibration.

2. Before span calibration (in the following section), attach the Calibration Adapter over the inlet

port on the front of MP100 by pressing it into place.

3. Open the gas cylinder valve, then press the Left Key to start the calibration count down.

MP100 User’s Guide

4. Take off the Calibration Adapter and complete calibration.

When monitoring, never operate the MP100 with the Calibration Adaptor attached. The

MP100’s sensor operates by diffusion. If the Calibration Adapter is attached during normal

operation, inconsistent and lower-than-normal readings will occur because of decreased

concentration of the gas being monitored.

Zero calibration

Zero calibration is to set the base line for the sensor, it is done in fresh air. When LCD

displays , press the Left Key to start zero calibration. The unit will start a 15

second count-down, after the count-down is finished, zero calibration result will be displayed on

the LCD, pass or fail .

If user does not want to do zero calibration, during the 15 seconds count, press the Right Key,

LCD displays , zero calibration is aborted.

Span calibration

Span calibration is to set the metric of the sensor to the gas, it is done with a known concentration

gas. When LCD displays , apply the known gas to the unit, then press the Left

Key to start span calibration. Unit will start count-down, the count-down time depends on

Tabla de contenidos

Otros manuales de Detector de gas de M-Power

M-Power

M-Power UNI 321 Manual de usuario

M-Power

M-Power UNI MP100 Series Manual de usuario

M-Power

M-Power UNI 321 Manual de usuario

Manuales populares de Detector de gas de otras marcas

Macurco

Macurco GD-6 Manual de usuario

Evikon

Evikon E2632 Manual de usuario

Critical Environment Technologies

Critical Environment Technologies CGAS-A Series Manual de usuario

MSA

MSA altair 5 Manual de usuario

DOD Technologies

DOD Technologies ChemLogic CL96 Manual de usuario

DEGA

DEGA NS III LCD Series Manual de usuario

RKI Instruments

RKI Instruments 35-3001A-08-01 Manual de usuario

PEMTECH

PEMTECH PT2008 Series Manual de usuario

Coster

Coster RGS 328 Manual de usuario

Sygonix

Sygonix 2483186 Manual de usuario

Perry

Perry 1GA 50917MET/P Manual de usuario

isweek

isweek AS8900 Manual de usuario

Oldham

Oldham OLC 10 Manual de usuario

Wizmart

Wizmart NB983 Manual de usuario

Beacon

Beacon MEGA Manual

RKI

RKI GX-6000 Manual de usuario

Dräger

Dräger PIR 7000 Manual de usuario

GDS

GDS GASMAX EC Manual de usuario