LY International Electronics H-8000 Manual de usuario

CONFERENCE VIDEO PROCESSOR

H-8008

INSTRUCTION MANUAL

Video Camera Auto-Track Conference System

In modern society, the request of conference is not just limited on the simple sound, but

also requests the music, video backup records or remote transmission, this system is designed

for meeting this kind of requests. This system can implements connection between the

speaking and photography to implement the automatic tracking location photography function.

This system easy to operate, setting the photography spot through using the software, and it

can also setting the spot without the computer, so that to enhance the flexibility for using and

save the cost.

Function of Video Processor (H-8008)

1. Build-in video switching matrixes (8 input, 2 output).

2. 256 video camera auto-track control points. Multi-machine cascade

3. Support Pelco-D and VISCA protocol. (Pelco-D, Baud Rate: 9600, VISCA , Baud Rate:9600)

4. The processor can communicate with the equipments by RS232 interface, such computer or

video switching matrixes.

5. High speed dome follows the location for last opening of all speaking representative , when

the microphone which opened last was closed, the dome will follows back the last following

camera spot, and when all the speaking representative microphone were closed, the dome

will automatically moves back to the standby position.

6. When without the computer, set the camera spot advanced through pressing the button in

main unit board, and also set by the IR remote controller.

H-8008 Schematic diagram:

1. Power switch

2. IR Lens

3. Camera number selecting button (VIDICON 1-8), send the photography to the related

display screen through pressing this button

4. Power indicative lamp

5. Busy indicative lamp

6. Power indicator of each camera

7. Zoom setting

8. Camera direction set button (up, down, left, right)

9. Reset button (delete all the pre-setting spot)

10. Save button (save the pre-setting spot)

11. Data port (connect the conference main unit)

12. RS232 port (connect the computer)

13. High speed dome control port, RS485/RS232 (connect to the high speed dome data control

line)

14. High speed dome video input port (connect the high speed dome video signal)

15. Video port (connect the monitor)

16. Power supply (AC220V)

High speed dome characteristics:

18 times auto-focus len, focusing distance: 4.1~73.8 mm.

The horizontal direction can be 360 degrees unrestricted rotation, running speed can be up to

254 degrees / sec, vertical direction speed can be moved 95 degrees, running speed can be up

to 80 degrees / sec.

64 preset spots, can be set with programs and save, and call the preset spot freely for

Checking

63 high speed domes can be connected

Full-features automatic or manual control. aperture white balance, gain compensation with

reversible light and automatic gained. Both automatic and manual control is work.

Camera components: 1/4 Inch interline transfer CCD

Action pixels: 380,000 768(H)X 494 (V)

Resolution: 480 TVL

Please refer details operation in the camera using manual

Remote control using instruction:

The remote control used in setting automatic location for following camera preset spot, open

and install AAA battery when using, and take it out if don’t used for long time. Make sure the

central processor in the working state when setting, it is better to point the remote control to

the IR Lens in the central processor; Remote control transmitting distance is about 15M. Turn

on the related microphone in manual operation when setting (in FIFO mode), after debug the

required image by saving button and then to the next point of a preset settings

1. Remote control on/off button

2. Protocol setting ( original Pelco-D)

3. Baud rate setting (original 9600)

4. High speed dome choosing button(1-8)

5. Focus near

6. Focus far

7. Camera dome direction adjustment button: up, down,

left, right

8. Zoom +

9. Zoom –

10. Camera speed setting +

11. Camera speed setting –

12. Save, press this button for one second after set the

preset, then it will save the data

13. Reset, press this button for about 2 second, then it will delete all the camera preset, please

use it carefully.

14. Video-home, the video image will back to the video-home position when all mic off.

Connecting and operation instruction for camera central processor

1. Connect the data port in conference main unit to the data port in this unit with data cable

2. Connect the RS-232 port to the computer with computer cable

3. Install the software to the computer(optional)

4. Connect the high speed dome date cable to the dome port in this unit (if has many unit for

using, please use the multiple connecting), connect the high speed dome video cable

(within 8 sets) in to each input in the board behind the central processor (V1, V2, V3, V4,

V5, V6, V7, V8), the camera ID should be same as the video in port, it must configure

another distributor machine if over 8 sets, the high speed dome connect to the video

distributor

5. After confirmed the conference system is adjusted to normal, open the conference system

and this main unit, computer software; camera function setting and testing according to the

software instruction.

Port Schematic diagram

Name RJ45 DB9

Female

DB9

Male

RS485/RS422

BNC Power Data

Pic

Description

1.GND

2.GND

3.RS485A

4.RS485B-

5.NC

6.NC

7.GND

8.GND

1.NC

2.TXD

3.RXD

4.NC

5.GND

6.NC

7.NC

8.NC

9.NC

1.NC

2.RXD

3.TXD

4.NC

5.GND

6.NC

7.NC

8.NC

9.NC

1.RS485 A+

(TXD +)

2. RS485 B-

(TXD -)

3. RXD +

4. RXD –

5. GND

1.GND

2.VIDEO

1.POWER

2.GND

3.POWER

4.FUSE

1.RS485B-

2.RS485A+

3.AC24V

4.AC24V

Port name DATA RS232 DOME

(VISCA)

DOME

(PELCO-D)

INPUT/

OUTPUT

220V

POWER

DOME

DATA PORT

System connection:

Tabla de contenidos

Otros manuales de Sistema de conferencias de LY International Electronics

LY International Electronics

LY International Electronics H-8700 Manual de usuario

LY International Electronics

LY International Electronics H-8500 Series Manual de usuario

LY International Electronics

LY International Electronics H-7300 Manual de usuario

LY International Electronics

LY International Electronics H-7000D Manual de usuario

LY International Electronics

LY International Electronics H-2400M Manual de usuario

LY International Electronics

LY International Electronics H-3300 SERIES Manual de usuario

LY International Electronics

LY International Electronics H-8610 Series Manual de usuario

LY International Electronics

LY International Electronics H-7000 Manual de usuario

LY International Electronics

LY International Electronics H-9500 Series Manual de usuario

Manuales populares de Sistema de conferencias de otras marcas

Kramer

Kramer VIA GO Manual de usuario

AVT

AVT MAGIC AC1 Go Manual de usuario

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Manual de usuario

Sony

Sony PCS-I150 Manual de usuario

Middle Atlantic Products

Middle Atlantic Products VTC Series Manual de usuario

Prentke Romich Company

Prentke Romich Company Vanguard Plus Guía

Speakerbus

Speakerbus iD 712 Manual de usuario

Trelleborg

Trelleborg SafePilot CAT PRO Manual de usuario

Sennheiser

Sennheiser ADN Manual de usuario

ADTRAN

ADTRAN NetVanta 7100 Manual de usuario

AINA

AINA PTT Voice Responder Manual de usuario

Yamaha

Yamaha ProjectPhone PJP-100H Manual de usuario

vissonic

vissonic VLI Series Manual de usuario

Panasonic

Panasonic KX-VC500 Manual de usuario

Poly

Poly Trio 8300 Manual de usuario

Crestron

Crestron Mercury CCS-UCA-SMK Dibujo dimensional

Inmarsat

Inmarsat mini M Manual de usuario

Tenveo

Tenveo ALL-IN-ONE Manual de usuario